Enclosure Worksheet Guide Radia Lighting Lighting Control Document ID: 043-004-2440 Last Revised: 6/15/2006
AMX Limited Warranty and Disclaimer AMX warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX, with the following exceptions: • Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay components that are warranted for a period of one (1) year.
Lighting Sales Information AMX Lighting products are guaranteed to switch on and off any load that is properly connected to our lighting products, as long as the AMX Lighting products are under warranty. AMX Corporation does guarantee the control of dimmable loads that are properly connected to our lighting products. That includes loads correctly chosen, sized and attached to our dimmers or switches under normal power conditions.
Table of Contents Table of Contents AMX Lighting - Enclosure Worksheet Guide ......................................................1 Worksheet Layout..................................................................................................... 2 Cells ................................................................................................................................ 2 What You Must Specify ...................................................................................................
Table of Contents ii AMX Lighting - Enclosure Worksheet Guide
AMX Lighting - Enclosure Worksheet Guide AMX Lighting - Enclosure Worksheet Guide The AMX Lighting Enclosure Worksheet, found on page 11 lets you specify the contents of an AMX Lighting Enclosure. The best resource for designing a Radia lighting system is the Enclosure Worksheet. Use this worksheet to configure the hardware for each Radia enclosure. Larger systems will use multiple Enclosure Worksheets. The Enclosure Worksheet is used to design, build, and deliver a complete working Radia Lighting System.
AMX Lighting - Enclosure Worksheet Guide Worksheet Layout The worksheet is made of columns and rows of information and is divided into a top, middle, and bottom section. Each Worksheet contains Rows and Columns. FIG. 2 shows the layout of a sample Worksheet and their sections.
AMX Lighting - Enclosure Worksheet Guide Click on arrow next to a drop-down field in a cell to reveal the menu. FIG. 3 Sample drop-down cell Highlight the field with a mouse click and it will darken the color, then use the keyboard to type in text. FIG. 4 Sample text cell What You Must Specify There are three items that you must specify with each worksheet: 1. An enclosure 2. A controller and 3.
AMX Lighting - Enclosure Worksheet Guide Control cards always take up a space, usually Slot 1. If a control card is used in Slot 1, then do not place a module also in Slot 1, even though the program allows you to. (There is no real-time error correction with the template, and it will allow for certain non-valid configurations.) If an RDD-DM4 is placed in Slot 1 it takes up two module spaces and will, therefore, occupy Slot 2 as well.
AMX Lighting - Enclosure Worksheet Guide • blank • RDM-MDM • RDD-DM4/120 • RDM-FDB • RDD-DM4/240 • RDM-2FDB • RDD-DM4/277 • RDM-3FDB • RDD-DM6/120 • RDM-HFDB • RDD-DM6/240 • RDM-DC • RDD-DM6/277 • RDM-2DC • RDM-INC • RDM-3DC • RDM-2INC • RDM-HDC • RDM-INC50 MODULE Switches (right) uses a drop-down menu containing the switching choices listed below: • blank • RDM-DPSM • RDM-MDM • RDM-ZC • RDM-SWM • RDM-2ZC • RDM-2SWM • RDM-ZC50 • RDM-3SWM • RDA-EFP • RDM-HSW • RDA-PSM • RDM-2H
AMX Lighting - Enclosure Worksheet Guide PROlink PACK #: This drop-down menu is used to specify the Radia Pack number from 1 - 10. These are the only valid choices. The default pack number for Slot 1 is #1. The pack numbers sequentially start at 1. If the pack number is unknown, then the field can be left alone using the default #1 or set to a blank using the drop down menu. When using multiple packs in a PROlink system make sure the other Enclosure Worksheets have the AXlink Device number identified.
AMX Lighting - Enclosure Worksheet Guide Curve: Curves are used to adjust the performance of the dimming control. The standard dimming curve is #1 and the switching curve is an 'N'. Some modules require a specific curve. This cell allows the designer to specify a particular curve applied to a dimmer. Control cards/ Accessories are not assigned curves. Assigning curves to unused dimmers is optional.
AMX Lighting - Enclosure Worksheet Guide Volts: Use this cell to enter the voltage of the load connected to the dimmer. This is important because some local electrical codes do not allow mixing of voltages in a single enclosure. Local codes may also require use of a separate container for each voltage device used on the premises. Some dimming modules are phase dependent, and mixed voltages will cause poor dimming performance when the controller is out of phase with the supply voltage to the dimmer.
AMX Lighting - Enclosure Worksheet Guide Job Information: Use these cells to post information on the dealer, the job, and order numbers. The job information box uses a text fields in rows that allow up to (32) characters, as listed below • Dealer ID (must be 5 digit number) • Site • Today's date (automatically inserted) • SO# • Dealer • PO# • Job Name Initials Notes: Use this field to place any notes about the system.
Lighting 8 OFF * * * * * * * Radia DEALER ID DEALER JOB NAME SITE SO# QUOTE# DATE: REVISION: Quote #: CURVE ENC 1 2 3 4 5 6 7 8 SERIAL NUMBERS PO# DATE TYPE Radia Enclosure Worksheet DIM # DESCRIPTION / ZONE PHONE: 1 7 * ON * * * * * * AMX Corp.
AMX Corp.
It’s Your World - Take Control™ 3000 RESEARCH DRIVE, RICHARDSON, TX 75082 USA • 800.222.0193 • 469.624.8000 • 469-624-7153 fax • 800.932.6993 technical support • www.amx.com 043-004-2440 6/06 ©2006 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX. AMX reserves the right to alter specifications without notice at any time.
