Operation/Reference Guide MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.
AMX Limited Warranty and Disclaimer This Limited Warranty and Disclaimer extends only to products purchased directly from AMX or an AMX Authorized Partner which include AMX Dealers, Distributors, VIP’s or other AMX authorized entity.
AMX Software License and Warranty Agreement • LICENSE GRANT. AMX grants to Licensee the non-exclusive right to use the AMX Software in the manner described in this License. The AMX Software is licensed, not sold. This license does not grant Licensee the right to create derivative works of the AMX Software. The AMX Software consists of generally available programming and development software, product documentation, sample applications, tools and utilities, and miscellaneous technical information.
FCC Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received; including interference that may cause undesired operation. Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
Table of Contents Table of Contents Introduction ........................................................................................................1 Overview .................................................................................................................. 1 Common Application....................................................................................................... 1 Features .................................................................................................
Table of Contents DHCP............................................................................................................................. 21 Configuring Wireless Network Access .................................................................... 22 Step 1: Configure the Device’s Wireless IP Settings ............................................... 22 Wireless communication using a DHCP Address ...........................................................
Table of Contents EAP Security & Server Certificates - Overview ....................................................... 65 EAP-LEAP ...................................................................................................................... 66 EAP-FAST ...................................................................................................................... 68 EAP-PEAP......................................................................................................................
Table of Contents @DPG...................................................................................................................................... @PDR ...................................................................................................................................... @PHE ...................................................................................................................................... @PHP .....................................................................
Table of Contents ^BRD ....................................................................................................................................... ^BSF........................................................................................................................................ ^BSP........................................................................................................................................ ^BSM..................................................................
Table of Contents ?BOP....................................................................................................................................... ?BRD ....................................................................................................................................... ?BWW ..................................................................................................................................... ?FON ....................................................................
Table of Contents ^RAF, ^RMF - Embedded Codes ................................................................................ 145 ^RMF....................................................................................................................................... 145 ^RSR........................................................................................................................................ 145 Escape Sequences .........................................................................
Table of Contents ^PHN-PRIVACY....................................................................................................................... ?PHN-PRIVACY ....................................................................................................................... ^PHN-REDIAL ......................................................................................................................... ^PHN-SETUP-DTMFDURATION ......................................................................
Table of Contents MIC.............................................................................................................................. 170 WEP ............................................................................................................................ 170 WPA ............................................................................................................................ 170 WPA2 ........................................................................................
Table of Contents 10 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.
Introduction Introduction Overview The MVP-5200i is a wireless-only ergonomic device capable of VoIP intercom telephone communications, quick wakeup and connection time, extended battery life for longer operation between charges and includes a 5.2" Color Active LCD to display a 800 x 480 pixel image with 262,144 colors. Models includes a 5.2" Color Active LCD to display a 800 x 480 pixel image with 262,144 colors, available in black (FG5966-01) and white (FG5966-02), or a 5.
Introduction The MVP-5200i comes with an integrated rear "kickstand", allowing it to be used and displayed away from a Charging Station if necessary (FIG. 2). It also comes with a pre-installed 802.11g WPA/WPA2 SDIO wireless card. Kickstand DC power jack Mini-USB port FIG. 2 MVP-5200i side view (with kickstand) MVP-5200i Specifications Models Available: • MVP-5200i-GB, 5.
Introduction MVP-5200i Specifications (Cont.) Power Modes: • ON: All necessary modules are powered up and device remains online with the NetLinx Master. • SLEEP: Only the backlight will be turned off after the user selectable time of inactivity has elapsed. Panel resumes the ON mode in ~ 1 second. • STANDBY: Power to all components other than the touch screen is turned off after the user selectable time of inactivity has elapsed. Device will turn back on by touching the screen.
Introduction MVP-5200i Specifications (Cont.) External Components Connector: 5-pin Mini-USB connector used for audio output to USB headphones, programming, firmware updates, and touch panel file transfer between the PC and the target panel. Note: When connecting the panel to PC using a CC-USB (or compatible) cable, be sure to power the panel On before attempting to connect the USB cable from the PC to the mini-USB port on the panel. DC power port: 2.
Introduction Memory The MVP-5200i comes with 128MB of Mobile DDRAM memory and 256 MB NAND Flash memory. Neither may be upgraded. Table Charging Station Connector Locations With the unit facing you, the mini-USB port (for programming and downloading firmware as well as connecting USB headphones using the AMX-provided adaptor cable) and the DC power port are located on the lower left side of the device (FIG. 3).
Introduction Navigation Wheel The MVP-5200i device uses a unique button wheel for all commands not directly involving the touchscreen. This wheel, known as a navigation wheel, is located in the upper right corner of the device (FIG. 4). Used with the touchscreen, the navigation wheel allows scrolling and adjusting by turning the wheel with a thumb or finger and then pressing down on one of the wheel’s compass points for up, down, left, and right.
Introduction Navigation Wheel Behavior in Each Power Mode The behavior of the navigation wheel LED is dependent upon its status, and whether the blink function for the LED while in sleep mode is enabled: Navigation Wheel behavior in each Power Mode Power Mode Power Status Enters Mode By - Exits Mode By - LED Behavior On (Full On) Battery Power N/A N/A ON ON On (Full On) External Power N/A N/A ON ON On (Full On) Charging N/A N/A BLINK BLINK Sleep (Display Off) Battery Power 1.
Introduction Turning on the MVP-5200i The MVP-5200i uses one of two methods to turn it on. These use either the navigation wheel or the touchscreen. To learn which method works for your panel: 1. Press any of the navigation wheel’s compass points and hold until the AMX splash screen appears on the touchscreen. 2. If the navigation wheel does not respond, press the touchscreen and hold until the AMX splash screen appears on the touchscreen.
Accessories Accessories Table Charging Station The MVP-5200i comes with the MVP-TCS-52 Table Charging Station (FG5966-1X) (FIG. 5), which acts both as a charging station and a direct power connection. The charging station is available in either white (FG5966-10) or black (FG5966-11). FIG. 5 MVP-TCS-52-GB Table Charging Station - Front MVP-TCS-52 Specifications Dimensions (HWD): • 8.0” x 4.75” x 3.5” (20.32cm x 12.07cm x 8.89cm) Weight: • .65 lbs (.
Accessories MVP-5200i Table Charging Station Charging station rear support FIG. 6 MVP-5200i in MVP-TCS-52-GB Table Charging Station Connections and Wiring The PS3.0 is used to supply power to the MVP-5200i by routing incoming power through the connector pins and charge the device’s internal battery Recharging To recharge the MVP-5200i, slide the device into the Table Charging Station cradle bottom-first and make sure the device is fully seated in the Charging Station.
Accessories Wall Charging Station The optional MVP-WCS-52 Wall Charging Station (FG5966-1X) offers the same recharging and connection features as the Table Charging Station, with the advantage of being placed within accessible locations where the table station is either inconvenient or impractical (FIG. 8). The Wall Charging Station is available in either white (FG5966-13) or black (FG5966-12). MVP-WCS-52 MVP-5200i Security Release button FIG.
Accessories MVP-WCS-52 Specifications (Cont.
Accessories Unique passwords may be entered for up to four unique users as well as the administrator. For more information on setting passwords, please refer to the Password Settings Page section on page 79. Recharging To recharge the MVP-5200i: 1. Slide the device into the Wall Charging Station cradle bottom-first and make sure the device is fully seated in the Charging Station. 2. Press the top of the MVP-5200i back until it clicks.
Accessories Make sure to measure the size of the intended hole before starting to cut it. 2. Select the knockout to be removed from the top of the box. The box has two knockouts, at the top left and the top right. To assist with wiring, and to avoid mechanical stresses on the wire and the mechanism of the Wall-Mounted Charging Station, the top right knockout is preferred for use. 3. Run the power cable through the knockout into the box. Pull out about six inches (15.
