Low Cost 270 MHz Differential Receiver Amplifiers AD8129/AD8130 CONNECTION DIAGRAM High speed AD8130: 270 MHz, 1090 V/μs @ G = +1 AD8129: 200 MHz, 1060 V/μs @ G = +10 High CMRR 94 dB min, dc to 100 kHz 80 dB min @ 2 MHz 70 dB @ 10 MHz High input impedance: 1 MΩ differential Input common-mode range ±10.5 V Low noise AD8130: 12.5 nV/√Hz AD8129: 4.
Powered by TCPDF (www.tcpdf.org) IMPORTANT LINKS for the AD8129_8130* Last content update 08/23/2013 05:14 pm PARAMETRIC SELECTION TABLES DESIGN TOOLS, MODELS, DRIVERS & SOFTWARE Find Similar Products By Operating Parametersfor the AD8129 Find Similar Products By Operating Parametersfor the AD8130 Amplifiers for Video Distribution High Speed Amplifiers Selection Table Analog Filter Wizard 2.
AD8129/AD8130 TABLE OF CONTENTS Features .............................................................................................. 1 Theory of Operation ...................................................................... 32 Applications....................................................................................... 1 Op Amp Configuration ............................................................. 32 Connection Diagram .....................................................................
AD8129/AD8130 AD8129/AD8130 SPECIFICATIONS 5 V SPECIFICATIONS AD8129 G = +10, AD8130 G = +1, TA = 25°C, +VS = 5 V, −VS = 0 V, REF = 2.5 V, PD ≥ VIH, RL = 1 kΩ, CL = 2 pF, unless otherwise noted. TMIN to TMAX = −40°C to +125°C, unless otherwise noted. Table 1. Model Parameter DYNAMIC PERFORMANCE −3 dB Bandwidth Bandwidth for 0.
AD8129/AD8130 Model Parameter DC PERFORMANCE Closed-Loop Gain Error Open-Loop Gain Gain Nonlinearity Input Offset Voltage Input Offset Voltage vs. Supply Conditions Min VOUT = ±1 V, RL ≥ 150 Ω TMIN to TMAX VOUT = ±1 V VOUT = ±1 V ±0.25 20 86 250 0.2 2 TMIN to TMAX TMIN to TMAX +VS = 5 V, −VS = −0.5 V to +0.5 V −VS = 0 V, +VS = +4.5 V to +5.
AD8129/AD8130 ±5 V SPECIFICATIONS AD8129 G = +10, AD8130 G = +1, TA = 25°C, VS = ±5 V, REF = 0 V, PD ≥ VIH, RL = 1 kΩ, CL = 2 pF, unless otherwise noted. TMIN to TMAX = −40°C to +125°C, unless otherwise noted. Table 2. Parameter DYNAMIC PERFORMANCE −3 dB Bandwidth Bandwidth for 0.
AD8129/AD8130 Parameter DC PERFORMANCE Closed-Loop Gain Error Open-Loop Gain Gain Nonlinearity Input Offset Voltage Input Offset Voltage vs. Supply Conditions Min VOUT = ±1 V, RL ≥ 150 Ω TMIN to TMAX VOUT = ±1 V VOUT = ±1 V ±0.4 20 88 250 0.2 2 TMIN to TMAX TMIN to TMAX +VS = +5 V, −VS = −4.5 V to −5.5 V −VS = −5 V, +VS = +4.5 V to +5.
AD8129/AD8130 ±12 V SPECIFICATIONS AD8129 G = +10, AD8130 G = +1, TA = 25°C, VS = ±12 V, REF = 0 V, PD ≥ VIH, RL = 1 kΩ, CL = 2 pF, unless otherwise noted. TMIN to TMAX = −40°C to +85°C, unless otherwise noted. Table 3. Parameter DYNAMIC PERFORMANCE −3 dB Bandwidth Bandwidth for 0.
AD8129/AD8130 Parameter DC PERFORMANCE Closed-Loop Gain Error Open-Loop Gain Gain Nonlinearity Input Offset Voltage Input Offset Voltage vs. Supply Conditions Min VOUT = ±1 V, RL ≥ 150 Ω TMIN to TMAX VOUT = ±1 V VOUT = ±1 V ±0.8 20 87 250 0.2 2 TMIN to TMAX TMIN to TMAX +VS = +12 V, −VS = –11.0 V to −13.0 V −VS = −12 V, +VS = +11.0 V to +13.
