Instruction Manual HDMI-UTPRO-0808 HDMI UTPro 8x8 Matrix Switcher HDMI-UTPRO-RX HDMI UTPro Receiver Matrix Switcher with Integrated Transport R EV F : 0 1 / 0 7 / 2 0 1 4
AMX Domestic Channel Partner Limited Warranty, Disclaimer and License (Excerpt from CHANNEL PARTNER TERMS AND CONDITIONS Versions 11.17.2011 with updates for previous version 8.25.2010 [sections 6.1 (a), (b) and (f)]) 6. LIMITED WARRANTY; RETURN, REPAIR AND REPLACEMENT 6.
Contents Contents ESD Warning ......................................................................................................................6 Important Safety Information and Instructions ...................................................................7 Information et directives de sécurité importantes..............................................................8 Notices .............................................................................................................................
Contents Defining and Executing Global Presets (Global Preset Mode)................................................................. 51 Executing Local Presets (Local Preset Mode)........................................................................................... 54 Locking and Unlocking (Lock Mode) ........................................................................................................ 55 Setup Options..................................................................................
Contents Appendix A – EDID Programmer ....................................................................................101 EDID Overview ...................................................................................................................................... 101 Determining the Need for EDID Programming...................................................................................... 102 Installing the EDID Programmer .....................................................................
ESD Warning ESD Warning To avoid ESD (Electrostatic Discharge) damage to sensitive components, make sure you are properly grounded before touching any internal materials. When working with any equipment manufactured with electronic devices, proper ESD grounding procedures must be followed to make sure people, products, and tools are as free of static charges as possible. Grounding straps, conductive smocks, and conductive work mats are specifically designed for this purpose.
Important Safety Information and Instructions Important Safety Information and Instructions When using and installing your AMX product, adhere to the following basic safety precautions. For more information about operating, installing, or servicing your AMX product, see your product documentation. Read and understand all instructions before using and installing AMX products. Use the correct voltage range for your AMX product.
Information et directives de sécurité importantes Information et directives de sécurité importantes Veuillez vous conformer aux directives de sécurité ci-dessous lorsque vous installez et utilisez votre appareil AMX. Pour de plus amples renseignements au sujet de l’installation, du fonctionnement ou de la réparation de votre appareil AMX, veuillez consulter la documentation accompagnant l’appareil. Lisez attentivement toutes les directives avant d’installer et d’utiliser les appareils AMX.
Notices Notices Copyright Notice AMX© 2014 (Rev F), all rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of AMX.
Notices Trademark Notices AMX®, NetLinx®, and InstaGate® are trademarks of AMX. Windows is a registered trademark of Microsoft Corporation in the United States and other countries. UL® and the UL logo are trademarks of UL LLC. TeraTerm is a copyright product of T. Teranishi and TeraTerm Project. PuTTY is a copyright product of Simon Tatham. HyperTerminal® is a copyright product of Hilgraeve Inc. 3M®, Desco®, Richmond Technology®, and Plastic Systems® are registered trademarks.
Overview and General Specifications Overview and General Specifications Applicability Notice The information in this manual applies to the HDMI-UTPRO-0808, Twisted Pair Dist Kit (FG1047-88K).
Overview and General Specifications HDMI UTPro Front Panel Components The HDMI UTPro comes standard with a front control panel. Even when another method of control is primary, the control panel can be used for system verification, redundant control, and troubleshooting. Control panel operation is covered starting on page 44. Function Key Select Key Control Dial LCD Input Keys (1-8) Power LED Output Keys (1-8) Cancel Key Take Key FIG.
Overview and General Specifications CPU / Serial Control The CPU is to the right of the power receptacle on the rear of the enclosure. Status LED Control (DB-9) port FIG. 3 Control port (DB-9 connector) CPU Components: Status LED – system status indicator Control port – serial port (DB-9) for attaching an external serial control device (see page 39) The Control (RS-232) port* can be used for matrix switching control functionality as an alternative to Native NetLinx control.
Overview and General Specifications HDMI Matrix Switching Connectors (1-8 HDMI Inputs and 1-8 HDMI Outputs) The HDMI matrix switching connectors (8 inputs left and 8 outputs right) are on the top as viewed from the rear of the enclosure. Information on cabling these connectors is on page 29, and special HDMI concerns and considerations are covered in the “Setting Up HDMI Systems” chapter (see page 60). HDMI matrix switching input connectors HDMI matrix switching output connectors FIG.
Overview and General Specifications HDMI-UTPRO-RX Receiver The HDMI-UTPRO-RX Receiver is used in conjunction with the HDMI UTPro 8x8 to assist in the transport of HDMI signals over UTP cable. Cables from the HDMI UTPro are connected to the HDMI-UTPRO-RX Receivers, which in turn are connected to the destination devices. In addition, the Receiver has ports for serial communication and IR control (FIG. 7). The size of the Receiver makes it easy to mount near or behind a high definition monitor.
Overview and General Specifications IR Control (Optional) Compatible IR Control Options: UDM-RC05 or MIO-R1 The following three items are required for IR control via the HDMI-UTPRO-RX Receiver. (These items are not included with the HDMI UTPro but must be ordered separately.) UDM-RC05 – The UDM-RC05 (FG1402-70) remote control can be used as a control interface to a UTPro system.
Overview and General Specifications HDMI-UTPRO-0808 Product Specifications HDMI-UTPRO-0808 Specifications Parameter Approvals Value UL, cUL, CE, FCC Class A, RoHS, WEEE Humidity 0 to 90% non-condensing Operational Temperature 32° F to 113° F (0° C to 45° C) Storage Temperature -22° F to 158° F (-30° C to 70° C) AC Power* 100 VAC to 240 VAC, single phase (50 Hz to 60 Hz) Power Consumption (max.) 110 Watts, fully loaded Thermal Dissipation (max.
Overview and General Specifications Rear Panel Components (continued) Serial Port (RJ-12) • Bi-directional RS-232 • Baud rates 115200, 57600, 38400, 19200, 9600, 4800, 2400, 1200 (default 9600) • RJ-12 connector NetLinx LED Blinks at 5 second intervals when a connection to a NetLinx Master is established. Status LED Non-functional. Ready LED Solid green indicates that NetLinx has fully booted and is ready.
