LCD Monitor Series 19.0 TFT Active Matrix LCD Panel 194X Series User’s Manual All Information in this manual may change from time to time without prior notice.
19.0 TFT Active Matrix LCD Panel User Manual Table of Content Table of Content .................................................................................. …2 Safety Instructions.............................................................................. …3 View of Monitor ....................................................................................... 4 Unpacking................................................................................................ 6 Warning........................
19.0 TFT Active Matrix LCD Panel User Manual Safety Instructions 1. Please read these safety instructions carefully. 2. Please keep this User‘s Manual for later reference. 3. Please disconnect this equipment from connecter before cleaning. Don‘t use liquid or sprayed detergent for cleaning. Use moisture sheet or cloth for cleaning. 4. Make sure the voltage of the power source when you try to connect the equipment to the power outlet. 5. All cautions and warnings on the equipment should be noted.
19.
19.
19.0 TFT Active Matrix LCD Panel User Manual Unpacking Thank you for your purchase. Please first check the following package content of the 19” LCD monitor. Contact your dealer or store where you purchased the LCD monitor if anything is missing. 19” TFT LCD Monitor External Univ15 pin D-sub (RGB Analog) input signal cable Power Cord Audio Cable with Stereo Phone Jack Quick Start Guide CD User’s Manual Quick Stand Warning 1. 2. 3. 4. 5. Make sure that the system power is turned off.
19.0 TFT Active Matrix LCD Panel User Manual Cleaning Notes 1. 2. 3. 4. Be gentle to clean the screen. Never use any kind of corrosiveness chemical dissolvent to clean the screen, it may hurt your screen surface. We suggest that a camel hair brush or a soft, lint-free cloth be used to clean the screen. Don’t exert any pressure directly to the LCD screen. Precaution 1. 2. 3. 4. 5. 6. 7. Do not expose the monitor to direct sunlight or heat. Do not spill liquid on the monitor.
19.0 TFT Active Matrix LCD Panel User Manual Hardware Installation Be careful to your LCD monitor. It’s very delicate and easy to break. Turn off LCD’s and PC’s power before installation. Follow the installation step by step described below. Input 【1】 【4】 【3】 【2】 【1】DC-IN：This is for connecting the power cable 【2】AUDIO-IN：This can be connected to the audio-out connector of any sound resource. 【3】VGA-IN : This can be connected with the D-Sub 15 pin signal cable.
19.0 TFT Active Matrix LCD Panel User Manual Hardware Installation Step by Step 1. Get ready with your Quick-Stand and hold your monitor firmly but gentle with your hands and let the panel facing you to pedestal the monitor on the Quick-stand. When you hear the “Click” that means you have set up your monitor in the first place successfully. 2. Turn your monitor upside down carefully with panel facing you to locate all connector port. 3.
19.0 TFT Active Matrix LCD Panel User Manual Hardware Installation Step by Step 4. Connect the audio cable to AUDIO-IN on the monitor, and the other side to computer line out. 5. Plug power cord onto the Power jack of the monitor. 6. Congratulations! You have just completed the hardware installation. How to Remove Quick-Stand of Monitor Remove Quick-Stand of the monitor by unlocking the six hooks as the illustration shows below when you need to deliver the monitor for any reason.
19.0 TFT Active Matrix LCD Panel User Manual Monitor Setup Button Menu control button Down OSD Menu Power Auto Adjust Up There 5 keys for user to set up the monitor, including “Power”, “MENU “, “AUTO”, ” <-> Down”, ” <+> Up”. Please refer to the introduction below. 1. “Power”: Turn the LCD power on and off. When the power is on, the light turns green, and standby in the color of orange. 2. “AUTO”: Exit and save the setting. Hot key for auto adjustment. 3.
19.0 TFT Active Matrix LCD Panel User Manual Troubleshooting If you encounter any trouble in using the monitor, make sure your monitor is properly installed according to the following steps before you call for service. ˙ There is no picture on the screen. Check: 1. Power saving mode. Press any key and move the mouse to deactivate the mode. 2. Signal Cable Connector Pins. If there are bent or missing pins, consult your dealer or store where you purchased the monitor.