Accessories 6. Prepare the captive wires for the 2-pin 3.55 mm mini-captive wire connector used for the MVP-WCS52’s power supply: Preparing and connecting the captive wires requires the use of a wire stripper and flat-blade screwdriver. Strip 0.25 inch (6.35 mm) of wire insulation off all wires. Insert each wire into the appropriate opening on the connector. Turn the screws clockwise to secure the wires in the connector.
Accessories Screw holes Plastic back box Neodymium magnets MVP-WCS-52 Rubber feet FIG. 13 Installation of MVP-WCS-52 For ease of installation, put each screw on a neodymium magnet in the device’s interior compartment to keep them on hand until they are needed. 11. After fully seating the screws, wipe down the area around the screw holes with the alcohol prep pad from the Installation Kit. Take a rubber foot and remove its adhesive backing.
Accessories Installing the Optional Metal Rough-In Box The optional metal rough-in box (FG037-11) is 10 inches (25.40cm) wide at its widest dimension (wider than the bezel of the Wall Charging Station), and is only intended for pre construction installations (FIG. 14). The Metal Rough-In Box is used in conjunction with the Wall Charging Station’s plastic back box. The Metal Rough-In Box must be located behind 3/8" (0.95cm) to 3/4" (1.91cm) of wall/mounting surface material.
Accessories Other MVP-WCS-52 installations The Wall-Mounted Charging Station is designed to be installed in various different locations, such as into the face of a wooden podium or the top of a table. Depending upon the ability to wire it to a power source, WallMounted Charging Stations may be installed on vertical or horizontal surfaces composed of such materials as wood, brick, and glass.
Configuring Communication Configuring Communication Overview All control for a MVP-5200i touch panel is established through a NetLinx Master. Communication between the MVP and the Master consists of using either Wireless Ethernet (DHCP, Static IP) or USB. References to Ethernet in this manual focus on the use of Wireless Ethernet via the MVP’s WiFi Card. Before commencing, verify you are using the latest NetLinx Master and Modero panel-specific firmware.
Configuring Communication IR Communication In certain situations, the MVP-5200i may be used as an infrared remote device for other AMX controllers. The device can transmit IR over 20 feet (6.10 m) from the panel at frequencies of 38KHz, 455KHz, and 1.2MHz. IR receivers and transmitters on G4 panels share the device address number of the panel. The MVP-5200i includes an IR transmitter for communication between the device and the NetLinx Master and between separate devices.
Configuring Communication FIG. 18 Protected Setup page The default password for the Protected Setup page is 1988, but this may be changed at any time. For more information on the Setup and Protected Setup pages, refer to the Setup Pages section on page 41 and the Protected Setup Pages section on page 53. Setting the Panel’s Device Number In the Protected Setup page: 1. Press the Device Number field in the Device ID section to open the Device Number keypad. 2.
Configuring Communication Configuring Wireless Network Access The first step in connecting the MVP-5200i to a wireless network is to configure the wireless communication parameters within the device’s Wireless Settings page. This page only configures the card to communicate to a target AP: the device must still be directed to communicate with the correct Master.
Configuring Communication Wireless Communication Using a Static IP Address 1. From the Protected Setup page, press the Wireless Settings button to open the Wireless Settings page. Wireless communication is set within the IP Settings section of this page (FIG. 19). Check with your System Administrator for a pre-reserved Static IP Address to be assigned to the panel. This address must be obtained before continuing with the Static assignment of the panel. 2.
Configuring Communication To access the Site Survey Tool: 1. From the Protected Setup page, press the Wireless Settings button to open the Wireless Settings page. 2. Press the Site Survey button. This action launches the Wireless Site Survey page, which displays a listing of all detected APs in the communication range of the internal card. The card scans its environment every four seconds and adds any new APs found to the list. Every scan cycle updates the signal strength fields.
Configuring Communication Step 2: Configure the Card’s Wireless Security Settings The second step in setting up the wireless card is to configure the Wireless Settings page. This section configures both the communication and security parameters from the internal wireless card to the AP. The procedures outlined within the following sections for an 802.11g card facilitate a common security configuration to a target AP.
Configuring Communication Manually entering the SSID information into the appropriate fields by following steps 7 through 9. 3. From within the Wireless Settings page, click the Simple button. 4. In the Security Type field, select Open (FIG. 23). An Open security method does not utilize any encryption methodology, but does require that an alpha-numeric SSID be entered. This method sends out network packets as unencrypted text. FIG. 23 Wireless Security - Simple Mode 5.
Configuring Communication Automatically Setting SSID In the Protected Setup page: 1. Select Wireless Settings. 2. Press the Site Survey button at the bottom of the page to open the Wireless Site Survey page (FIG. 24). 3. Select a WEP secured AP from within the Site Survey page, and press the Connect button. . Select a target AP with the desired level of security Connecting to the AP begins the communication FIG. 24 Site Survey of available APs (Secured AP shown selected) 4.
Configuring Communication (SSID) field on the touch panel’s Network Name SSID field and on the AP’s Basic Wireless Configuration page. 5. Toggle the Encryption button (FIG. 25) until it reads either 64 Bit Key Size or 128 Bit Key Size. The 64/128 selection reflects the bit-level of encryption security. This WEP encryption level must match the encryption level being used on the AP. WEP will not work unless the same Default Key is set on both the panel and the Access Point.
Configuring Communication Ethernet Over USB The MVP-5200i device is the first G4 device to support an "Ethernet over USB" driver for panel downloads and firmware updates. This means that the device can connect to a host computer for updates through its Mini USB port instead of through a standard Ethernet port (FIG. 26). Mini-USB Port FIG.
Configuring Communication Click on Browse Select the folder that contains the 'linux.inf' file FIG. 28 Found New Hardware Wizard Installation Options dialog 7. Click on Next. 8. The Windows XP machine now searches for the suitable driver (FIG. 29). FIG. 29 Found New Hardware Wizard while searching for the driver 9. Once the system finds the driver, it displays its choice (FIG. 30). Click Finish to complete the driver installation. 30 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.
Configuring Communication FIG. 30 Completing the Found New Hardware Wizard When an IP address is assigned to the usb0 interface on the device, Windows XP will make an attempt to assign an IP address to the corresponding interface on the Windows side. Usually, this IP address is a random value and in a totally different subnet.
Configuring Communication 5. In the new window: Select Use the following IP Address. Under IP address, provide an IP address (ensure that it is in the same subnet as the IP address given to the usb0 interface on the MVP-5200i). Under Subnet mask, set the suitable subnet mask. Click on OK' 6. In the Local Area Connection 3 Properties window, click on OK. The user should now be able to run any TCP/IP application between the two systems.
Configuring Communication 6. Click the Edit Settings button to open the Virtual NetLinx Master Settings dialog (FIG. 34). FIG. 34 Virtual NetLinx Master Settings dialog 7. Enter the System number; the default is 1. 8. Click OK on all open dialogs to save your settings. 9. Click the OnLine Tree tab in the Workspace window to view the devices on the Virtual System. 10. Right-click on Empty Device Tree/System and select Refresh System to re-populate the list.
Configuring Communication 10. Press the Reboot button to reboot the device and confirm changes. Master Connection to a Virtual Master If configuring the panel to communicate with a Virtual Master on your PC via wireless Ethernet, the Master IP/URL field must be configured to match the IP Address of the PC. Make sure to use the Virtual System value assigned to the Virtual Master within NetLinx Studio. Before beginning: 1.
Configuring Communication 6. Click the Edit Settings button in the Communications Settings dialog to open the Virtual NetLinx Master Settings dialog (FIG. 37). FIG. 37 Virtual NetLinx Master Settings dialog 7. From within this dialog, enter the System number (default is 1) and note the IP Address of the target PC being used as the Virtual Master. This IP Address can also be obtained by following these procedures: On the PC, click Start > Run to open the Run dialog.
Configuring Communication 18. Press the Back button to return to the Protected Setup page, and Exit to return to the Setup page. 19. The USB connection will be signified by the WiFi/Wired/USB icon changing into a USB icon (FIG. 39). FIG. 39 USB icon Using G4 Web Control to Interact with a G4 Panel The G4 Web Control feature allows you to use a PC to interact with a G4-enabled panel via the Web.