Overview and General Specifications Digital Video – HDMI Specifications Digital Video – HDMI Specifications Compatible Formats HDMI, HDCP, DVI (DVI is supported with appropriate conversion cable) Supported Twisted-Pair Cable Types Cat5e, Cat6/6e, Cat6a, Cat7, STP, FTP Supported Twisted-Pair Cable Length • Up to 328 ft. (100 m); cable quality required in order to meet 100 meter distance should meet ANSI/TIA/EIA 568A-5 specification or better specification and be rated for 250 MHz or better.
Overview and General Specifications EDID Resolutions Supported through Local DDC for HDMI Connectors Standard and established timings are provided in the following tables along with detailed timing blocks. Note: The EDID can be re-programmed to support additional resolutions through the local DDC using the EDID Programmer (see page 101). Standard Timings Standard Timing Identification Resolution Refresh Rate Max. ID 1 1920x1080 (This is the preferred timing identified in the EDID.
Overview and General Specifications CEA Video Information Code (VIC) Formats VIC # Resolution Refresh Rate and Aspect Ratio VIC = 1 640x480p 59.94/60 Hz, 4:3 VIC = 2 720x480p 59.94/60 Hz, 4:3 VIC = 3 720x480p 59.94/60 Hz, 16:9 VIC = 4 1280x720p 59.94/60 Hz, 16:9 VIC = 5 1920x1080i 59.94/60 Hz, 16:9 VIC = 6 720(1440)x480i 59.94/60 Hz, 4:3 VIC = 7 720(1440)x480i 59.94/60 Hz, 16:9 VIC = 14 1440x480p 59.94/60 Hz, 4:3 VIC = 15 1440x480p 59.
Overview and General Specifications HDMI-UTPRO-RX Specifications HDMI-UTPRO-RX Specifications Parameter Value Approvals UL, cUL, CE, FCC Class A, RoHS, WEEE AC Power 100 VAC to 240 VAC, single phase (50 Hz to 60 Hz) DC Power 12 V to 24 V (+/-10%, desktop power supply included*) Power Consumption 12 Watts, fully loaded Thermal Dissipation 41 BTU/hr, fully loaded Operational Temperature 32° F to 113° F (0° C to 45° C) Humidity 0 to 90% non-condensing MTBF 203,000 hours (combined set of 8 RX
Overview and General Specifications Control Options HDMI UTPro systems support two main protocols: TCP/IP and XNNet (protocol used by control panel). Several control options are available. Multiple control methods can be used on the same system. Native NetLinx Interface The HDMI UTPro can be integrated with any NetLinx Central Controller and appears in NetLinx Studio (Version 3 or higher is required) as a NetLinx device. Front Control Panel The HDMI UTPro comes standard with a front control panel.
Installation and Setup Installation and Setup Site Recommendations When placing the enclosure, follow the recommendations and precautions in this section to reduce potential installation and operation hazards. Environment Choose a clean, dust free, (preferably) air-conditioned location. Avoid areas with direct sunlight, heat sources, or high levels of EMI (Electromagnetic Interference). To make control panel operations easier, mount the enclosure with the control panel in the rack at eye level.
Installation and Setup Reliable Earthing (Grounding) Reliable earthing of rack-mounted equipment should be maintained. If not using a direct connection to the branch circuit (e.g., plugging into a power strip), pay particular attention to supply connections. Caution: We recommend attaching all power cords to a surge protector and/or an AC line conditioner. Unpacking The HDMI-UTPRO-0808 Kit is shipped in two boxes (one contains the HDMI UTPro and the other contains the HDMI-UTPRO-RX units).
Installation and Setup System Diagram The diagram in FIG. 8 illustrates a basic A/V distribution system using an HDMI-UTPRO-0808 Matrix Switcher and eight HDMI-UTPRO-RX Receivers. Important: Each HDMI matrix switching output connector must be connected (with HDMI patch cable provided) to its corresponding HDMI transport input connector (1 to 1, 2 to 2, etc.).
Installation and Setup Installation Recommendations Write the system’s serial number in an easily accessible location before installing the HDMI UTPro in a rack. The system’s serial number is located in two places on the enclosure: on the left rear and on the left side of the enclosure near the power receptacle. The serial number also displays at the end of the product name in NetLinx Studio’s ZeroConfig tree. Use an earth-grounded power cord / system with the HDMI UTPro.
Installation and Setup To install and set up an HDMI UTPro in a rack: 1. Attach the rack ears per FIG. 10 (ears provided). FIG. 10 Attach rack ears to sides of enclosure 2. Place the enclosure in the rack and attach front-mounting screws to hold it firmly in place. Tip: When placing an enclosure, keep in mind that the optimal viewing angle for a control panel is eye level. 3. Attach the source devices; see “Attaching Cables for Switching/Transport” on page 29 and “Setting Up HDMI Systems” on page 60.
Installation and Setup Important Twisted Pair Cable Recommendations The requirements are the same for the twisted pair cable used with the ICS LAN 10/100 (Ethernet) connector and with the DXLink (RJ-45) connector. Twisted pair cable is designed to carry Full HD content over 100 meter (328 ft.) cables with control. For cable specifications, see page 19. In a typical installation, the cables should be stretched to their full length between the Transmitters and Receivers and the enclosure.
Installation and Setup LEDs on RJ-45 Connectors Green LED Yellow LED FIG. 11 RJ-45 connector LEDs The following information applies to the LEDs on the UTP (RJ-45) transport connectors on the HDMI UTPro enclosure and to the Input (RJ-45) connector LEDs on the Receivers.
Installation and Setup Important: Before attaching source and destination devices, we recommend reading the “Setting Up HDMI Systems” chapter for information on concerns and considerations you should be aware of when switching HDMI (see page 60). HDMI matrix switching input HDMI matrix switching output Source device HDMI cable HDMI patch cable HDMI transport input UTP cable up to 100 m (328 ft.) Destination device UTP (RJ-45) transport output HDMI-UTPRO-RX HDMI cable FIG.
