Datasheet

ManualsBrandsANAG VISION ManualsDisplaysGraphical Display Module, 5V, Yellow/Green LED, 128 x 64 Resolution, N/A

ANAG VISION

AV128641

ANAG VISION

128 x 64 Graphic

Verfügbar STN:  gelb-grün LED  blau negativ

   positiv LED gelb LED weiß

CONRAD Best.-Nr: 181677  181682

This data sheet is for reference only.

The color of the disply may vary slightly depending on different production lots and ambient light. We reserve the right to changes and improvments without prior notice.

Mechanical Data

Item Standard Value Unit

Module Size 93.0 x 70.0 mm

Viewing Area

72.0 x 40.0 mm

Dot Size 0.48 x 0.48 mm

0.52 x 0.52

Dot Pitch

Absolute Maximum Rating

Standard Value

Item Symbol

min. typ. max.

Unit

Vdd-Vss

4.5 5.0 5.5

VI -0.3 - - - Vdd

Vss=0V, Vdd=5.0V

Input Voltage

Supply Voltage

Pin Assignment

No. Symbol Function

Enable Signal H=>L

DB0 - DB7 Data Bus Line

A *

Power Supply for LED 0V

Vee

Negative Voltage Output

Power Supply (0V) Gnd

Power Supply (+5V)

Contrast Adjustment

R/W

Data Read/Write

7-14

CS1

Chip Select IC1

D/I

RST

Data/Instruction

Reset

CS2

Power Supply for LED +4.2V

Chip Select IC2

Built-in controller

(KS0107 - KS0108 or equivalent)

+5V power supply

NV built in

1/64 duty

ILED

LED weiß Voltage *

3.5 V

100

Electronical Characteristics

Standard Value

Item

Symbol

Condit.

min. typ. max.

Unit

Input Voltage

Supply Curent Idd

Vdd = +5V

0 °C

9.7 10.2

10.7

25 °C 8.9 9.9

50 °C 8.6 9.1 9.6

Recommended LC Driving

Voltage for Standard Temp.

Modules

Vdd-V0

LED Forward Voltage Vf

25 °C - - - 4.2 4.6

LED Forward Current If

25 °C - - - 300

0.3Vdd

600

VIO

H Level

L Level

0.7Vdd

Vss

Vdd

- - -

9.7

- - - - - -

Summary of content (9 pages)

PAGE 1
ANAG VISION AV128641 128 x 64 Graphic ° Built-in controller (KS0107 - KS0108 or equivalent) ° +5V power supply ° NV built in ° 1/64 duty Pin Assignment No. Symbol 1 2 3 4 5 6 7-14 15 16 17 18 19 20 Vss Vdd VO D/I __ R/W E DB0 - DB7 CS1 CS2 __ RST Vee A* K Absolute Maximum Rating Function Power Supply (0V) Gnd Power Supply (+5V) Contrast Adjustment Data/Instruction Data Read/Write Enable Signal H=>L Data Bus Line Chip Select IC1 Chip Select IC2 Reset Negative Voltage Output Power Supply for LED +4.
PAGE 2
ANAG VISION RY A N IMI L PRE KS0107/0108 or equ. PROGRAMMING INSTRUCTIONS FOR 128x64 BIT MAP TYPE LCD-MODULES Displa y c ont rol inst ruc t ion The LCD Module has built in the KS0107 (or equivalent type), an LCD driver LSI with 64 channel outputs for dot matrix liquid crystal graphic display systems. It generates the timing signal to control the 2 KS0108 (or equivalent type) which are the 64 channel ourput LCD driver LSIs for dot matrix liquid crystal graphic display systems.
PAGE 3
Contour Drawing, Block Diagram and Backlight Connection 4 5 6 7 8 R/W E 9 Q "6 "6 "6 RET Q % Q % % Q R/W E 4% % Q RST 4 % 128X64 DOT GRAPHIC MODULES PROGRAMMING PA G E : 2 O F 8
PAGE 4
Timing Characteristics 450 450 E R/W E R/W 128X64 DOT GRAPHIC MODULES PROGRAMMING PA G E : 3 O F 8
PAGE 5
Display Control Instructions Instruction DI R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Function 0 0 0 0 0 0 0 0 0 0 0 ON/OFF 0 B U S Y 0 0 ON/ R OFF E S E T 0 0 0 0 0 128X64 DOT GRAPHIC MODULES PROGRAMMING PA G E : 4 O F 8
PAGE 6
Detailed Explanation R/W 0 0 0 0 R/W 0 0 R/W 0 0 0 R/W 0 0 0 128X64 DOT GRAPHIC MODULES PROGRAMMING PA G E : 5 O F 8
PAGE 7
R/W 1 0 0 0 0 0 0 R/W 0 1 R/W 1 1 1 128X64 DOT GRAPHIC MODULES PROGRAMMING PA G E : 6 O F 8
PAGE 8
128X64 DOT GRAPHIC MODULES PROGRAMMING PA G E : 7 O F 8
PAGE 9
The intension of this document is to provide help if needed. It has been created with care, still the right for errors is reserved. With respect to any information carried out in this document, we take no warrenties, expressed or implied, including any warrenties of merchantability, the fitness for any particular purpose, infringement of any legal liability, responsibilty for the accuracy, the completeness and usefullness of any of these informations.