Configuring Communication 5. Press the Enable/Enabled button until it toggles to Enabled and turns light blue. 6. The Network Interface Select field is read-only and displays the method of communication to the web. Wireless is used when a wireless card is detected within the internal card slot. This method provides an indirect communication to the web via a pre-configured Access Point.
Configuring Communication Using the NetLinx Master To Control the G4 Panel Refer to the particular NetLinx Master’s instruction manual for detailed information on how to download the latest firmware from www.amx.com. This firmware build enables SSL certificate identification and encryption, HTTPS communication, ICSP data encryption, and disables the ability to alter the Master security properties via a TELNET session.
Configuring Communication FIG. 43 Web Control VNC installation and Password entry screens 6. Click Yes from the Security Alert popup window to agree to the installation of the G4 WebControl application on your computer. This application contains the necessary Active X and VNC client applications necessary to properly view and control the panel pages from your computer. The G4 Web Control application is sent by the panel to the computer that is used for communication.
Configuring Communication 10. Click OK to send the password to the panel and begin the session. A confirmation message appears stating "Please wait, Initial screen loading.". The secondary window is then populated with the same G4 page being displayed on the target G4 panel. A small circle appears within the on-screen G4 panel page and corresponds to the location of the mouse cursor. A left-mouse click on the computer-displayed panel page equates to an actual touch on the target G4 panel page.
Setup Pages Setup Pages Overview The MVP-5200i features on-board Setup pages. Use the options in the Setup pages to access panel information and make various configuration changes. To access the Setup pages, press the center button of the navigation wheel and hold for 3 to 5 seconds (FIG. 45). Setup Page Access button: Press and hold for 3 to 5 seconds to access the Setup pages. FIG. 45 Setup Page Access buttons Setup Page The Setup page (FIG.
Setup Pages Setup Page (Cont.) Connection Status icon: The icon in the upper-right corner of each Setup page provides a constant visual indication of current connection status. Note: a Lock appears on the icon if the panel is connected to a secured NetLinx Master. Connection Status: Displays whether the panel is has external communication, as well as the encryption status of the Master, the connection type (Ethernet or USB), and to which System the panel is connected.
Setup Pages Protected Setup Pages Information on the Protected Setup pages is available on page 53. Information Button The Information button allows access of both the Project Information page, which contains data on the TPDesign4 file being used with the MVP-5200i, and the Panel Information page, which contains detailed information on the panel itself. To access these pages: 1.
Setup Pages Project Information Page (Cont.) Sales Order: Displays the sales order information. Purchase Order: Displays the purchase order information. AMX IR Ports: Displays the AMX IR channel ports used by the IR Emitter on the panel. • This information is specified in TPD4 (Project Properties > IR Emitters & Receivers tab).
Setup Pages Panel Information Page The Panel Information page provides detailed panel information (FIG. 49). FIG. 49 Panel Information page Features on this page include: Panel Information Page Back: Saves all changes and returns to the previous page. WiFi/Wired/USB Icon: The icon to the left of the Connection Status Icon displays whether the current connection to the Master is Wireless (image of a radio antenna), Wired (image of three networked computers), or USB (USB connection symbol).
Setup Pages Panel Information Page (Cont.) 46 Shutdown String: Displays the shutdown string used during a panel’s Shutdown mode. File System: Displays the amount of Compact Flash memory available on the panel. RAM: Displays the available RAM (or Extended Memory module) on the panel. MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.
Setup Pages Time & Date Settings Page The options on the Time & Date Settings page (FIG. 50) allows setting and adjusting of time and date information on the NetLinx Master. If the time and/or date on the Master is modified, all connected devices will be updated to reflect the new information. FIG. 50 Time and Date Settings page The MVP-5200i does not have an on-board clock, so the only way to modify a panel’s time without altering the Master is via NetLinx Code.
Setup Pages Audio Settings Page The Audio Settings page allows adjustment of volume levels and panel sounds settings (FIG. 51). FIG. 51 Audio Settings pages Features on these pages include: Audio Settings Page Back: Saves all changes and returns to the previous page.
Setup Pages Audio Settings Page (Cont.) Intercom Volume: Sets the volume level for intercom calls from another MVP-5200i: • Use the Up/Down buttons to adjust the Line-In volume level (range = 0 - 100). • The Line-In Level bargraph indicates the current Line-In level. Press the bargraph to the left or right of the graph marker to adjust the volume level in one-percent increments (range 0 - 100), or press the bargraph and hold to move the graph marker to the desired level.
Setup Pages Power Management Page The options on the Power Management page allow setting of power warning preferences and battery status information, and adjustment of the display times for battery warnings (FIG. 52). FIG. 52 Power Management page Features on this page include: Power Management Page Back: Saves all changes and returns to the previous page.
Setup Pages Power Management Page (Cont.) Shutdown: This value determines the number of hours or minutes that need to pass before the panel automatically shuts down. Once shut down, the device will have to be restarted. The Up/Down buttons alter the timeout value (in minutes). Use the Up/Down arrows to change the settings. A value of Off disables this feature.
Setup Pages 52 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.
Protected Setup Pages Protected Setup Pages The Protected Setup page (FIG. 53) provides secured access to advanced panel configuration options, including communication and security settings. The Protected Setup page is accessed through the Setup page (please refer to the Setup Pages section on page 41). To access the Protected Setup pages: 1. Press the center button of the navigation wheel and hold for 3 to 5 seconds to access the Setup pages. 2.
Protected Setup Pages Protected Setup Page (Cont.) Reboot/Shutdown Panel: • Pressing the Reboot button causes the panel to reboot after saving any changes. • Pressing the Shutdown button causes the panel to shut down after saving any changes. (If the panel is connected to external power, this feature is disabled.) Docking Station • Dock Status - Illuminates when the panel is docked and communicating with the Charging Station. • Undock Panel - Releases panel from Wall Mounted Charging Station.
Protected Setup Pages 2. Press the Shutdown button. 3. Disconnect any power source plugs or USB connections, if necessary. Security Settings The Security button on the Protected Setup page has three settings: Standard, Secure, and DoD. Pressing the button opens the Panel Security Setting popup window (FIG. 55) FIG.
Protected Setup Pages A transition from one security mode to another will reset the Protected/Web Control/ remote login password to the default value for the current security mode (please refer to the default passwords above). A transition to Secure or DoD mode will disable G4 Web Control. Although the security password features are immediate, a reboot must occur for all the new security mode features to fully take effect.
Protected Setup Pages Protected Setup Navigation Buttons The Protected Setup Navigation Buttons (FIG. 56) appear on the left edge of the Protected Setup page. Press to access the System Settings page, which contains IP Settings and Master Connection information. Press to access the Wireless Settings page, which allows configuration of wireless connection settings. Press to access the Calibrate page, which allows proper calibration of the panel.
Protected Setup Pages System Setting Page Elements (Cont.) Master Connection: Type: Mode: Sets the NetLinx Master communication values: Displays how the panel is connected to the Master. The connection may be Wireless (wireless connection) or Any (no connection). This field cannot be changed. Cycles between the connection modes: URL, Listen, and Auto. • Auto - In this mode, enter the System Number and a username/password (if applicable).
Protected Setup Pages Wireless Settings Page Use the options on the Wireless Settings page (FIG. 58) to configure communication settings for the wireless CF card (802.11b/g), and read the device number assigned to the panel. FIG. 58 Wireless Settings page (reads from and assigns values to the AP) Features on this page include: Wireless Settings Page Back: Saves all changes and returns to the previous page.
Protected Setup Pages Wireless Settings Page (Cont.) Access Point MAC Address: This unique address identifies the Access Point (AP) used by this panel for wireless communication (read-only). • Site Survey button: Launches the Wireless Site Survey page. The options on this page allow you to detect (“sniff-out”) all APs transmitting within range of the panel’s Wi-Fi card.