Installation and Setup IR Control (Optional) For information on the equipment needed for IR control, see page 16. IR Receiver FIG. 15 IR Receiver (FG-IR03 - not included) To connect an IR Receiver to the HDMI-UTPRO-RX Receiver: 1. Connect the IR03 IR Receiver (FG-IR03) cable to the IR Rx port on the Receiver. 2. Run the cable and attach the IR receiver bud so that it has a clear line-of-sight with the intended remote control device. 3. Repeat Steps 1 and 2 as necessary for additional IR remote units.
Installation and Setup Establishing an Ethernet 10/100 Network Connection The LAN 10/100 (RJ-45) port provides Ethernet 10/100 BaseT connectivity. The following table lists the pinouts, signals, and paring for the port.
Installation and Setup LAN LEDs LEDs on LAN 10/100 (Ethernet) RJ-45 Connector NetLinx LED - Active connection Yellow LED - Speed Status Green LED - L/A (link/Activity) Status FIG. 18 LAN 10/100 port LEDs The LAN 10/100 port is an Ethernet link connector, handling Ethernet 10/100 connections for 100 Mbps (megabits per second) and 10 Mbps. (This connection is compatible with most Ethernet based LANs.) The two small rectangular LEDs on the LAN 10/100 connector indicate the following.
Installation and Setup To connect an HDMI UTPro to a LAN: 1. Complete the installation of the HDMI UTPro including power up of the system. 2. Insert one end of the RJ-45 link cable into the LAN 10/100 port on the enclosure. 3. Connect the other end of the RJ-45 link cable to a LAN hub or switch. The network will automatically assign a DHCP IP address (the assigned IP address can then be changed to a static IP address, see page 75). If the LAN does not utilize DHCP, see the “Workaround” below. 4.
Installation and Setup 2. Right-click anywhere in the Workspace and select Refresh Zero-Config List to generate an initial listing of all Zero-Config devices that have been detected (FIG. 20). 3. Click the plus symbol (+) to the left of the “AMX HDMI-UTPRO-0808” in the Zero-Config list to expand its information. The HDMI UTPro’s current IP Address is listed below the device name. To test the HDMI UTPro WebConsole connection: 1. Launch a browser on your PC. 2.
Installation and Setup Cable Adapter Kit for Serial port (RJ-12) Serial Port - Default Communication Settings The default serial settings for the Serial port are listed in the table below. The settings can be altered by sending SEND_COMMANDs to Port 2 of the HDMI UTPro (see page 87) or the Receiver (see page 92). Default Serial Port Settings Baud Rate 9600 Data Bits Serial port (RJ-12) connector 8 Parity None Stop Bits 1 Flow Control None FIG.
Installation and Setup RS-01 Adapter Cable (FG-RS01) The adapter cable can be ordered by itself for a DCE interface with female connection. Serial port as DCE interface with female connection: DB-9 Serial Port Pinouts (female connector) RS-232 Pin 2: TX signal Pin 3: RX signal Pin 5: GND Female FIG.
Installation and Setup Control Port (DB-9) The Control (DB-9 port) on the HDMI UTPro is reserved for firmware upgrades to the CPU. If needed, this port can also attach to a PC for using EDID Programmer or XNConnect software or for other traditional serial port functions (e.g., BCS commands or third-party control*).
Installation and Setup 2. Plug one end of the null modem serial cable into the Control (RS-232) port on the enclosure. Null modem serial cable FIG. 29 Attach null modem serial cable to serial port 3. Plug the other end of the serial cable into the serial port on the PC (or serial HDMI UTPro DB-9 Port Settings controller/device). 4. Open the serial communication software and set the PC’s port settings to match the HDMI UTPro default port settings (see table to the right).
Installation and Setup 5. Apply power to the source and destination devices. The Power indicator on the front of the enclosure illuminates (green), indicating that the enclosure is receiving power. The system is ready for a test switch (see the section below). Note: For information on checking the software version, see page 56. Control Panel Startup After applying power and turning on the enclosure, the LCD on the control panel illuminates and displays the Function menu screen (FIG. 30).
Installation and Setup 2. Press the Select Key to choose Change. This places the system in Change Mode (available Input and Output Keys turn blue). 3. Press Input Key 1. Input Key 1 flashes indicating that it is ready to switch. (Any outputs currently connected to Input 1 will turn white.) 4. Press Output Key 2. Output Key 2 illuminates indicating that it is ready to accept the switch. 5. Press the Take Key. Input 1 switches to Output 2, and the keys turn blue. 6.
Installation and Setup Installation Troubleshooting If the test switch did not execute correctly: Check the power indicator on the front of the enclosure. If it is not illuminated, check the power cords. Verify the status of the test switch. If using the control panel, press the Function Key, locate Status by scrolling with the Control Dial, press the Select Key, and press Output Key 2.
Operating the Control Panel Operating the Control Panel Control Panel Overview This section describes the components and features on the control panel on the front of the enclosure of the HDMI UTPro. Select Key Control Dial Cancel Key LCD Function Key Input Keys 1-8 Take Key Power LED Output Keys 1-8 FIG.
Operating the Control Panel Take Key The Take Key functions much like the Enter Key on a computer keyboard. Pressing the Take Key instructs the system to execute or disconnect a switch. Prior to pressing the Take Key, the individual operation components are selected by pressing the appropriate keys. Input Keys (1-8) and Output Keys (1-8) The Input and Output Keys correspond to the input and output connections on the rear of the enclosure.
Operating the Control Panel Function Menu Overview and Options The Function Menu is displayed on the control panel LCD screen and provides access to various control and setup options for the HDMI UTPro (FIG. 33). Use the Control Dial to scroll through the options in the Function Menu Use the Select Key to select options in the Function Menu Function Menu displayed on LCD screen FIG.
Operating the Control Panel The Function menu and its submenus access the following modes and lists: Function Menu Change Selecting Change places the system in Change Mode. • The control panel must be in Change Mode to execute switches. • While in Change Mode, select the Input and Output(s) Keys followed by the Take Key to execute switches (see page 48). Virtual Matrix Selecting Virtual Matrix accesses the VMs that are defined for the system. • The list contains 0:All and 1:Video.