AD8129/AD8130 ABSOLUTE MAXIMUM RATINGS Table 4. Rating 26.4 V Refer to Figure 4 −VS − 0.3 V to +VS + 0.3 V ±0.5 V ±6.2 V ±8.4 V −65°C to +150°C 300°C 150°C The power dissipated in the package (PD) is the sum of the quiescent power dissipation and the power dissipated in the package due to the load drive. The quiescent power is the voltage between the supply pins (VS) times the quiescent current (IS). The power dissipated due to the load drive depends upon the particular application.
AD8129/AD8130 TYPICAL PERFORMANCE CHARACTERISTICS AD8130 FREQUENCY RESPONSE CHARACTERISTICS G = +1, RL = 1 kΩ, CL = 2 pF, VOUT = 0.3 V p-p, TA = 25°C, unless otherwise noted. 6 3 VOUT = 0.3V p-p 2 VS = ±5V VS = ±2.5V 5 1 4 0 3 CL = 20pF VS = ±12V –2 –3 0 –1 –5 –2 1 10 FREQUENCY (MHz) 100 CL = 2pF –3 –4 400 Figure 5. AD8130 Frequency Response vs. Supply, VOUT = 0.3 V p-p 1 100 300 Figure 8. AD8130 Frequency Response vs. Load Capacitance 3 0.7 VOUT = 1V p-p RL = 1kΩ VS = ±2.
AD8129/AD8130 3 3 0 VS = ±5V –2 VS = ±12V –3 –3 –4 –5 1 10 FREQUENCY (MHz) 100 3 RF = RG = 250Ω –6 –7 400 G = +2 RL = 1kΩ 0.2 VS = ±2.5V 0.1 0 0 VS = ±12V –2 –0.1 –0.2 –0.4 –5 –0.5 02464-013 –4 –6 1 10 FREQUENCY (MHz) 100 VS = ±5V –0.3 VS = ±12V 02464-016 GAIN (dB) VS = ±5V –3 –0.6 –0.7 300 1 Figure 12. AD8130 Frequency Response vs. Supply, G = +2, VOUT = 0.3 V p-p 10 FREQUENCY (MHz) 100 Figure 15. AD8130 Fine Scale Response vs. Supply, G = +2, RL = 1 kΩ 0.
AD8129/AD8130 3 3 G = +2 2 RL = 150Ω VS = ±2.5V GAIN (dB) –1 –2 VS = ±12V –3 –1 –4 –5 10 FREQUENCY (MHz) 100 VS = ±5V, ±12V –6 –7 0.1 300 Figure 17. AD8130 Frequency Response vs. Supply, G = +2, RL = 150 Ω 1 FREQUENCY (MHz) 10 100 Figure 20. AD8130 Frequency Response vs. Supply, G = +5, G = +10, RL = 150 Ω 0.3 12 VOUT = 2V p-p 0dB = 1V rms 0.2 6 VS = ±2.5V 0.1 VS = ±5V OUTPUT VOLTAGE (dBV) 0 0 –0.1 VS = ±12V VS = ±2.5V –0.2 VS = ±5V, ±12V –0.3 –0.4 G = +10 G = +5 –0.
AD8129/AD8130 AD8129 FREQUENCY RESPONSE CHARACTERISTICS G = +10, RL = 1 kΩ, CL = 2 pF, VOUT = 0.3 V p-p, TA = 25°C, unless otherwise noted. 3 4 VOUT = 0.3V p-p VS = ±5V CL = 10pF 1 2 0 1 –1 GAIN (dB) VS = ±12V –2 –3 0 –5 –4 1 10 FREQUENCY (MHz) 100 CL = 2pF –2 –3 –7 CL = 5pF –1 –4 –6 CL = 20pF 3 VS = ±5V 02464-027 VS = ±2.5V 02464-024 GAIN (dB) 2 –5 –6 300 Figure 23. AD8129 Frequency Response vs. Supply, VOUT = 0.3 V p-p 1 10 FREQUENCY (MHz) 100 300 Figure 26.
AD8129/AD8130 3 0.8 RL = 150Ω VS = ±2.5V –1 0 VS = ±5V –2 VS = ±12V –3 0.2 0 –5 –0.2 –7 10 100 FREQUENCY (MHz) 499Ω/54.9Ω 909Ω/100Ω –0.2 –4 –6 SOIC μSOIC 2kΩ/221Ω 02464-033 GAIN (dB) 0.2 –0.4 –0.6 300 1 Figure 29. AD8129 Frequency Response vs. Supply, RL = 150 Ω 10 FREQUENCY (MHz) G = +20 VOUT = 0.3V p-p 2 100 300 Figure 32. AD8129 Fine Scale Response vs. SOIC and MSOP for Various RF/RG 0.2 3 2kΩ/221Ω 909Ω/100Ω 499Ω/54.9Ω 0.