Protected Setup Pages Security Modes The Wireless Settings page has two buttons: Simple and Enterprise. Pressing the Simple button opens the Wireless Security: Simple Mode popup window (FIG. 59), which offers wireless security options suitable for most home and office environments such as Open (page 62), WEP (page 62), and WPA-PSK (page 64). For more secure options, such as for corporate environments, the Wireless Security: Enterprise Mode popup window (FIG.
Protected Setup Pages Open In the Wireless Security: Simple Mode popup window (FIG. 59), press the Security Type field to select Open. Open security does not utilize any encryption methodology, but requires an SSID (alpha-numeric) entry. This entry must match the Network Name (SSID) entry of the target AP so the panel knows what device it is using to communicate with the network. Open Settings SSID (Service Set Identifier): Opens an on-screen keyboard to enter the SSID name used on the target AP.
Protected Setup Pages WEP Settings (Cont.) Default Key: Cycles through the four available WEP key identifiers to select a WEP key to use. As the Default Key value is altered (through selection) the corresponding “Current Key” is displayed. Each Current Key corresponds to a WEP key. This feature is useful for accessing different networks without having to re-enter that networks’ WEP key. It is also sometimes used to set up a rotating key schedule to provide an extra layer of security.
Protected Setup Pages WPA-PSK Settings In the Wireless Security: Simple Mode popup window (FIG. 59), press the Security Type field to select WPAPSK. WPA-PSK security is designed for environments where using WPA or WPA2 is desirable, but an 802.1x authentication server is not available. PSK connections are more secure than WEP and are simpler to configure, since they implement dynamic keys but share a key between the AP and the panel (client).
Protected Setup Pages EAP Security & Server Certificates - Overview The following EAP types all support a server certificate: EAP-PEAP EAP-TTLS EAP-TLS All three of these certificate-using security methods are documented in the following sections. EAP Authentication goes a step beyond simply encrypting data transfers, but also requires that a set of credentials be validated before the client (panel) is allowed to connect to the rest of the network (FIG. 61).
Protected Setup Pages EAP-LEAP In the Wireless Security: Enterprise Mode popup window (FIG. 60), press the Security Type field to select EAP-LEAP. EAP (Extensible Authentication Protocol) is an Enterprise authentication protocol that can be used in both wired and wireless network environments. EAP requires the use of an 802.1x Authentication Server, also known as a Radius server. The configuration fields described below take variable length strings as inputs.
Protected Setup Pages FIG. 62 EAP-LEAP sample Cisco System Security page MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.
Protected Setup Pages EAP-FAST In the Wireless Security: Enterprise Mode popup window (FIG. 60), press the Security Type field to select EAP-FAST. EAP-FAST (Flexible Authentication via Secure Tunneling) security was designed for wireless environments where security and ease of setup are equally desirable. EAP-FAST uses a certificate file, however it can be configured to download the certificate automatically the first time the panel attempts to authenticate itself.
Protected Setup Pages EAP-FAST (Cont.) PAC File Location: This field is used when the previous Automatic PAC Provisioning option has been Disabled. • When pressed, the panel displays an on-screen PAC File Location keyboard which allows you to enter the name of the file containing the PAC shared secret credentials for use in authentication. • This field is only valid when the automatic PAC provisioning feature has been enabled via the previous field.
Protected Setup Pages EAP-PEAP (Cont.) Certificate Authority: When pressed, the panel displays an on-screen Certificate Authority (CA) File Location keyboard, which allows you to enter the name of the certificate authority file which is used to validate the server certificate.This field is optional. If a server certificate is used, it should first be downloaded into the panel and the Certificate Authority field should then be set to the name of that certificate file.
Protected Setup Pages EAP-TTLS In the Wireless Security: Enterprise Mode popup window (FIG. 60), press the Security Type field to select EAP-TTLS. TTLS (EAP Tunneled Transport Layer Security) is an authentication method that does not use a client certificate to authenticate the panel. However. this method is more secure than PEAP because it does not broadcast the identity of the user.
Protected Setup Pages EAP-TTLS (Cont.) Inner Authentication Type: When pressed, this field cycles through the choices of available Inner Authentication mechanism supported by the Devicescape Secure Wireless Client: • EAP-MSCHAPv2 • EAP-GTC • EAP-OTP • EAP-MD5 • MSCHAPv2 • MSCHAP • PAP • CHAP Cancel/Save: • Cancel - discard changes and return to the previous page. • Save - store the new security information, apply changes, and return to the previous page.
Protected Setup Pages EAP-TLS (Cont.) Client Certificate: Opens an on-screen keyboard for entering the name of the file containing the client (panel) certificate for use in certifying the identity of the client (panel). • Refer to the Client Certificate Configuration section on page 73 for information regarding Client Certificates and their parameters.
Protected Setup Pages Certificate files frequently use 5 file extensions. It can be confusing because there is not a one to one correspondence. The following table shows the possible file extension used for each certificate type: Certificates and their Extensions Certificate Type PEM Possible File Extensions .cer .pem .pvk DER .cer .der PKCS12 .pfx Please note which certificate types are supported by the different certificate fields used on the configuration screens (PEAP, TTLS, and TLS).
Protected Setup Pages Calibrate Page The Calibrate page (FIG. 63) allows you to calibrate the touch panel for accurate button selection. FIG. 63 Calibrate page 1. Press and hold the center button on the navigation wheel for 6 seconds to access the Calibrate page (see FIG. 53). 2. Press the crosshairs in turn. If the crosshairs are not touched within ten seconds, the MVP-5200i will return to the Protected Setup page. 3. The page will read "Calibration Successful. Touch to continue.
Protected Setup Pages G4 Web Control Settings Page An on-board VNC (Virtual Network Computing) server allows the panel to connect to any remote PC running a VNC client. Once connected, the client can view and control the panel remotely. The options on this page allow you to enable/disable G4 Web Control functionality(FIG. 64). FIG. 64 G4 Web Control page Features on this page include: G4 Web Control Settings Page Back: Saves all changes and returns to the previous page.
Protected Setup Pages G4 Web Control Page (Cont.) G4 Web Control Timeout: Sets the length of time (in minutes) that the panel can remain idle, detecting no cursor movements, before the G4 Web Control session is terminated.
Protected Setup Pages Other Settings Press the Other Settings button to display the three settings options for Cache, Passwords, and SIP. Press one of the options within three seconds, or the three options buttons will slide back behind the Other Settings button. Cache Settings Page The options on the Cache Settings page (FIG. 65) allow setting and clearing of the flash memory cache, as well as viewing the status of the current cache settings.
Protected Setup Pages Cache Settings Page (Cont.) RAM Hit Rate: The number of times the RAM cache was referenced since the last cache clearing. Items In Cache (RAM): The total number of cached images in the RAM cache. Flash Current Size: The maximum size allocated to the flash cache. Flash Hit Rate: The number of times the flash cache was referenced since the last cache clearing. Items in Cache (Flash): The total number of cached images in the flash cache.
Protected Setup Pages Password Settings Page (Cont.) Enable/Enabled: The Enable/Enabled button allows you to toggle between activating or deactivating the MVP panel requirement of a user to enter a pre-defined password before removing the panel from a connected docking station: • Enable - does not prompt the user for a password, the docking station just releases the panel when the security release pushbutton is pressed.
Protected Setup Pages SIP Settings Page The options on the SIP Settings page (FIG. 67) enable you to establish network settings for using your touch panel as an IP phone. With a CSG SIP Communications Gateway (FG2182-01, -02, -03), you can use your touch panel to make and receive local, long distance, and international phone calls, and have access to phone features like call waiting, caller ID, call forwarding, call queuing, and voice mail.
Protected Setup Pages STUN Address: This option enables you to enter the IP address or DNS name of the Simple Traversal of UDP through NATs (STUN) server. This field is optional. Local Domain: This is the realm used for authentication. This field is optional. User Name: This option enables you to enter the user name used for authentication to the proxy server. Normally, the user name is the same as the phone number assigned to the extension you are using. This field is optional.