Operating the Control Panel Note: When you put the panel in Change Mode, available keys will be blue and any unavailable ones will not be illuminated. The first blue key selected flashes white and the next key(s) selected turns white. You can toggle the non-flashing white keys between the selected (white) and deselected (blue) state before pressing the Take Key. For more information, see page 45. In an execute switch command either an input or an output can be selected first.
Operating the Control Panel Changing the Virtual Matrix Selecting Virtual Matrix accesses the VMs that are defined for the HDMI UTPro. The list contains 0:All and 1:Video (unless custom VMs have been created in XNConnect). The setting does not need to be changed as the system functions the same for either VM. Note: Virtual matrices are defined in XNConnect and stored in the system’s configuration file.
Operating the Control Panel Disconnecting Switches (Disconnect Mode) Disconnecting a switch deactivates the connection between an input (source) and one or more output (destination) devices. Disconnecting an input disconnects all outputs currently receiving that source signal. An output can only be connected to one input; therefore, disconnecting an output will only disconnect the connection between the output and the input that is routed to it.
Operating the Control Panel Verifying Signal Status (Status Mode) Signal status can be verified to confirm that a switch has executed properly or to confirm correct routing to multiple outputs (destinations). Input status and output status both function on the control panel. An output can only be connected to one input (source); therefore, verifying the status of an output will illuminate only the one input it is currently connected to.
Operating the Control Panel To define a global preset: This example defines Global Preset 3, and the example on the next page executes Global Preset 3. 1. Route the system to the desired state. 2. Press the Function Key. The Function menu appears. 3. Locate Global Preset by scrolling with the Control Dial. 4. Press the Select Key. The Global Preset submenu appears. 5. Scroll to Define Global. 6. Press the Select Key again to choose Define Global. The Define Global list appears. 7.
Operating the Control Panel To execute a global preset: 1. Press the Function Key. The Function menu appears. 2. Locate Global Preset by scrolling with the Control Dial. 3. Press the Select Key. The Global Preset submenu appears. 4. Press the Select Key again to choose Execute Global. The Execute Global Preset list appears. 5. Scroll to Global Preset 3. 6. Press either the Select Key or the Take Key. Global Preset 3 is executed, and the system returns to the Global Preset submenu. 7.
Operating the Control Panel Executing Local Presets (Local Preset Mode) A local preset is a predetermined set of switches on a particular virtual matrix that are routed simultaneously. They are stored in each enclosure’s configuration file and can be executed at anytime. “Local Preset” will not appear as a submenu option in the Function menu if local presets have not already been defined. In addition, they will not appear if the system is on a virtual matrix that does not have local presets.
Operating the Control Panel Locking and Unlocking (Lock Mode) Locking the panel prohibits access to the system and can prevent accidental switching. The control panel can be locked by entering a sequence of keys. The factory default password is the first five keys in the top row (Inputs 1, 2, 3, 4 and Output 1). The password can only be changed by using XNConnect (see page 114). Note: Locking the control panel only locks out operations from the front panel keys.
Operating the Control Panel Unlocking the Control Panel When the panel is locked and you press any key, the Unlock Panel screen appears and you have ten (10) seconds to enter the password, or the control panel remains locked. If you wait longer than 10 seconds, press any key again before entering the password. If you enter the wrong password while attempting to unlock the control panel, an invalid password message appears and the Cancel Key flashes.
Operating the Control Panel 3. Press the Select Key. The Setup Options submenu appears. 4. Press the Select Key again to choose Software Version. The Software Version screen appears. Version number 5. Scroll to see additional Software Version information. 6. Press the Cancel Key to return to the Setup Options submenu. Or Press the Function Key to return to the Function menu. Default Virtual Matrix The factory default virtual matrix for the HDMI UTPro is All.
Operating the Control Panel 6. Scroll to 2:Custom. 7. Press the Select Key The display returns to the top of the Setup Options submenu. 8. Cycle power to implement VM 2 as the default virtual matrix. Or Change the virtual matrix (see page 49) to immediately perform operations on the new default virtual matrix without cycling power. (The next time power is cycled, VM 2 will be implemented as the default virtual matrix.
Operating the Control Panel System Error Codes on Control Panel LCD If you are experiencing problems with your HDMI UTPro, you can enable error code reporting on the control panel’s LCD (see below). If the system has an error code associated with the problem, the error code will then display on the LCD. The most common error code likely to appear on the LCD is listed in the table.
Setting Up HDMI Systems Setting Up HDMI Systems Applicability Notice This chapter pertains to using the HDMI UTPro’s HDMI matrix switching connectors and the HDMI and UTP transport connectors in conjunction with HDMI-UTPRO-RX Receivers for setting up an HDMI system. The HDMI connectors are designed to route high-resolution HDMI or DVI signals with or without HDCP (High-bandwidth Digital Content Protection). DVI signals must be, single-link DVI signals and are connected only with the use of a cable adapter.
Setting Up HDMI Systems Five Steps in Content Protection Process 1. The HDMI UTPro uses an authentication protocol to verify that the display device is licensed to receive the content. 2. The transmitter on the source device uses authentication protocol to verify that the HDMI UTPro matrix switching input (RX) and any routed downstream sinks are licensed to receive the content. 3. The content is encrypted and transmitted. 4.
Setting Up HDMI Systems If a source could support 16 or more sinks downstream from the HDMI UTPro and a 17th sink is added downstream of the HDMI UTPro, the protected content stops transmitting and the HDMI matrix switching input automatically clears its cache. The input will authenticate each of the downstream sinks again, but when it reaches the 17th sink, the protected content stops transmitting and the cache is cleared.
Setting Up HDMI Systems HDMI-UTPRO-RX Destination Device HDMI-UTPRO-0808 (Repeater) Source Device Repeaters FIG. 38 Example #4 – Source device supports 3 sinks (R2, R3, and one destination device) downstream of R1 Determining Sink Support Maximum on a Source Device Determining how many sinks the source can support is necessary to make sure the system runs smoothly.