AD8129/AD8130 3 3 G = +20 RL = 150Ω 2 1 1 0 VS = ±5V, ±12V GAIN (dB) –1 –2 –3 –1 –3 VS = ±2.5V –4 –4 VS = ±2.5V –6 –7 1 VS = ±5V –5 VS = ±12V 02464-036 –5 10 FREQUENCY (MHz) 100 –6 –7 300 0.1 1 FREQUENCY (MHz) 10 50 Figure 38. AD8129 Frequency Response vs. Supply, G = +50, G = +100, RL = 150 Ω Figure 35. AD8129 Frequency Response vs. Supply, G = +20, RL = 150 Ω 12 0.2 0dB = 1V rms VOUT = 2V p-p 6 VS = ±12V 0.1 0 G = +100 –0.2 G = +50 VS = ±2.5V –0.3 VS = ±5V –0.4 –0.
AD8129/AD8130 AD8130 HARMONIC DISTORTION CHARACTERISTICS RL = 1 kΩ, CL = 2 pF, TA = 25°C, unless otherwise noted. –51 –60 VOUT = 1V p-p VOUT = 1V p-p G = +1 VS = ±5V –57 G = +1 VS = ±12V –66 –63 –69 HD3 (dBc) HD2 (dBc) VS = ±12V –72 G = +1 –78 –75 VS = ±5V VS = ±12V –81 G = +1 VS = ±5V VS = ±12V –87 –84 1 10 G = +2 –99 40 10 1 FREQUENCY (MHz) 40 FREQUENCY (MHz) Figure 44. AD8130 Third Harmonic Distortion vs. Frequency Figure 41. AD8130 Second Harmonic Distortion vs.
AD8129/AD8130 –43 –46 VS = ±2.5V VS = ±2.5V fC = 5MHz –52 G = +2, HD3 G = +1, HD3 –49 –58 G = +1 VOUT = 2V p-p G = +2 –61 G = +1, HD2 –64 HD (dBc) HD2 (dBc) –55 G = +2, HD2 –70 G = +2, HD2 –76 –67 G = +2, HD3 –82 G = +2 –79 1 –88 02464-048 G = +1 VOUT = 1V p-p –94 40 10 0 FREQUENCY (MHz) VS = ±2.5V –54 G = +2 –72 G = +1 –78 G = +1 –84 G = +2 02464-049 HD3 (dBc) VOUT = 2V p-p –66 VOUT = 1V p-p –90 –96 1 10 1.0 1.5 2.0 2.5 Figure 49. AD8130 Harmonic Distortion vs.
AD8129/AD8130 AD8129 HARMONIC DISTORTION CHARACTERISTICS RL = 1 kΩ, CL = 2 pF, TA = 25°C, unless otherwise noted. –54 –51 VOUT = 1V p-p VOUT = 1V p-p –60 –57 G = +10, VS = ±12V –66 –69 HD3 (dBc) HD2 (dBc) –63 G = +10, VS = ±12V G = +10, VS = ±5V G = +10, VS = ±5V –72 –78 G = +20, VS = ±5V –75 –84 G = +20, VS = ±5V –87 10 FREQUENCY (MHz) 1 –90 02464-051 –81 –96 40 1 Figure 50. AD8129 Second Harmonic Distortion vs.
AD8129/AD8130 –44 –39 VS = ±2.5V G = +1 VOUT = 2V p-p VS = ±5V RL = 1kΩ fC = 5MHz –45 VOUT = 2V p-p –50 –51 DISTORTION (dBc) HD2 (dBc) –56 G = +20 –62 VOUT = 1V p-p –68 –57 –63 –69 HD2 –75 –74 1 10 FREQUENCY (MHz) –5 Figure 56. AD8129 Second Harmonic Distortion vs. Frequency –42 02464-060 –87 40 –4 –3 –2 –1 0 1 VCM (V) 2 3 –61 G = +1 fC = 5MHz –48 VOUT = 1V p-p –67 VOUT = 2V p-p HD2 VS = ±2.