Protected Setup Pages Tools Press and hold the Tools button to access the MVP-5200i’s Panel Logs, Panel Statistics, and Connection Utility buttons. Each of these buttons opens a separate page, covered in detail below. The Tools button menu will remain visible for three seconds, regardless of whether or not the button continues to be held. Panel Connection Logs Page The Panel Connection Logs page (FIG. 68) chronicles all previous connections between the device and the network. FIG.
Protected Setup Pages Panel Statistics Page The Panel Statistics page (FIG. 69) displays activity between the device and the network in proportions of ICSP messages, blink messages, and Ethernet versus wireless use. FIG. 69 Panel Statistics Page Panel Statistics Page Back: Saves all changes and returns to the previous page.
Protected Setup Pages Connection Utility Page The Connection Utility page (FIG. 70) displays the current wired and wireless connection information, including the latest link quality and signal strength information. FIG. 70 Connection Utility Page Connection Utility Page Connection Information: Master IP: The IP address for the network’s Master. Wired Panel IP: The IP address used by the device for wired connections. Wireless Panel IP: The IP address used by the device for wireless connections.
Protected Setup Pages 86 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.
Upgrading Firmware Upgrading Firmware Overview For the purpose of panel downloads, the MVP-5200i’s download procedure is not compatible with other AMX panel devices. This is due to the unique configuration of the device. The first major change from other AMX devices is that the MVP-5200i uses dynamic Setup Pages for its displays. Instead of requiring a separate Setup Page project built within TPDesign 4, the MVP-5200i uses only a single set of Setup Pages for all of its supported resolutions.
Upgrading Firmware FIG. 71 Master Communications Settings dialog box 2. Click the Communications Settings... button to open the Communications Settings dialog box (FIG. 72). FIG. 72 Communications Settings dialog box 3. Click on the NetLinx Master radio button from the Platform Selection section. 4. Click on the Virtual Master radio box from the Transport Connection Option section to configure the PC to communicate directly with a panel.
Upgrading Firmware 7. In the Available Connections section, click on the IP address for the touch panel to select it. 8. In the Virtual NetLinx Master Settings dialog box, click OK to close the box. 9. In the Communications Settings dialog box, click OK to close the box. 10. In the Master Communications Settings dialog box, click OK to save your settings and return to the main NetLinx Studio application. 11. Click the OnLine Tree tab in the Workspace window to view the devices on the Virtual System.
Upgrading Firmware Virtual Master firmware version and device number Netlinx Studio version number MVP panel firmware version and device number FIG. 74 NetLinx Workspace window (showing panel connection via a Virtual NetLinx Master) The panel-specific firmware is shown on the right of the listed panel. Download the latest firmware file from www.amx.com and then save the Kit file to your computer. Note that each Kit file is intended for download to its corresponding panel.
Upgrading Firmware 8. Select the appropriate Kit file from within the Browse for Folder window (FIG. 76). FIG. 76 Browse for Folder window 9. Select the panel’s Kit file from the Files section. 10. Enter the Device value associated with the panel and the System number associated with the Master (listed in the OnLine Tree tab of the Workspace window). The Port field is greyed-out. 11. Click the Reboot Device checkbox if it is not already checked.
Upgrading Firmware A Special Note for Network Interface Connections Due to any USB connection to your PC being made through a Network Interface Connection (NIC), Windows will automatically make any new NIC connection the Primary connection. If this happens, the USB address of 172.16.0.2 will show up across the PC’s network switches as the PC’s source address. In some cases, network administrators will notice the NIC connection and reconfigure any PC that has connected to the MVP-5200i.
Upgrading Firmware 3. From the Advanced menu, select Advanced Settings... to open the Advanced Settings window (FIG. 78). FIG. 78 Advanced Settings window 4. Under the Adapters And Bindings tab, the user needs to make sure the Local Area Connection is not at the top of the Connections list. If it is at the top of the list (FIG. 78), select it and use the down arrow to the right of the list to move it to the bottom of the list (FIG. 79). FIG. 79 Moving the Local Area Connection 5.
Upgrading Firmware FIG. 80 Bindings for Local area list detail 6. When finished, click OK to close the Advanced Settings window and save all changes. 94 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.
Programming Programming Overview You can program the MVP-5200i, using the commands in this section, to perform a wide variety of operations using Send_Commands and variable text commands. A device must first be defined in the NetLinx programming language with values for the Device: Port: System (in all programming examples - Panel is used in place of these values and represents all Modero panels).
Programming Animated Transitions Animated transitions are used to add motion and effects to the transition from one page to another on a panel. With existing panel firmware, page flip transitions occur with the new page immediately drawing over the existing page on the screen. With animated transitions, the old page is moved, faded, or overdrawn from the screen while the new page is drawn. These operations use the OpenGL hardware accelerator to ensure smooth transitions.
Programming Since the transitions require OpenGL hardware acceleration, they are not seen by the user on a VNC connection. When a transition is triggered, the user will see a normal page flip to the new page on the VNC connection, while the animated transition occurs as expected on the panel. Transition Commands ^AFP Flips to a page with the specified page name using an animated transition. Flips to a page with the specified page name using an animated transition.
Programming Touch Gesture Recognition Gesturing refers to the act of moving a finger or stylus across the overlay and having the panel recognize and process this motion as a gesture. Once a gesture is detected, it is processed as another external button on the panel. This enables the user to design pages that translate gesture operations into any functionality available to external buttons.
Programming Gesture Prioritization (Cont.) The user double taps outside of a button This will be registered as a gesture. or slider. Gesture VNC/Mouse Support Gestures are recognized whether or not the user is using a finger or stylus on the panel's screen overlay, a mouse on a VNC connection, or a mouse connected to the local USB port on the panel. Gesture Custom Event Whenever a gesture is recognized and processed a custom event is also sent to the master.
Programming Page Commands These Page Commands are used in NetLinx Programming Language and are case insensitive. Page Commands @APG Add a specific popup page to a specified popup group. Add the popup page to a group if it does not already exist. If the new popup is added to a group which has a popup displayed on the current page along with the new pop-up, the displayed popup will be hidden and the new popup will be displayed.
Programming Page Commands (Cont.) @PHP Only 1 coordinate is ever needed for an effect; however, the command will specify both. Set the hide effect This command sets the location at which the effect will end at. Syntax: position. "'@PHP-;,'" Variable: popup page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
Programming Page Commands (Cont.) @PPG Toggle a specific popup page on either a specified page or the current page. If the page name is empty, the current page is used (see example 2). Toggling refers to the activating/deactivating (On/Off) of a popup page. This command works in the same way as the ’Toggle Popup’ command in TPDesign4. Syntax: "'@PPG-;'" Variable: popup page name = 1 - 50 ASCII characters. Name of the popup page. page name = 1 - 50 ASCII characters.
Programming Page Commands (Cont.) @PPT If timeout is empty, popup page will clear the timeout. Set a specific popup page to timeout within a specified time. Syntax: "'@PPT-;'" Variable: popup page name = 1 - 50 ASCII characters. Name of the popup page. timeout = Timeout duration in 1/10ths of a second. Example: SEND_COMMAND Panel,"'@PPT-Popup1;30'" Sets the popup page ’Popup1’ to timeout within 3 seconds.
Programming Page Commands (Cont.) PPOF Deactivate a specific popup page on either a specified page or the current page. If the page name is empty, the current page is used (see example 2). If the popup page is part of a group, the whole group is deactivated. This command works in the same way as the ’Hide Popup’ command in TPDesign4. Syntax: "'PPOF-;'" Variable: popup page name = 1 - 50 ASCII characters. Name of the popup page. page name = 1 - 50 ASCII characters.
Programming Programming Numbers The following information provides the programming numbers for colors, fonts, and borders. Colors can be used to set the colors on buttons, sliders, and pages. The lowest color number represents the lightest color-specific display; the highest number represents the darkest display. For example, 0 represents light red, and 5 is dark red. RGB Triplets and Names For Basic 88 Colors RGB Values for all 88 Basic Colors Index No.
Programming RGB Values for all 88 Basic Colors (Cont.) Index No.