Setting Up HDMI Systems Example Determining Sink Support Example of Determining Sink Support (FIG. 39): FIG. 39 illustrates a source device that was checked and found to support only 5 sinks past R1. The check included the following: From a clear matrix state (the cache is clear), the source device was routed to Outputs 1, 2, 3, 4, and 5 one at a time as a stable image appeared on each destination device. When attempting to route the source device to the sixth output, all displays lost content.
Setting Up HDMI Systems Dealing with Sources with Limited Sink Support For sources with limited sink support, the following system design considerations and control suggestions are provided. System Design Considerations If at all possible, replace the source device with one with that supports more sinks. If a repeater is connected between the source and the HDMI UTPro and the repeater is not necessary, remove the repeater and connect the source device directly to the HDMI matrix switching input.
Setting Up HDMI Systems The virtual matrices in this example assume no repeaters are used upstream or downstream of the HDMI UTPro. This example is also used in “Appendix D – Creating Virtual Matrices” (see page 119). VM 1 – The sources connected to the inputs in orange (Inputs 1 through 6) each support 8 sinks and can be routed to any or all of the outputs in orange on VM 1 (Outputs 1 through 8).
Setting Up HDMI Systems When the system is initially set up, each first time switch to an output must go through the lengthy authentication process. After the initial authentication, the system “remembers” the destination device and significantly reduces the latency. Note: If necessary, EDID Programmer software (located at www.amx.com) is available for re-programming the HDMI connectors (see page 101).
Setting Up HDMI Systems The HDMI Connector’s Sink Key Cache If you need to persist the sink key cache on the HDMI UTPro matrix switching input connectors or clear persistence of the cache, follow the instructions provided. Important: These commands apply to the routing state of the entire system. In addition, all HDMI matrix switching inputs in the system receive the request. These commands cannot be sent to specific inputs.
HDMI UTPro WebConsole HDMI UTPro WebConsole Overview HDMI UTPro has a built-in WebConsole that allows you to make various configuration settings via a web browser on any PC that has access to the enclosure. The WebConsole consists of a series of web pages that are collectively called the “Configuration Manager” (FIG. 41). Click here to log in Hover mouse here to access the Admin drop-down menu FIG.
HDMI UTPro WebConsole HDMI UTPro IP address for HDMI UTPro Zero-Config tab FIG. 42 Zero-Config list showing network with HDMI-UTPRO-0808 Note: The serial number displays at the end of the product name in the Zero-Config tree. Accessing the WebConsole Caution: We strongly recommend that the WebConsole site be placed inside your network firewall and that system security be turned on. To access the WebConsole: 1.
HDMI UTPro WebConsole Admin Menu Several configuration pages are included in the Configuration Manager, all of which are accessed via the Admin drop-down menu (FIG. 44). FIG. 44 Configuration Manager - Admin drop down menu Click on an option in this menu to access each of the configuration pages, as described in the following sections. The Restore Settings menu option restores the factory default settings on both the Security Settings page and the Port Settings page.
HDMI UTPro WebConsole 4. Click Accept to send the command. The response appears in the Replies field on the right. Click Refresh to receive new replies (notifications) in the Replies field. New replies are added to the bottom of the list. Click Clear to clear the Replies field. Click Cancel to exit the page without saving any changes. To send commands to an HDMI-UTPRO-RX: 1. From the Device drop-down menu, select the target Receiver (RX 1 - RX 8) – only those connected display in the list. 2.
HDMI UTPro WebConsole Master Connection Tab Click the Master Connection tab in the Device Configuration page to view/edit the Master Connection for the HDMI UTPro (FIG. 47). FIG. 47 Device Configuration page (Master Connection tab) Use the options on the Master Connection page to view/edit the Connection Mode, Mode Settings and Authentication Settings for the HDMI UTPro’s connection to the NetLinx Master.
HDMI UTPro WebConsole Security Settings Select Security Settings from the Admin drop-down menu to open the Security Settings page (FIG. 48). Use the options on the page to specify security settings and login information for the HDMI UTPro. Note: If Security Settings are disabled and then enabled again, Login information remains in affect. FIG.
HDMI UTPro WebConsole Logging Into the Configuration Manager (With Security Enabled) Login is only required if the Web and/or Admin security options have been enabled on the HDMI UTPro. To log into the Configuration Manger (with security enabled): 1. Click the Login link in the upper-right corner of the initial page (FIG. 46 on page 72). The Login dialog box opens. FIG. 49 Configuration Manager - Login popup page 2.
HDMI UTPro WebConsole Anytime you click Reboot from any page in the WebConsole, the server reboots. The reboot updates information between the HDMI UTPro and the server. (The HDMI UTPro system itself does not reboot.) IP Settings DHCP • Click to toggle the DHCP setting on the HDMI UTPro (default = enabled). • When the DHCP check box is not selected, a static IP address (with the appropriate subnet) must be entered.
HDMI UTPro WebConsole Editing the Clock Manager Settings The WebConsole provides a Clock Manager (accessible from the Admin drop down menu) for selecting the current mode of the system time. Be sure to click Accept to save your changes. The changes take effect immediately. Clock Manager - Mode Manager Time Sync Settings Standalone – when this option is selected, the settings are modified on the same page. Be sure to click Accept after clicking Standalone and again after modifying the settings.
HDMI UTPro WebConsole Clock Manager - Daylight Savings (only available if Network Time is selected) The options on the Daylight Savings Manager page allows you to enable and disable daylight savings and to specify daylight savings start and end times. To adjust Daylight Savings setting in the Clock Manager: 1. From the Admin drop down menu, select Clock Manager (or select Mode from the Clock Manager submenu). 2. Under Time Sync, select Network Time and click Accept. 3. Click the Daylight Savings tab.
HDMI UTPro WebConsole Clock Manager - NIST Servers (only available if Network Time is selected) The options on the NIST Servers page allow you to select the NIST server that will be queried at each clock synchronization and allow you to add more NIST servers to the list. Note: Only one NIST server is selectable at any given time. To adjust NIST Servers settings in the Clock Manager: 1. From the Admin drop down menu, select Clock Manager (or select Mode from the Clock Manager submenu). 2.