19.0 TFT Active Matrix LCD Panel User Manual OSD (On-Screen Display) Menu Mode (PC Mode) BRIGHTNESS: Adjust the difference between light and dark area. BRIGHTNESS COLOR ADJUST: Adjust the RED, GREEN, and BLUE colors of the display. Click “ENTER” to adjust the R.G.B. color separately. COLOR ADJUST RED: Adjust the RED color of the display. RED BLUE: Adjust the BLUE color of the display.
19.0 TFT Active Matrix LCD Panel User Manual OSD (On-Screen Display) Menu Mode (PC Mode) COLOR TEMP: Adjust the color temperature of the display. COLOR TEMP BACK : Return to the Main Menu Screen BACK COLOCK: Adjust the re-flash ratio of the vertical scanning area. CLOCK PHASE: Adjust the re-flash ratio of the horizontal scanning area.
19.0 TFT Active Matrix LCD Panel User Manual OSD (On-Screen Display) Menu Mode (PC Mode) AUTO ADJUST: Automatically adjust the re-flash ratio of both vertical and horizontal scanning areas of the display. AUTO ADJUST H. POSITION: Adjust the horizontal viewing area of the display. H. POSITION V. POSITION: Adjust the Vertical viewing area of the display. V.
19.0 TFT Active Matrix LCD Panel User Manual OSD (On-Screen Display) Menu Mode (PC Mode) OSD H. POS: Adjust the Horizontal position of the OSD. OSD H. POS OSD V. POS: Adjust the Vertical position of the OSD. OSD V. POS OSD TIME: Adjust the displaying time of the OSD. OSD TIME OSD COLOR: Change the displaying color of the OSD.
19.0 TFT Active Matrix LCD Panel User Manual OSD (On-Screen Display) Menu Mode (PC Mode) OSD ALPHA: Adjust the Alpha volume of the OSD displaying. OSD ALPHA BACK: Return to the Main Menu Screen. BACK LANGUAGE: Change the language support to the language displaying of the OSD. LANGUAGE RESET: Reload the factory default setting of the display.
19.0 TFT Active Matrix LCD Panel User Manual OSD (On-Screen Display) Menu Mode (PC Mode) VOLUME: Adjust the sound volume of the embedded speaker of the display. VOLUME MUTE: Silence the embedded speaker of the display. MUTE BACK : Return to the Main Menu Screen BACK VGA / DVI: Switch to the VGA / DVI Signal inputs of the display.
.0 TFT Active Matrix LCD Panel User Manual Display Mode Incoming Display Mode Resolution Horizontal Frequency (KHz) Vertical Frequency (Hz) 720X400 (50Hz) 31.5KHz 50.0Hz 720X400 (60Hz) 31.5KHz 59.9Hz 720X400 (70Hz) 31.5KHz 70.1Hz 640X480 (50Hz) 31.5KHz 50.0Hz 640X480 (60Hz) 31.5KHz 59.9Hz 640X480 (66Hz) 35.0KHz 66.7Hz 640X480 (72Hz) 37.9KHz 72.8Hz 640X480 (75Hz) 37.5KHz 75.0Hz 800X600 (50Hz) 35.2KHz 56.3Hz 800X600 (60Hz) 37.9KHz 60.3Hz 800X600 (72Hz) 48.1KHz 72.
19.0 TFT Active Matrix LCD Panel User Manual Specification LCD Panel Type Viewing Angle Contrast Ratio Brightness Response Time Display Colors Max Resolution Pixel Pitch 19.0” TFT Active Matrix LCD Display H:160° , V:150° 700:1(MAX) , 500 : 1(Typical) 250 cd/m2(Typical) 8 ms(Typical) 16.7M colors 1280X1024(SXGA) @75Hz 0.294mm(H)x0.294mm(V) Input Signals RGB Analog VGA Level:0.