Programming Font Styles And ID Numbers Font styles can be used to program the text fonts on buttons, sliders, and pages. The following chart shows the default font type and their respective ID numbers generated by TPDesign4.
Programming TPD4 Border Styles by Name (Cont.) 108 No. Border styles No.
Programming TPD4 Border Styles by Name (Cont.) No. Border styles No.
Programming "^" Button Commands (Cont.) ^BAT Syntax: Append non-unicode text. Variable: "'^BAT-,
Programming "^" Button Commands (Cont.) ^BCF Only if the specified fill color is not the same as the current color. Set the fill color to the specified color. Note: Color can be assigned by color name (without spaces), number or R,G,B value (RRGGBB or RRGGBBAA). Syntax: "'^BCF-,
Programming "^" Button Commands (Cont.) ^BFB ONLY works on General-type buttons. Set the feedback Syntax: type of the button. "'^BFB-,'" Variable: variable text address range = 1 - 4000. feedback type = (None, Channel, Invert, On (Always on), Momentary, and Blink). Example: SEND_COMMAND Panel,"'^BFB-500,Momentary'" Sets the Feedback type of the button to 'Momentary'. ^BIM Syntax: "'^BIM-,'" Set the input mask for the Variable: specified address.
Programming "^" Button Commands (Cont.) ^BMC Button copy command. Copy attributes of the source button to all the destination buttons. Note that the source is a single button state. Each state must be copied as a separate command. The section represents what attributes will be copied. All codes are 2 char pairs that can be separated by comma, space, percent or just ran together.
Programming "^" Button Commands (Cont.) ^BMF Set any/all button parameters by sending embedded codes and data. Syntax: "'^BMF-,
Programming "^" Button Commands (Cont.) ^BMF (Cont.) ’%GI’ = Set the bargraph invert/noninvert or joystick coordinate (0,1,2,3). ^GIV section on page 122 more information. ’%GU’ = Set the bargraph ramp up time in intervals of 1/10 second. ’%GD’ = Set the bargraph ramp down time in 1/10 second. ’%GG = Set the bargraph drag increment. Refer to the ^GDI command on page 122 for more information.
Programming "^" Button Commands (Cont.) ^BMI Set the button mask image. Mask image is used to crop a borderless button to a non-square shape. This is typically used with a bitmap. Syntax: "'^BMI-,
Programming "^" Button Commands (Cont.) ^BNC Syntax: Clear current TakeNote annotations. Variable: "'^BNC-,'" variable text address range = 1 - 4000. command value = (0= clear, 1= clear all). Example: SEND_COMMAND Panel,"'^BNC-973,0'" Clears the annotation of the TakeNote button with variable text 973. ^BNN Set the TakeNote network name for the specified Addresses. Syntax: "'^BNN-,'" Variable: variable text address range = 1 - 4000.
Programming "^" Button Commands (Cont.) ^BOR Set a border to a specific border style associated with a border value for those buttons with a defined address range. Refer to the Border Styles and Programming Numbers table on page 107 for more information. Syntax: "'^BOR-,'" Variable: variable text address range = 1 - 4000. border style name = Refer to the Border Styles and Programming Numbers table on page 107. border value = 0 - 41.
Programming "^" Button Commands (Cont.) ^BSF Set the focus to the text area. Note: Select one button at a time (single variable text address). Do not assign a variable text address range to set focus to multiple buttons. Only one variable text address can be in focus at a time. Syntax: "'^BSF-,'" Variable: variable text address range = 1 - 4000. selection value = Unselect = 0 and select = 1.
Programming "^" Button Commands (Cont.) ^BVN Syntax: SEND_COMMAND ,"'^BVN-,'" Set the computer control remote Variables: host for the variable text address range = 1 - 4000. specified address. remote host = 1 - 50 ASCII characters. Example: SEND_COMMAND Panel,"'^BVN-500,191.191.191.191'" Sets the remote host to '191.191.191.191' for the specific computer control button.
Programming "^" Button Commands (Cont.) ^DPF Syntax: Delete page flips from button if it already exists. Variable: "'^DFP-,,'" variable text address range = 1 - 4000.
Programming "^" Button Commands (Cont.) ^GDI Syntax: Change the bargraph drag increment. Variable: "'^GDI-,'" variable text address range = 1 - 4000. bargraph drag increment = The default drag increment is 256. Example: SEND_COMMAND Panel,"'^GDI-7,128'" Sets the bargraph with variable text 7 to a drag increment of 128. ^GIV Invert the joystick axis to move the origin to another corner.
Programming "^" Button Commands (Cont.) ^GRU Change the bargraph ramp-up time in 1/10th of a second. Syntax: "'^GRU-,'" Variable: variable text address range = 1 - 4000. bargraph ramp up time = In 1/10th of a second intervals. Example: SEND_COMMAND Panel,"'^GRU-500,100'" Changes the bargraph ramp up time to 10 seconds. ^GSC A user can also assign the color by Name and R,G,B value (RRGGBB or RRGGBBAA). Change the bargraph slider color or joystick cursor color.
Programming "^" Button Commands (Cont.) ^IRM Set the IR channel. Pulse the given IR channel for onTime in tenths of seconds. Delay offTime in tenths of a second before the next IR pulse is allowed. ^IRM allows the command itself to specify the port number. ^IRM is needed because commands programmed on the panel itself can only be sent to a single port number. (currently this is defined as 1 only). Note: The port number of the IR will be the port number assigned in TPD4.
Programming "^" Button Commands (Cont.) ^JST The alignment of 0 is followed by ',,'. The left and top coordinates are relative to the upper left corner of the button. Set text alignment using a Syntax: numeric keypad "'^JST-,
Programming "^" Button Commands (Cont.) ^TEF The Text Effect is specified by name and can be found in TPD4. Set the text effect. Syntax: "'^TEF-,
Programming Miscellaneous MVP Strings The following two strings are sent by the MVP panel back to the communicating Master: MVP Strings to Master undock This is sent to the target Master when the MVP is undocked. • If the panel has no information within the User Access Passwords list, ’none’ is sent as a user. • If the undock button on the Protected Setup page is used, ’setup’ is sent as a user. • This string can be disabled from within the firmware setup pages.
Programming Text Effects Names The following is a listing of text effects names associated with the ^TEF command on page 126.
Programming { Send_String Send_String Send_String Send_String Send_String Send_String Send_String 0,"'ButtonGet Id=',ITOA(CUSTOM.ID),' Type=',ITOA(CUSTOM.TYPE)" 0,"'Flag =',ITOA(CUSTOM.FLAG)" 0,"'VALUE1 =',ITOA(CUSTOM.VALUE1)" 0,"'VALUE2 =',ITOA(CUSTOM.VALUE2)" 0,"'VALUE3 =',ITOA(CUSTOM.VALUE3)" 0,"'TEXT =',CUSTOM.TEXT" 0,"'TEXT LENGTH =',ITOA(LENGTH_STRING(CUSTOM.
Programming Button Query Commands (Cont.) ?BCF Syntax: Get the current fill color. Variable: "'?BCF-,
Programming Button Query Commands (Cont.) ?BMP Syntax: Get the current bitmap name. Variable: "'?BMP-,
Programming Button Query Commands (Cont.) ?BRD Syntax: Get the current border name. Variable: "'?BRD-,
Programming Button Query Commands (Cont.) ?FON Syntax: Get the current font index. Variable: "'?FON-,
Programming Button Query Commands (Cont.) ?JSB Syntax: Get the current bitmap justification. Variable: "'?JSB-,
Programming Button Query Commands (Cont.) ?JST Syntax: Get the current text justification. Variable: "'?JST-,
Programming Button Query Commands (Cont.) ?TEF Syntax: Get the current text effect name. Variable: "'?TEF-,
Programming Panel Runtime Operations Serial Commands are used in Terminal Emulator mode. These commands are case insensitive. Panel Runtime Operation Commands ABEEP Syntax: Output a single beep even if beep is Off. Example: "'ABEEP'" SEND COMMAND Panel,"'ABEEP'" Outputs a beep of duration 1 beep even if beep is Off. ADBEEP Syntax: Output a double beep even if beep is Off. Example: "'ADBEEP'" SEND COMMAND Panel,"'ADBEEP'" Outputs a double beep even if beep is Off.