HDMI UTPro WebConsole WebConsole Troubleshooting Check the following: Be sure all power, signal, and link connections on all of the equipment are secure. Be sure the HDMI UTPro is correctly plugged into a network with a DHCP server. Be sure the LEDs on the LAN 10/100 connector indicate activity and that the Ready LED is illuminated. Be sure the LED indicators on the NetLinx Master are functioning. Ping the system, i.e., at the DOS prompt enter: ping XXX.XXX.XX.XX (where XXX.XXX.XX.
HDMI UTPro WebConsole Changing the Proxy Setting If the HDMI UTPro does not open, you may need to add an exception in the Proxy Setting dialog box. The instructions below apply to Internet Explorer. To change these settings in another browser, consult its Help file. To add an exception to the proxy setting information: 1. From the Tools menu on the browser, select Internet Options. The Internet Options dialog box opens. 2. Select the Connections tab.
HDMI UTPro WebConsole 3. Click the LAN settings. The Local Area Network (LAN) Settings dialog box opens. If the Proxy server box is checked, so to Step 4. If the Proxy server box is not checked, check it before going to Step 4. Be sure Proxy server box is checked 4. Click Advanced. The Proxy Settings dialog box opens. HDMI-UTP-0808 5. In the Exceptions field, enter the appropriate HDMI UTPro’s IP address (page 69). 6. Click OK to exit each of the dialog boxes used in these steps.
HDMI UTPro NetLinx Programming HDMI UTPro NetLinx Programming Overview The HDMI UTPro recognizes a select number of SEND_COMMANDs. Use NetLinx Studio (Version 3 or higher is required) to send these commands to the HDMI UTPro. Device Numbering By default, the Device Number assigned to the HDMI UTPro is 05500 (in the WebConsole, the device’s number displays as 5500).
HDMI UTPro NetLinx Programming Note: Only HDMI-UTPRO-RX units that are physically connected to the HDMI UTPro will be represented in the Online Tree. The device number for each HDMI-UTPRO-RX Receiver currently connected to the HDMI UTPro is automatically designated a device number, based on the device number of the HDMI UTPro to which it is connected and to the number of the HDMI UTPro Output UTP (RJ-45) port (1-8) on the HDMI UTPro to which it is physically connected.
HDMI UTPro NetLinx Programming SEND_COMMANDs SEND_COMMANDs are sent to Port 1 on the HDMI UTPro. Note: All text is based on a Unicode index. HDMI UTPro SEND_COMMANDs CLIO Syntax: SEND_COMMAND ,"'CLIO'" Connect inputs to outputs with specified level (for virtual Variables: matrices).
HDMI UTPro NetLinx Programming HDMI UTPro SEND_COMMANDs (continued) ?CO Syntax: SEND_COMMAND ,"'?CO'" Returns connection status for Variables: the HDMI UTPro. • O# = output port number: 1-8 = Outputs 1-8 - a value of 0 or ALL means all outputs Example 1: SEND_COMMAND dvUTPro,"'?C'" Returns which inputs are connected for all outputs. Example 2: SEND_COMMAND dvUTPro,"'?C1'" Returns which input is connected to output 1.
HDMI UTPro NetLinx Programming SERIAL SEND_COMMANDs SERIAL (RS-232) SEND_COMMANDs are sent to Port 2 on the HDMI UTPro. GET BAUD command HDMI UTPro SERIAL SEND_COMMANDs GET BAUD The port sends the parameters to the device that requested the information. Get the RX serial port's current communication parameters.
HDMI UTPro Firmware Upgrades HDMI UTPro Firmware Upgrades Overview The NetLinx Studio software application (available for free download from www.amx.com) provides the ability to transfer KIT firmware files to a NetLinx device such as the HDMI UTPro. To prepare for a firmware upgrade: 1. Verify that the latest version of NetLinx Studio is on your PC. Use the Web Update option in NetLinx Studio’s Help menu to obtain the latest version. Or Go to www.amx.
HDMI UTPro Firmware Upgrades 2. Click the Browse (...) button to navigate to the target directory in the Browse For Folder dialog (FIG. 59). FIG. 59 Browse For Folder dialog (NetLinx Studio) The Send to NetLinx Device dialog opens The selected directory path is displayed in the Location field. Assuming that the specified target directory contains one or more KIT files, the KIT files in the selected directory are displayed in the Files list box, with the file’s last modified date and time (FIG. 60).
HDMI UTPro Firmware Upgrades Caution: If for any reason your KIT file transfer should fail, continue to retry the transfer until you are successful. Do not reboot the HDMI UTPro or change connections until the transfer is complete. Failure to complete this operation successfully may require a factory repair of the HDMI UTPro. Note: For additional information on using NetLinx Studio, refer to the “Programming Guide – NetLinx Integrated Controllers” (available at www.amx.com).
HDMI-UTPRO-RX NetLinx Programming HDMI-UTPRO-RX NetLinx Programming Overview The HDMI-UTPRO-RX Receiver recognizes a select number of NetLinx CHANNELs and SEND_COMMANDs. NetLinx programming is supported only if the HDMI-UTPRO-RX is connected to the HDMI UTPro (a native NetLinx device). The main Device SEND_COMMANDs are described on page 92. IR SEND_COMMANDs are described on page 93. SERIAL SEND_COMMANDs are described on page 96.
HDMI-UTPRO-RX NetLinx Programming CHANNELs Channel Function 255 • This channel on indicates that the RX has a valid UTP connection to the HDMI UTPro. • If the channel is off, the RX is incorrectly connected. • 1-253 Key presses from selected remote control. SEND_COMMANDs Device SEND_COMMANDs are sent to Port 1 on the HDMI-UTPRO-RX. Note: All text is based on a Unicode index. HDMI-UTPRO-RX SEND_COMMANDs ?FWVERSION Syntax: Returns the firmware version the RX.
HDMI-UTPRO-RX NetLinx Programming IR SEND_COMMANDs IR CHANNELs and SEND_COMMANDs are sent to Port 3 on the HDMI-UTPRO-RX. Important: Use only IR channel numbers 96 and below with the HDMI-UTPRO-RX. Channel numbers assigned to IR SEND_COMMAND can be renumbered using IR edit software. IR CHANNELs Channel Function 1-96 Generate the IR or serial command assigned to that channel.
