.17inch 21.0 2 in 18.8 ch 9 in ch ATTACH THE CLAMPS TO THE METAL TO THE METAL BASE OF THE COOKTOP. There are holes on the 4 sides of the metal of the metal base through which you can fit the brackets. h 0 inc 30.0 h 0 inc 28.
General safety regulations 1 Installation 4 Technical Specification Cooktop Features 3 7 Before using your new induction hob 8 Cleaning and maintenance 13 Warranty 16 Using the Induction cooktop Trouble Shooting 9 14 MADE IN CHINA Manufacturer:Zhongshan Fansheng Electric Appliances Co., Ltd ADD:10th Building No.268 Dongfu 3rd RD Suicheng Village, Dongfeng Zhongshan, Guangdong China Contact：Emily Tel:+1（838）910 8317 E-Mail：info@iamzchef.
Chapter I.
2
AC 240V~ 60Hz 10600W AC 208V~ 60Hz 9200W 3
Selection of installation equipment 2.17inch 21.0 30.0 ch 18.8 h 0 inc 2 in ch ATTACH THE CLAMPS TO THE METAL TO THE METAL BASE OF THE COOKTOP. There are holes on the 4 sides of the metal of the metal base through which you can fit the brackets. 4 h 0 inc 28.
Ventilation and safety distances cooktop Wiring Instructions 5
6
Cooktop Features Throughout this manual, features and appearance may vary from your model. ① ② ③ ① 2000W ② 3200W ③ 2000W ④ 2700W ⑤ 2700W ⑥ Ceramic Glass ⑦ Control Panel ④ ⑦ Slider control ⑥ ⑤ Pause button Safety lock 7 www.iamzchef.com Email: info@iamzchef.
Before using your new induction hob Using the Touch Controls The sensor buttons respond to touch, so you do not need to press them. Touch the sensors with the bottom side of your top phalanx but not with your fingertip (see figure below). You will hear a beep after each effective input. Always keep the touch control clean and dry. Cooking utensils and cloths should not cover the touch control. A thin water film may already complicate operating the sensors.
Using the Induction cooktop How to Start? 1.When the power cord is successfully connected, the induction cooktop will emit a beep sound once, the display screen will flash once.The appliance is in stand-by mode now 2.Place a cookware on the desired cooking zone. Always keep the bottom of the cookware as well as the cooking zone clean and dry. 3.Touch the ON/OFF button of selected cooking zone,the display indicates -. 4.Set the power level with the + or - or Boost button.
How to stop cooking? Under working status, press ON/OF button of selected cooking zone , the selected zone would stop heating. Beware of hot surfaces When the surface temperature exceeds 55°C/131℉ an "H" will be displayed indicating that the cooking zone is too hot to touch.It will disappear when the surface has cooled down to a safe temperature. It can also be used as an energy saving function if you want to heat further pans, use the hotplate that is still hot.
Timer Function You can program a cooking time between 1 and 99 minutes after setting the power. 1.Press the Timer button -The corresponding indicator light of selected working zone flashes - ”00” (default time) appears in the display 2. Set the desired time using the + and - button . -Touch +/- button once to increase/decrease the time by 1 minute. -Hold +/- button to increase/decrease the time by 10 minutes. 3.When finished the setting, the count-down of the set time starts.
Setting the timer to turn more than one cooking zone off Ee.g. zone 1# setting time of 3 minutes, zone 2# setting time of 6 minutes, the timer indicator shows “3”. (set to 6 minutes) (set to 3 minutes) NOTE: The flashing red dot next to power level indicator means the timer indicator is showing time of the heating zone. If you want to check the set time of other heating zone, touch the heating zone selection control. The timer will indicate its set time.
Cleaning and maintenance ●Disconnect plug and wait until the unit is cooled down completely. ●If the pots/pans are used without being cleaned, discoloration or cooked on stains may occur. ●Do not use benzene, thinner, scrubbing brush or polishing powder to clean the cooktop. ●Do not use any flammable, acid alkaline materials or substances near the cooktop, as this may reduce the service life of the cooktop and lead to deflagration when the cooktop is turned on.
Trouble Shooting If you encounter a problem, it often will merely be something minor. Before you call customer service, review the charts on the following pages first and you may not to call for service. If an error occurs in the control operation, a fault code will flash in the display .Record the error code and call for service. CAUTION! Repairs should only be done by an authorized servicer.
Pans do not become hot and appears in the display. The induction hob or a cooking zone has turned itself off unexpectedly, a tone sounds and an error code is displayed (typically alternating with one or two digits in the cooking timer display). Code The induction hob cannot detect the pan because it is not suitable for induction cooking. The induction hob cannot detect the pan because it is too small for the cooking zone or not properly centred on it. Use cookware suitable for induction cooking.
16 www.iamzchef.com Email: info@iamzchef.
