Use Instructions
Table Of Contents
- GLOSSARY & ACRONYMS
- PART 1. GENERAL SYSTEM INFORMATION
- 2. INDICATIONS AND CONTRAINDICATIONS FOR USE
- 3. WARNINGS AND PRECAUTIONS
- CAUTION
- 6. BASELINE MEASUREMENT PREPARATION AND DEVICE SETUP
- 8. THE ALIGNMENT TOOL
- PART 3. AT-HOME CPM SYSTEM USE
- PART 4. LIGHTS, SOUNDS, AND TROUBLESHOOTING
- 12. CPM DEVICE LIGHTS AND SOUNDS
- 13. BASE STATION INDICATIONS
- 14. BUTTON PRESSES
- 15. GENERAL TROUBLESHOOTING / FAQS
- 15.1 Physician Q&As
- Q: No data from my patient is appearing on the server, but after getting in touch with the patient, they say that they have been taking measurements consistently with no issue and their device is connected to a plugged- in Base Station.
- Q: No size of the CPM Device fits my patient.
- Q: I initiated a patient mode measurement while trying to put the device into Bluetooth pairing mode and now I can’t pair the CPM Device to the Mobile App.
- Q: How do patients get more adhesives when they run out?
- Q: Can the CPM System be used near other electronic or medical equipment such as telephones, televisions, computers, etc.?
- Q: Is data secure when transmitting from the CPM Device to the Mobile App, the Device to the Base Station, or the Base Station to the Cloud platform?
- 15.2 Patient Q&As
- Q: The CPM Device is not lighting up when plugged into the Base Station to charge.
- Q: Nothing happens when I am trying to start a measurement and/or the button is pressed on the CPM Device.
- Q: The device visually does not stick well to my body or is obviously peeling up.
- Q: I lost the clear protective liners for covering the adhesive.
- Q: I pressed the button accidentally/too early and a measurement started before the device was on my body. How do I get the device to stop beeping?
- Q: The CPM Device continues to beep, indicating there are errors, during a measurement.
- Q: Can I shower with the CPM Device or get it wet?
- Q: Can I travel with the CPM System?
- Q: A piece or part broke off the device, base station, or alignment tool.
- Q: What do I do if I think I am having a medical emergency or decompensation event?
- 15.1 Physician Q&As
- PART 5. CLEANING AND MAINTENANCE
- PART 6. SYSTEM SPECIFICATIONS
- PART 7. SYMBOLS GLOSSARY
34
Version C
Clinician Instructions for Use – Device and Mobile Application
C
PART 3. AT-HOME CPM SYSTEM USE
This section of the Clinician Instructions for use is intended to help you train your patient on how to use their CPM
System at home.
9.
HOME SETUP
1)
Place the CPM Base Station on a
sturdy table
near where the patient sleeps.
2)
Attach the power adapter to the CPM Base Station (the adaptor is on the bottom right of the Base Station).
3)
Plug in the Base Station’s power adapter to an electrical outlet nearby.
4)
Open the Base Station, ensuring that the CPM Device is seated inside with the magnetic charger connected.
The Base Station power LED as well as the device charge LED should be illuminated.
5)
Five (5) adhesives at a time can be stored (in their packaging) until ready to use in the Base Station
compartment behind the mirror. Note that the initial CPM patient kit includes five (5) adhesives in the
Base Station adhesive storage compartment, while adhesive refill packaging contains fifteen (15)
adhesives at a time. Always keep adhesives that do not fit inside the Base Station in a safe and dry
location.
Figure 22 a-c. a-b) Plugging the Base Station into the wall and c) Magnetic charging and LED indications in the Base Station.
IMPORTANT
The CPM Device and Base Station should be located near your patient’s place of sleep, on a sturdy
table, with the Base Station plugged in and the lid closed when not in use. Placing the Base Station
near a window is ideal for achieving consistent and strong cellular signal.
CAUTION
Ensure that the Base Station is in a stable position and is not at risk of falling.