AD8129/AD8130 –36 G = +10 VOUT = 2V p-p VS = ±5V RL = 1kΩ fC = 5MHz –42 VCM 200Ω –54 RL CL HD2 RG –72 HD3 –78 –5 –4 –3 –2 –1 0 1 2 3 4 RF MINI-CIRCUITS®: # T4-6T, fC ≤ 10MHz # TC4-1W, fC > 10MHz 5 VCM (V) G RF RG 1 2 10 20 0Ω 499Ω 2kΩ 2kΩ – 499Ω 221Ω 105Ω 02464-066 –66 Figure 65. AD8129/AD8130 Basic Distortion Test Circuit, VCM = 0 V, Unless Otherwise Noted Figure 62. AD8129 Harmonic Distortion vs. Common-Mode Voltage 100 –48 G = +10 fC = 5MHz –54 VOUT = 1V p-p VS = ±2.
–30 –40 –40 –50 –50 –60 –70 –80 VS = ±2.5V –100 –110 –120 10k 100k 1M FREQUENCY (Hz) 10M 100M 0 –10 POWER SUPPLY REJECTION (dB) 0 –20 –30 –40 –50 –60 VS = ±12V –80 VS = ±5V VS = ±2.5V –100 1k 10k 100k 1M FREQUENCY (Hz) 10M –50 –60 –70 VS = ±12V –80 POWER SUPPLY REJECTION (dB) –30 –40 –50 –60 VS = ±2.5V 02464-071 –80 100k 1M 10M 10k 100k 1M FREQUENCY (Hz) 10M 100M Figure 72. AD8129 Positive Power Supply Rejection vs. Frequency –10 10k VS = ±2.
AD8129/AD8130 80 100 30 PHASE + VOUT – 20 + 10 1kΩ – 100Ω 0 2pF 45 φM = 58° 10k 100k 1M FREQUENCY (Hz) 10M AD8129, G = +10 0 100M 300M Figure 74. AD8130 Open-Loop Gain and Phase vs. Frequency 80 180 135 60 50 90 40 PHASE VOUT 30 1kΩ 20 10 2pF 1kΩ 45 PHASE MARGIN (Degrees) GAIN 70 φM = 56° 1k 10k 100k 1M 10M FREQUENCY (Hz) 100M 0 300M 02464-076 VIN 0 1m 1k 10k 100k 1M FREQUENCY (Hz) 10M Figure 76. Closed-Loop Output Impedance vs.
AD8129/AD8130 AD8130 TRANSIENT RESPONSE CHARACTERISTICS G = +1, RL = 1 kΩ, CL = 2 pF, VS = ±5 V, TA = 25°C, unless otherwise noted. VS = ±2.5V VOUT = 1V p-p VS = ±2.5V VS = ±5V VOUT = 0.2V p-p 5.00ns 50mV Figure 77. AD8130 Transient Response, VS = ±2.5 V, VOUT = 1 V p-p 5.00ns 02464-081 250mV 02464-078 VS = ±12V Figure 80. AD8130 Transient Response vs. Supply, VOUT = 0.2 V p-p VOUT = 1V p-p VS = ±5V VS = ±2.5V VS = ±5V VOUT = 1V p-p CL = 5pF 5.00ns Figure 78.
AD8129/AD8130 CL = 10pF VOUT = 1V p-p G = +2 VOUT = 0.2 V p-p CL = 5pF CL = 2pF VS = ±5V, CL = 10pF 10.00ns 250mV Figure 83. AD8130 Transient Response vs. Load Capacitance, VOUT = 0.2 V p-p 5.00ns 02464-087 50mV 02464-084 VS = ±5V, CL = 2pF Figure 86. AD8130 Transient Response vs. Load Capacitance, VOUT = 1 V p-p, G = +2 VOUT = 2V p-p G = +2 VS = ±5V 2V p-p 1V p-p VS = ±12V 5.00ns Figure 84. AD8130 Transient Response vs. Output Amplitude, VOUT = 0.5 V p-p, 1 V p-p, 2 V p-p 5.
AD8129/AD8130 4V p-p G = +5 VS = ±5V CL = 10pF VIN 2V p-p VOUT 1.00V Figure 89. AD8130 Transient Response with +3 V Common-Mode Input 10.0ns 02464-093 5.00ns 1.00V 02464-090 1V p-p Figure 92. AD8130 Transient Response vs. Output Amplitude VOUT = 8V p-p G = +5 VS = ±5V CL = 10pF VOUT 2.00V Figure 90. AD8130 Transient Response with −3 V Common-Mode Input 2.50V Figure 93. AD8130 Transient Response, VOUT = 8 V p-p, G = +5, VS = ±5 V G = +2 VS = ±12V 5.