Programming Panel Runtime Operation Commands (Cont.) @AKP Pop up the keypad icon and initialize the text string to that specified. Keypad string is set to null on power up and is stored until power is lost. The Prompt Text is optional. Syntax: "'@AKP-;'" Variables: initial text = 1 - 50 ASCII characters. prompt text = 1 - 50 ASCII characters.
Programming Panel Runtime Operation Commands (Cont.) PKEYP Present a private keypad. Pops up the keypad icon and initializes the text string to that specified. Keypad displays a '*' instead of the numbers typed. The Prompt Text is optional. Syntax: "'PKEYP-'" Variables: initial text = 1 - 50 ASCII characters. Example: SEND COMMAND Panel,"'PKEYP-123456789'" Pops up the Keypad and initializes the text string '123456789' in '*'. @PKP Present a private keypad.
Programming Panel Runtime Operation Commands (Cont.) @TKP Present a telephone keypad. Pops up the keypad icon and initializes the text string to that specified. The Prompt Text is optional. Syntax: "'@TKP-;'" Variables: initial text = 1 - 50 ASCII characters. prompt text = 1 - 50 ASCII characters. Example: SEND COMMAND Panel,"'@TKP-999.222.1211;Enter Phone Number'" Pops-up the Keypad and initializes the text string '999.222.1211' with prompt text 'Enter Phone Number'.
Programming Input Commands These Send Commands are case insensitive. Input Commands ^CAL Syntax: Put panel in calibration mode. Example: "'^CAL'" SEND COMMAND Panel,"'^CAL'" Puts the panel in calibration mode. ^KPS Syntax: Set the keyboard passthru. Variable: "'^KPS-'" pass data: = Disables the keyboard. 0 = Pass data to G4 application (default). This can be used with VPC or text areas. 1 - 4 = Not used. 5 = Sends out data to the Master.
Programming Embedded codes The following is a list of G4 compatible embedded codes: Embedded Codes 142 Decimal numbers Hexidecimal values Virtual keystroke 8 ($08) Backspace 13 ($0D) Enter 27 ($1B) ESC 128 ($80) CTRL key down 129 ($81) ALT key down 130 ($82) Shift key down 131 ($83) F1 132 ($84) F2 133 ($85) F3 134 ($86) F4 135 ($87) F5 136 ($88) F6 137 ($89) F7 138 ($8A) F8 139 ($8B) F9 140 ($8C) F10 141 ($8D) F11 142 ($8E) F12 143 ($8F) Num Lock
Programming Panel Setup Commands These commands are case insensitive. Panel Setup Commands @PWD @PWD sets the level 1 password only. Set the page flip password. Syntax: "'@PWD-'" Variables: page flip password = 1 - 50 ASCII characters. Example: SEND COMMAND Panel,"'@PWD-Main'" Sets the page flip password to 'Main'. ^PWD Password level is required and must be 1 - 4. Set the page flip password.
Programming Dynamic Image Commands The following table describes Dynamic Image Commands. Dynamic Image Commands ^BBR Set the bitmap of a button to use a particular resource. Syntax: "'^BBR-,
Programming Dynamic Image Commands (Cont.) ^RMF Modifies any and all resource parameters by sending embedded codes and data. Modify an existing resource. Since the embedded codes are preceded by a '%' character, any '%' character contained in the URL must be escaped with a second '%' character (see example). The file name field (indicated by a %F embedded code) may contain special escape sequences as shown in the ^RAF, ^RMF - Embedded Codes section on page 145.
Programming ^RAF, ^RMF - Embedded Codes (Cont.) Parameter Embedded Code Description refresh ’%R ’ The number of seconds between refreshes in which the resource is downloaded again. Refreshing a resource causes the button displaying that resource to refresh also. newest ’%N <0-1>’ The default value is 0 (only download the resource once). Set the newest file. A value of 1 means that only the most recent file matching the pattern is downloaded.
Programming Intercom Commands The following is a list of Intercom Commands: Intercom Commands ^MODEL? Panel model name. If the panel supports intercom hardware it will respond with its model Sets model name. name as shown in the response below. Older hardware or newer hardware that has intercom support disabled with not respond to this command. Syntax: SEND_COMMAND ,"'^MODEL?'" Variables: None.
Programming Intercom Commands (Cont.) ^ICM-TALK Intercom modify command. For backwards compatibility both versions are supported. ^ICM-LISTEN In this release, however, the TALK and LISTEN sub commands are ignored. The microphone and/or speaker are activated based on the initial mode value of the intercom start command and the audio data packet flow is started upon receipt of this command by the panel. Intercom modify command. Syntax: SEND_COMMAND ,"'^ICM-TALK'" Variables: None.
Programming SIP Commands The following table lists and describes SIP commands that are generated from the touch panel. SIP Commands ^PHNAUTOANSWER Syntax: "'^PHN-AUTOANSWER, '" Provides the state Variable: of the state = 0 or 1 (off or on) auto-answer Example: feature. SEND_COMMAND Panel,"'^PHN-AUTOANSWER, 1'" ^PHN-CALL Provides call progress notification for a call. Syntax: "'^PHN-CALL, , '" Variable: status = CONNECTED, DISCONNECTED, TRYING, RINGING, or HOLD.
Programming SIP Commands (Cont.) ^PHNMSGWAITING Indicates the number of messages waiting in the user’s voice mail box. Syntax: "'^PHN-MSGWAITING, , , , , '" Variable: messages = 0 or 1 (1 indicates new messages) new message count = The number of new messages. old message count = The number of old messages. new urgent message count = The number of new messages marked urgent.
Programming SIP Commands (Cont.) ?PHNAUTOANSWER The panel responds with the ^PHN-AUTOANSWER, message. Syntax: Queries the state of the autoanswer feature. Example: ^PHN-CALL Syntax: Calls the provided number. Variable: "’?PHN-AUTOANSWER’" SEND_COMMAND Panel,"'?PHN-AUTOANSWER'" "’^PHN-CALL, ’" number = The provided phone number Example: SEND_COMMAND Panel,"'^PHN-CALL, 2125551000'" ^PHN-DTMF Syntax: Sends DTMF codes.
Programming SIP Commands (Cont.) ^PHNTRANSFER Syntax: Transfers the call to the provided number. Variable: "’^PHN-TRANSFER, , ’" connection id = The identifying number of the connection number = The number to which you want to transfer the call. Example: SEND_COMMAND Panel,"'^PHN-TRANSFER, 1, 2125551000'" The following table lists and describes SIP setup commands. Using any of these commands causes the current user to go offline.
Programming SIP Setup Commands (Cont.) ^PHN-SETUPUSERNAME Syntax: Sets the user name for authentication with the proxy server. Variable: "’^PHN-SETUP-USERNAME,’" username = The user name (usually the phone extension) Example: SEND_COMMAND Panel,"’^PHN-SETUP-USERNAME,6003’" MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.
Programming 154 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.
Battery Life and Replacement Battery Life and Replacement Overview The battery powering the MVP-5200i is designed for upwards of 300 deep discharge rechargings. Regular shallow rechargings will extensively increase expected battery life, and the device should be stored in either the Table Charging Station or the Wall Charging Station when not in use to keep it at an optimum charge. The battery has reached its effective end of life after it can no longer hold more than a 70 percent charge.
Battery Life and Replacement MVP-BP-5X Battery Pack (FG5966-27) Specifications Dimensions: 4 1/8” x 2 1/2” x 3/8” (10.48 cm x 6.35 cm x 0.95 cm) Weight: 0.35 lbs (158.
Battery Life and Replacement Battery Replacement The touch panel's battery is intended to last the life of the device, but in cases where the battery has reached its effective end of life, it may be replaced with the MVP-BP-5X Battery Pack Kit (FG5966-27). READ THESE INSTRUCTIONS FIRST! To minimize the risk of damage to the battery during installation, all replacement batteries come in a protective metal cover. This cover cannot be removed from the battery.
