Use Instructions
Table Of Contents
- GLOSSARY & ACRONYMS
- PART 1. GENERAL SYSTEM INFORMATION
- 2. INDICATIONS AND CONTRAINDICATIONS FOR USE
- 3. WARNINGS AND PRECAUTIONS
- CAUTION
- 6. BASELINE MEASUREMENT PREPARATION AND DEVICE SETUP
- 8. THE ALIGNMENT TOOL
- PART 3. AT-HOME CPM SYSTEM USE
- PART 4. LIGHTS, SOUNDS, AND TROUBLESHOOTING
- 12. CPM DEVICE LIGHTS AND SOUNDS
- 13. BASE STATION INDICATIONS
- 14. BUTTON PRESSES
- 15. GENERAL TROUBLESHOOTING / FAQS
- 15.1 Physician Q&As
- Q: No data from my patient is appearing on the server, but after getting in touch with the patient, they say that they have been taking measurements consistently with no issue and their device is connected to a plugged- in Base Station.
- Q: No size of the CPM Device fits my patient.
- Q: I initiated a patient mode measurement while trying to put the device into Bluetooth pairing mode and now I can’t pair the CPM Device to the Mobile App.
- Q: How do patients get more adhesives when they run out?
- Q: Can the CPM System be used near other electronic or medical equipment such as telephones, televisions, computers, etc.?
- Q: Is data secure when transmitting from the CPM Device to the Mobile App, the Device to the Base Station, or the Base Station to the Cloud platform?
- 15.2 Patient Q&As
- Q: The CPM Device is not lighting up when plugged into the Base Station to charge.
- Q: Nothing happens when I am trying to start a measurement and/or the button is pressed on the CPM Device.
- Q: The device visually does not stick well to my body or is obviously peeling up.
- Q: I lost the clear protective liners for covering the adhesive.
- Q: I pressed the button accidentally/too early and a measurement started before the device was on my body. How do I get the device to stop beeping?
- Q: The CPM Device continues to beep, indicating there are errors, during a measurement.
- Q: Can I shower with the CPM Device or get it wet?
- Q: Can I travel with the CPM System?
- Q: A piece or part broke off the device, base station, or alignment tool.
- Q: What do I do if I think I am having a medical emergency or decompensation event?
- 15.1 Physician Q&As
- PART 5. CLEANING AND MAINTENANCE
- PART 6. SYSTEM SPECIFICATIONS
- PART 7. SYMBOLS GLOSSARY
40
Version C
Clinician Instructions for Use – Device and Mobile Application
C
12.2 Battery and Charging
When the CPM Device is plugged into the Base Station to charge, the LED bar will “breathe” green.
To get a sense of the charge of the device when it is NOT plugged into the Base Station, tap the blue button on the
device and it will blink green, yellow, or red depending on device charge as shown below. The light will blink twice and
then stay on for 5 seconds to indicate the charge.
Description
Actively Charging
Only when docked,
LED “breathes”
Good battery level
(>75%)
Only when woken up
Ok battery level
(10% - 75%)
Only when woken up
Low Battery Level
(<10%)
Only when woken up
Actions
Device is ready to take
a measurement when
unplugged from the
Base Station.
Device is ready to
take a
measurement.
Device is ready to
take a
measurement.
Dock to the Base Station
until the light is yellow or
green. The battery is too
low to take a
measurement.
Description
Plug the device in
Only after a reading has been attempted and/or completed.
The LED color will vary depending on the battery charge of
the device (good = green, ok = yellow, red = low). If the light
flashes red, the battery is too low to take a measurement.
Sounds
Three notes, once every minute for 5 minutes
Actions
Return the device to the Base Station.