HDMI-UTPRO-RX NetLinx Programming HDMI-UTPRO-RX IR SEND_COMMANDs (continued) CTOF This command sets the delay time between pulses generated by the 'CH' or 'XCH' send commands in tenths of seconds. Set the duration of the Off time (no signal) between IR Syntax: pulses for channel and IR SEND_COMMAND ,"'CTOF',
HDMI-UTPRO-RX NetLinx Programming HDMI-UTPRO-RX IR SEND_COMMANDs (continued) XCHM Syntax: Changes the IR output pattern for the 'XCH' send command. Variables: SEND_COMMAND ,"'XCHM-'" • extended channel mode = 0 - 4. Example: SEND_COMMAND dvRXIR,"'XCHM 3'" Sets the IR device's extended channel command to mode 3. Mode 0 Example (default): [x][x] SEND_COMMAND dvRXIR,"'XCH 3'" Transmits the IR code as 3-enter.
HDMI-UTPRO-RX NetLinx Programming SERIAL SEND_COMMANDs SERIAL (RS-232) SEND_COMMANDs are sent to Port 2 on the HDMI-UTPRO-RX. HDMI-UTPRO-RX SERIAL SEND_COMMANDs CHARD Set the delay time between all transmitted characters to the value specified (in 100 Microsecond increments). Syntax: SEND_COMMAND ,"'CHARD-
HDMI-UTPRO-RX NetLinx Programming HDMI-UTPRO-RX SERIAL SEND_COMMANDs (continued) set baud rate with SEND_COMMAN D SET BAUD Syntax: SEND_COMMAND ,"'SET BAUD ,,,'" Set the serial communication parameters.* Variables: • baud = baud rates are: 115200, 57600, 38400, 19200, 9600, 4800, 2400, 1200.
HDMI-UTPRO-RX IRL File Transfers HDMI-UTPRO-RX IRL File Transfers Overview The NetLinx Studio software application (available for free download from www.amx.com) provides the ability to transfer IR Library files to a NetLinx device such as the HDMI-UTPRO-RX Receiver. In the case of HDMI-UTPRO-RX Receivers, IRL files are transferred to the RXs, via the HDMI UTPro. FIG.
HDMI-UTPRO-RX IRL File Transfers Transferring IRL Files To send an IR Library (*.IRL) file to the HDMI-UTPRO-RX: 1. Choose Tools > File Transfer to open the File Transfer dialog (FIG. 63). FIG. 63 File Transfer dialog (NetLinx Studio) 2. Click the Add command button to open the Select Files for File Transfer dialog, and open the Other tab (FIG. 64). Use the Other tab if the file(s) you want to transfer are not included in the open Workspace.
HDMI-UTPRO-RX IRL File Transfers 6. Click Open. a. If the selected file has not been mapped to a device, the Enter Device Mapping Information dialog is displayed (FIG. 65). 5501 3 FIG. 65 Enter Device Mapping Information dialog (NetLinx Studio) b. Enter the device mapping information, and click OK to return to the Select Files For File Transfer dialog. IRL Files are sent to Port 3 (IR Device Port) on the HDMI-UTPRO-RX.
Appendix A – EDID Programmer Appendix A – EDID Programmer Applicability EDID Programmer software is provided for re-programming the EDID EEPROM chips on the HDMI UTPro if necessary. This software is available at www.amx.com.
Appendix A – EDID Programmer Determining the Need for EDID Programming Ideally the EDID analysis will have been completed during installation specification. If this was not possible but all of the system’s devices are now available, the most effective way to proceed is to test if the HDMI signal from each of the source devices can be routed through the HDMI UTPro to each of the destination devices. If they can, then EDID programming is not necessary.
Appendix A – EDID Programmer If EDID programming is necessary, you have two options: Install the EDID Programmer. Read the EDID from the destination device and write it to the HDMI input connector. Install the EDID Programmer. Check the “EDID Library” file at www.amx.com (search for EDID Library) to determine if one of the custom EDID files meets the needs of the equipment. (The custom EDID files are variants of base EDIDs.) Write the custom EDID file to the HDMI input connector.
Appendix A – EDID Programmer 2. Connect an HDMI cable to the PC using the PC’s spare monitor port (if your PC has a DVI port, use a DVI-to-HDMI cable adapter). 3. Connect the open end of the HDMI cable to the destination device (typically a monitor) from which the EDID information needs to be read. 4. Click the Refresh Display List button to update the Available Displays drop down list. 5. From the Available Displays drop down list, select the destination device from which you need to read the EDID. 6.
Appendix A – EDID Programmer 10. Save the connector’s EDID default as a backup (assumes the connector has factory default EDID programming). Click the Refresh Display List button. Select the device. Click the Read button. Click the Save button (select location, enter file name, and click Save). 11. Click the Open button to select the .edid file to be written to the HDMI input connector. 12. Click the Write button to write the EDID information to the HDMI input connector. 13.
Appendix B – Programmer’s Interface for System Diagnostics Appendix B – Programmer’s Interface for System Diagnostics System Component Information The HDMI UTPro displays system information in its splash screen* for diagnostic purposes. The information indicates the current status and well-being of the system components.
Appendix B – Programmer’s Interface for System Diagnostics Component Identity Settings Detailed information for a single system component can be specified by using its identity (i) number setting (i0 through i5) in the following table. Minimal information for all five components can be specified by using the identity number i0.
Appendix B – Programmer’s Interface for System Diagnostics Splash Screen Examples Note: AMX reserves the right to add to the contents of the splash screen at any time, without notice. Power-Up Splash Screen The first example is of the splash screen that displays when power is applied to the enclosure. When “Ready” appears, BCS commands can be entered for executing switches, verifying status, querying the system for diagnostic information, etc. [1:Enclosure] HDMI-UTPRO-0808 v1.4.
Appendix B – Programmer’s Interface for System Diagnostics ~scrv3i3! [3:Communication Interfaces] count = 4 [interface 1] detected [type] BCS mode RS232 port, 9600 (8/1/N/E/NS) [interface 2] detected [type] Block mode FP port, 115200 (8/1/N/NE/S) [interface 3] detected [type] BCS mode RS232 port, 9600 (8/1/N/E/NS) [interface 4] detected [type] Neuron bridge undetected. FIG.