Battery Life and Replacement Battery Connector FIG. 82 Battery installation and connection diagram Remove the Old Battery Peel the hinge cover film from the hinges on either side of the battery before removing the battery. If the battery is attached to the interior of the device with adhesive tape, carefully pry the battery free. DO NOT use sharp or edged objects to pry the battery free, as these may damage the battery or the device.
Battery Life and Replacement When reassembling the device, take especial care not to pinch, puncture, or damage the battery. Do not force the rear plate onto the device, as this can damage the device. 4. Insert the five screws and replace the rubber feet atop the two upper screws, using the replacement rubber feet and bottom label included in the Battery Pack Kit (FIG. 5). Rubber feet Upper screws Back plate Bottom label Bottom screws Bottom screw holes Speaker Front of MVP-5200i FIG.
Battery Life and Replacement 160 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.
Appendix A: Text Formatting Appendix A: Text Formatting Text Formatting Codes for Bargraphs/Joysticks Text formatting codes for bargraphs provide a mechanism to allow a portion of a bargraphs text to be dynamically provided information about the current status of the level (multistate and traditional). These codes are entered into the text field along with any other text.
Appendix A: Text Formatting Text Area Input Masking Text Area Input Masking may be used to limit the allowed/correct characters that are entered into a text area. For example, in working with a zip code, a user could limit the entry to a max length of only 5 characters; with input masking, this limit could be changed to 5 mandatory numerical digits and 4 optional numerical digits. A possible use for this feature is to enter information into form fields.
Appendix A: Text Formatting Input Mask Ranges These ranges allow a user to specify the minimum and maximum numeric value for a field. Only one range is allowed per field. Using a range implies a numeric entry ONLY. Input Mask Ranges Character Meaning [ Start range ] End range | Range Separator An example from the above table: [0|255] This allows a user to enter a value from 0 to 255.
Appendix A: Text Formatting When data overflows from a numerical field, the overflow value is added to the previous field on the chain if the overflow character was specified. In the above example, if the overflow flag was set, the first example will place the "1" into the previous logical field and the second example will place "12" in the previous logical field.
Appendix A: Text Formatting Other used escape sequences include: Escape Sequences Sequence Panel Information $DV Device Number $SY System Number $IP IP Address $HN Host Name $MC Mac Address $ID Neuron ID $PX X Resolution of current panel mode/file $PY Y Resolution of current panel mode/file $BX X Resolution of current button $BY Y Resolution of current button $BN Name of button $ST Current state $AC Address Code $AP Address Port $CC Channel Code $CP Channel Port $LC Level
Appendix A: Text Formatting Complex Script Support In many cases, a user needs a touch panel user interface that utilizes a font applicable to the area for which its use is intended, and to accomplish this without needing to resort to images of properly formed text. This includes proper rendering of right-to-left languages such as, but not limited to, Arabic, Hebrew, Thai and Devangari (FIG. 85). Both the MVP-5200i and TPDesign4 (v3.
Appendix A: Text Formatting For more information on TPDesign4 and its complex script support, please refer to the TPDesign4 (v3.0 or higher) Operation Reference Guide, available at www.amx.com. MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.
Appendix A: Text Formatting 168 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.
Appendix B: Wireless Technology Appendix B: Wireless Technology Overview of Wireless Technology 802.11b/2.4 GHz and 802.11a/5 GHz are the two major WLAN standards and both operate using radio frequency (RF) technology. Together the two standards are together called Wi-Fi and operate in frequency bands of 2.4 GHz and 5 GHz respectively. The 802.11b specification was the first to be finalized and reach the marketplace. The actual throughput obtained from an 802.
Appendix B: Wireless Technology Terminology 802.1x IEEE 802.1x is an IEEE standard that is built on the Internet standard EAP (Extensible Authentication Protocol). 802.1x is a standard for passing EAP messages over either a wired or wireless LAN. Additionally, 802.1x is also responsible for communicating the method with which APs and wireless users can share and change encryption keys. This continuous key change helps resolve any major security vulnerabilities native to WEP.
Appendix B: Wireless Technology To resolve problems with WEP, the Wi-Fi Alliance released WPA (FIG. 87), which integrated 802.1x, TKIP and MIC. Within the WPA specifications, the RC4 cipher engine was maintained from WEP. RC4 is widely used in SSL (Secure Socket Layer) to protect internet traffic. FIG. 87 WPA Overview WPA2 Also know as IEEE 802.11i, this is an amendment to the 802.11 standard specifying security mechanisms for wireless networks. The 802.
Appendix B: Wireless Technology EAP Authentication EAP (Extensible Authentication Protocol) is an Enterprise authentication protocol that can be used in both a wired and wireless network environment. EAP requires the use of an 802.1x Authentication Server, also known as a RADIUS server. Although over 40 different EAP methods are currently defined, the current internal Modero 802.
Appendix B: Wireless Technology EAP Communication Overview EAP Authentication goes a step beyond just encrypting data transfers, but also requires that a set of credentials be validated before the client (panel) is allowed to connect to the rest of the network (FIG. 89). Below is a description of this process. It is important to note that no user intervention is necessary during this process. It proceeds automatically based on the configuration parameters entered into the panel. LAN 802.
Appendix B: Wireless Technology Configuring Modero Firmware via the USB Port The MVP-5200i needs to be configured to connect with a PC to transfer firmware via the mini-USB port. To configure the touch panel: Prepare NetLinx Studio For Communication Via the USB Port 1. From the Start menu in Windows XP, open the Network Connections dialog (Start > Settings > Network Connections > Local Area Connection). 2.
Appendix B: Wireless Technology AMX Certificate Upload Utility The Certificate Upload utility gives you the ability to compile a list of target touch panels, select a pre-obtained certificate (uniquely identifying the panel), and then upload that file to the selected panel. This application must be run from a local machine and should not be used from a remote network location. This application ensures that a unique certificate is securely uploaded to a specific touch panel.
Appendix B: Wireless Technology 11. Once the list is complete, click on the File drop-down menu and select the Save option. This launches a Save dialog to assign a name to the current list of addresses and then save the information as a TXT (text) file to a known location. This application must be run from a local machine and should not be used from a remote network location. 12. Select the target devices to be uploaded with the selected certificate.
Appendix C: Troubleshooting Appendix C: Troubleshooting Overview This section describes the solutions to possible hardware/firmware issues that could arise during the common operation of a Modero touch panel. Panel Doesn’t Respond To Touches Symptom: The device either does not respond to touches on the touch screen or does not register the touch as being in the correct area of the screen. If the screen is off: The device may be in Standby Mode. Press and hold the display screen to wake up the panel.
Appendix C: Troubleshooting MVP-5200i Isn’t Appearing In The Online Tree Tab 1. Verify that the System number is the same on both the NetLinx Project Navigator window and the System Settings page on the device. 2. Verify the proper NetLinx Master IP and connection methods entered into the Master Connection section of the System Settings page. MVP Can’t Obtain a DHCP Address In requesting a DHCP Address, the DHCP Server can take up to a few minutes to provide the address. 1.
Appendix C: Troubleshooting Panel Behaves Strangely After Downloading A Panel File Or Firmware Symptom: After downloading a panel file or firmware to a G4 device, the panel behaves strangely. If the panel already contains a large enough file, subsequent downloads will take up more space than is available and could often corrupt the Compact Flash. The demo file that typically ships with G4 panels is one such file. Symptoms include: Having to repeat the download.
Appendix C: Troubleshooting 180 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.
Appendix C - Troubleshooting MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.
AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX. AMX reserves the right to alter specifications without notice at any time. ©2012 8/2012 It’s Your World - Take Control™ 3000 RESEARCH DRIVE, RICHARDSON, TX 75082 USA • 800.222.0193 • 469.624.8000 • 469-624-7153 fax • 800.932.6993 technical support • www.amx.