AD8129/AD8130 AD8129 TRANSIENT RESPONSE CHARACTERISTICS G = +10, RF = 2 kΩ, RG = 221 Ω, RL = 1 kΩ, CL = 1 pF, VS = ±5 V, TA = 25°C, unless otherwise noted. VS = ±2.5V VS = ±5V VOUT = 1V p-p VS = ±2.5V VOUT = 0.4V p-p 5.00ns 100mV Figure 95. AD8129 Transient Response, VS = ±2.5 V, VOUT = 1 V p-p VS = ±5V 5.00ns 02464-099 250mV 02464-096 VS = ±12V Figure 98. AD8129 Transient Response vs. Supply, VOUT = 0.4 V p-p VOUT = 1V p-p VOUT = 1V p-p CL = 5pF VS = ±5V VS = ±2.5V 5.00ns Figure 96.
AD8129/AD8130 VOUT = 0.4V p-p CL = 5pF VOUT = 1V p-p G = +20 CL = 20pF CL = 10pF 250mV Figure 101 Transient Response vs. Load Capacitance, VOUT = 0.4 V p-p 5.00ns 02464-105 5.00ns 100mV 02464-102 CL = 2pF Figure 104. AD8129 Transient Response, VOUT = 1 V p-p, VS = ±2.5 V to ±12 V VOUT = 2V p-p VO = 2V p-p G = +20 CL = 20pF VO = 1V p-p 500mV Figure 102. Transient Response vs. Output Amplitude, VOUT = 0.5 V p-p, 1 V p-p, 2 V p-p 5.00ns 02464-106 5.00ns 500mV 02464-103 VO = 0.
AD8129/AD8130 VIN 4V p-p G = +50 VS = ±5V CL = 20pF 2V p-p VOUT 5.00ns 1.00V Figure 107. AD8129 Transient Response with +3.5 V Common-Mode Input 12.5ns 02464-111 1.00V 02464-108 1V p-p Figure 110. AD8129 Transient Response vs. Output Amplitude, VOUT = 1 V p-p, 2 V p-p, 4 V p-p VOUT = 8V p-p G = +50 VS = ±5V CL = 20pF G = +20 VS = ±12V CL = 20pF 5.00ns VOUT = 20V p-p 02464-110 2.50V 02464-112 12.5ns Figure 111. AD8129 Transient Response, VOUT = 8 V p-p, G = +50, VS = ±5 V Figure 108.
AD8129/AD8130 G = +1 VS = ±5V RL = 1kΩ 20 17 14 11 –5 02464-117 GAIN NONLINEARITY (0.005%/DIV) G = +1 VS = ±5V 02464-114 SUPPLY CURRENT (mA) 23 –4 –3 –2 –1 0 1 2 DIFFERENTIAL INPUT (V) 3 4 –1.0 5 –0.4 –0.2 0 0.2 0.4 0.6 0.8 G = +1 VS = ±5V RL = 1kΩ 31 25 02464-115 19 –0.6 –0.4 –0.2 0 0.2 0.4 DIFFERENTIAL INPUT (V) 0.6 0.8 02464-118 GAIN NONLINEARITY (0.08%/DIV) G = +1 VS = ±10V –0.8 1.0 Figure 116. AD8130 Gain Nonlinearity, VOUT = 2 V p-p 37 SUPPLY CURRENT (mA) –0.
AD8129/AD8130 15 G = +10 VS = ±5V RL = 1kΩ SUPPLY CURRENT (mA) –0.8 –0.6 –0.4 –0.2 0 0.2 0.4 0.6 0.8 12 11 10 02464-120 –1.0 13 02464-123 GAIN NONLINEARITY (0.005%/DIV) 14 9 1.0 5 0 10 15 20 TOTAL SUPPLY VOLTAGE (V) OUTPUT VOLTAGE (V) 25 30 Figure 122. Quiescent Power Supply Current vs. Total Supply Voltage Figure 119. AD8129 Gain Nonlinearity, VOUT = 2 V p-p 17 G = +10 VS = ±12V RL = 1kΩ GAIN NONLINEARITY (0.