Appendix C – Managing Configuration Files Appendix C – Managing Configuration Files Applicability Notice This appendix applies to XNConnect version 2.10.0. XNConnect’s version information is located under its Help menu. Version 2.10.0 supports full Device Discovery.
Appendix C – Managing Configuration Files Installing and Launching XNConnect Use XNConnect software only if you need to customize or change the configuration information from the original specification. Important: Even if XNConnect is already on your PC, install the newest version from www.amx.com. We strongly recommend uninstalling the old version of XNConnect before installing a new version.
Appendix C – Managing Configuration Files Discovering the System The discovery process queries the attached system for configuration information and properties, including information regarding assigned signals and virtual matrix definitions. The discovery process may take several minutes to complete. We recommend disconnecting any third-party control devices from the enclosure’s serial ports before starting the discovery process. To discover a system: 1.
Appendix C – Managing Configuration Files Virtual Matrices View The Virtual Matrices view displays properties of the existing virtual matrices. Most common tasks are conducted from this view, including customizing channel names and creating local presets. Hardware tab Virtual Matrices tab Highlighted device Properties of highlighted device Components of primary device Primary device Communication settings Device firmware version FIG.
Appendix C – Managing Configuration Files 4. Enter the new name in the Name field in the right-hand pane and press Enter. The new channel name replaces the default channel name in the Sources or Destinations list. Name field – Edit in place (displays selected channel) Customized channel name Selected channel Default channel name Note: If a channel is in more than one VM (virtual matrix), you must repeat Steps 3 and 4 for the channel in each of the VMs. 5.
Appendix C – Managing Configuration Files To set the password and load it to the control panel: 1. Discover the system (see page 112) or open the .xcl file (see page 111). 2. In the Hardware view, right-click the CP-15 control panel icon – this icon is used for the HDMI UTPro control panel. (If control panel icon is not displayed, double-click the Optima icon.) 3. Select Set Password from the drop-down menu. The Set Control Password dialog box opens. 4.
Appendix C – Managing Configuration Files 2. Click the Name New button. The Name New Preset dialog box opens. 3. Optional – Enter a different preset number (local presets do not need to be numbered sequentially). 4. Enter a name for the new preset. 5. Click OK. The Modify Preset dialog box opens. 6. For the first switch, click the source channel (input) and one or more destination channels (outputs). Select multiple destination channels by holding down the Control key while selecting the channels.
Appendix C – Managing Configuration Files 13. From the File menu, select Save As and save an .xcl file with a new name to the PC. (We strongly recommend making a duplicate copy every time the file is modified.) 14. If applicable – Reload the .xcl file from the CPU to the control panel according to the directions on page 58. Loading an .xcl Configuration File Once modifications have been made to the configuration file, the new file must be loaded onto the system’s CPU for the changes to be implemented.
Appendix C – Managing Configuration Files Restoring the Automatic Configuration Caution: Restoring the automatically constructed configuration will result in the loss of all custom .xcl configuration file modifications (local presets, passwords, etc.). To restore the automatically constructed configuration: 1. Connect the system to a PC (see page 39). 2. Open a terminal emulation program (e.g., TeraTerm, PuTTY, or HyperTerminal). 3. Enter: ~def! to restore the configuration. 4.
Appendix D – Creating Virtual Matrices Appendix D – Creating Virtual Matrices Applicability Notice: This appendix applies to XNConnect version 2.10.0. XNConnect’s version information is found under its Help menu. Overview The HDMI UTPro Matrix Switcher is pre-engineered at the factory. It is configured and ready to switch once the source devices, receivers, and destination devices are attached.
Appendix D – Creating Virtual Matrices Creating a New Virtual Matrix Important: Save a backup copy of the existing configuration file if you find it necessary to modify the file for any reason. Process Overview Creating a new virtual matrix involves creating virtual channels which must be assigned to the physical connectors and grouped into a virtual matrix. For more information on virtual matrices, see page 119. Four dialog boxes are used for creating a virtual matrix.
Appendix D – Creating Virtual Matrices Preparing Existing VMs We recommend preparing the configuration file for new VMs by making the following changes to the existing VMs. Important: Before making these changes: use Save As (under the File menu), make a backup copy of the current file with a new name, and save it to the PC. Change the name of the current VM 0 to a large two digit number (e.g., 55). In the event that you decide to reuse it later, the number can be changed again.
Appendix D – Creating Virtual Matrices 5. Click OK. The Assign Signals to Matrices dialog box opens. Select signal Check the settings Select enclosure Select the physical matrix Click Assign Matrix Click OK 6. From the Available Signals box, select the HDMI signal. 7. From the Enclosure and Physical Matrix drop-down lists, accept the defaults. 8. Click Assign Matrix. 9. Click OK to finalize the settings and close the dialog box. 10.
Appendix D – Creating Virtual Matrices 15. Click OK. The Manage Virtual Matrix Groupings dialog box opens again. 16. Under Select a Method, click Group by Pattern (this time through, the destinations will be assigned). 17. Specify the following parameters for the output channels: Under Pattern Type, select Sequential. Under Channel Type, select Destinations Only. From the Starting Channel drop-down list, select the first channel number “1” to be included.
Appendix D – Creating Virtual Matrices The three VMs created for the example on page 119 using the previous procedure are illustrated in FIG. 79 below. (Note that VM 55 at the bottom of the VM list was the original VM 0 discovered on the system and renamed for possible reuse later.) FIG.
Appendix E – ASCII / Hex Conversion Appendix E – ASCII / Hex Conversion Devices are typically controlled either by using ASCII text strings or the hexadecimal equivalent. Control codes can be entered into the hardware using ASCII, hexadecimal, or a combination of both where certain ASCII codes are difficult to enter (e.g. a carriage return).
In the ever-changing AV industry, continual education is key to success. AMX University is dedicated to ensuring that you have the opportunity to gather the information and experience you need to deliver strong AMX solutions. Plus, AMX courses also help you earn CEDIA, NSCA, InfoComm, and AMX continuing education units (CEUs).