AD8129/AD8130 4.00 4.0 VS = 5V 3.75 AD8130 AD8129 3.5 3.25 OUTPUT VOLTAGE (V) VS = 5V 3.00 2.75 VOUT = 100mV AC AT 1kHz 2.50 2.25 2.00 SOURCING 3.0 +100°C –40°C +25°C 2.0 1.75 SINKING AD8129 1.5 AD8130 02464-126 1.50 1.25 1.00 –50 –35 –20 –5 10 25 40 55 TEMPERATURE (°C) 70 85 02464-129 INPUT COMMON MODE (V) 3.50 VOUT = 100mV AC AT 1kHz 1.0 100 0 Figure 125. Common-Mode Voltage Range vs.
AD8129/AD8130 THEORY OF OPERATION The AD8129/AD8130 use an architecture called active feedback, which differs from that of conventional op amps. The most obvious differentiating feature is the presence of two separate pairs of differential inputs compared with a conventional op amp’s single pair. Typically, for the active feedback architecture, one of these input pairs is driven by a differential input signal, while the other is used for the feedback.
AD8129/AD8130 APPLICATIONS BASIC GAIN CIRCUITS The gain of the AD8129/AD8130 can be set with a pair of feedback resistors. The basic configuration is shown in Figure 132. The gain equation is the same as that of a conventional op amp: G = 1 + RF/RG. For unity-gain applications using the AD8130, RF can be set to 0 (short circuit), and RG can be removed (see Figure 133).
AD8129/AD8130 +V AD8130 VIN 1 100Ω 0.1μF + 3 7 PD +VS It is difficult to calculate the exact component values via strictly mathematical means, because the equations for the cable attenuation are approximate and have functions that are not simply related to the responses of RC networks. The method used in this design was to approximate the required response via graphical means from the frequency response and then select components that would approximate this response.
AD8129/AD8130 +V One way to accomplish this is to drive both REF and RG with the desired offset signal (see Figure 139). Superposition can be used to solve this circuit. First, break the connection between VOFFSET and RG. With RG grounded, the gain from Pin 4 to VOUT is 1 + RF/RG. With Pin 4 grounded, the gain though RG to VOUT is −RF/RG. The sum of these is 1. If VREF is delivered from a low impedance source, this works fine.
AD8129/AD8130 Such a connection, also referred to as a cable-tap amplifier, can be simply made with an AD8130 (see Figure 143). The circuit is configured with unity gain, and if no output offset is desired, the REF pin is grounded. The negative differential input is connected directly to the shield of the cable (or an associated connector) at the point at which it wants to be tapped.
AD8129/AD8130 Another problem can occur with the AD8129 operating at a supply voltage of greater than or equal to ±12 V. The architecture causes the supply current to increase as the input differential voltage increases. If the AD8129 differential inputs are overdriven too far, excessive current can flow into the device and potentially cause permanent damage.
AD8129/AD8130 LAYOUT, GROUNDING, AND BYPASSING The AD8129/AD8130 are very high speed parts that can be sensitive to the PCB environment in which they operate. Realizing their superior specifications requires attention to various details of standard high speed PCB design practice. The first requirement is for a good solid ground plane that covers as much of the board area around the AD8129/AD8130 as possible.
AD8129/AD8130 OUTLINE DIMENSIONS 5.00 (0.1968) 4.80 (0.1890) 8 5 4.00 (0.1574) 3.80 (0.1497) 1 6.20 (0.2440) 4 5.80 (0.2284) 1.27 (0.0500) BSC 0.50 (0.0196) × 45° 0.25 (0.0099) 1.75 (0.0688) 1.35 (0.0532) 0.25 (0.0098) 0.10 (0.0040) 0.51 (0.0201) COPLANARITY SEATING 0.31 (0.0122) 0.10 PLANE 8° 0.25 (0.0098) 0° 1.27 (0.0500) 0.40 (0.0157) 0.17 (0.
AD8129/AD8130 ORDERING GUIDE Model AD8129AR AD8129AR-REEL AD8129AR-REEL7 AD8129ARZ 2 AD8129ARZ-REEL2 AD8129ARZ-REEL72 AD8129ARM AD8129ARM-REEL AD8129ARM-REEL7 AD8129ARMZ2 AD8129ARMZ-REEL2 AD8129ARMZ-REEL72 AD8130AR AD8130AR-REEL AD8130AR-REEL7 AD8130ARZ2 AD8130ARZ-REEL2 AD8130ARZ-REEL72 AD8130ARM AD8130ARM-REEL AD8130ARM-REEL7 AD8130ARMZ2 AD8130ARMZ-REEL2 AD8130ARMZ-REEL72 1 2 Temperature Range 1 −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C