Datasheet
Table Of Contents
- Summary
- Dedicated Audio Components
- Table of Contents
- Revision History
- General Description
- SHARC Family Core Architecture
- SIMD Computational Engine
- Independent, Parallel Computation Units
- Data Register File
- Context Switch
- Universal Registers
- Timer
- Single-Cycle Fetch of Instruction and Four Operands
- Instruction Cache
- Data Address Generators with Zero-Overhead Hardware Circular Buffer Support
- Flexible Instruction Set
- On-Chip Memory
- On-Chip Memory Bandwidth
- ROM-Based Security
- Family Peripheral Architecture
- I/O Processor Features
- System Design
- Development Tools
- Additional Information
- Related Signal Chains
- SHARC Family Core Architecture
- Pin Function Descriptions
- Specifications
- Operating Conditions
- Electrical Characteristics
- Package Information
- ESD Caution
- Maximum Power Dissipation
- Absolute Maximum Ratings
- Timing Specifications
- Core Clock Requirements
- Power-Up Sequencing
- Clock Input
- Clock Signals
- Reset
- Interrupts
- Core Timer
- Timer PWM_OUT Cycle Timing
- Timer WDTH_CAP Timing
- DAI Pin to Pin Direct Routing
- Precision Clock Generator (Direct Pin Routing)
- Flags
- Memory Read—Parallel Port
- Memory Write—Parallel Port
- Serial Ports
- Input Data Port (IDP)
- Parallel Data Acquisition Port (PDAP)
- Pulse-Width Modulation Generators
- Sample Rate Converter—Serial Input Port
- Sample Rate Converter—Serial Output Port
- S/PDIF Transmitter
- S/PDIF Receiver
- SPI Interface—Master
- SPI Interface—Slave
- JTAG Test Access Port and Emulation
- Output Drive Currents
- Test Conditions
- Capacitive Loading
- Thermal Characteristics
- 144-Lead LQFP_EP Pin Configurations
- 136-Ball BGA Pin Configurations
- Package Dimensions
- Automotive Products
- Ordering Guide
Rev. J | Page 40 of 60 | July 2013
ADSP-21362/ADSP-21363/ADSP-21364/ADSP-21365/ADSP-21366
S/PDIF Transmitter Input Data Timing
The timing requirements for the S/PDIF transmitter are given
in Table 36. Input signals are routed to the DAI_P20–1 pins
using the SRU. Therefore, the timing specifications provided
below are valid at the DAI_P20–1 pins.
Oversampling Clock (TxCLK) Switching Characteristics
The S/PDIF transmitter requires an oversampling clock input.
This high frequency clock (TxCLK) input is divided down to
generate the internal biphase clock.
Table 36. S/PDIF Transmitter Input Data Timing
K Grade Y Grade
Parameter Min Max Min Max Unit
Timing Requirements
t
SISFS
1
Frame Sync Setup Before Serial Clock Rising Edge 3 3 ns
t
SIHFS
1
Frame Sync Hold After Serial Clock Rising Edge 3 3 ns
t
SISD
1
Data Setup Before Serial Clock Rising Edge 3 3 ns
t
SIHD
1
Data Hold After Serial Clock Rising Edge 3 3 ns
t
SITXCLKW
Transmit Clock Width 9 9.5 ns
t
SITXCLK
Transmit Clock Period 20 20 ns
t
SISCLKW
Clock Width 36 36 ns
t
SISCLK
Clock Period 80 80 ns
1
The serial clock, data and frame sync signals can come from any of the DAI pins.The serial clock and frame sync signals can also come via PCG or SPORTs. PCG’s input can
be either CLKIN or any of the DAI pins.
Figure 32. S/PDIF Transmitter Input Timing
SAMPLE EDGE
DAI_P20–1
(TxCLK)
DAI_P20–1
(SCLK)
DAI_P20–1
(FS)
DAI_P20–1
(SDATA)
t
SITXCLKW
t
SITXCLK
t
SISCLKW
t
SISCLK
t
SISFS
t
SIHFS
t
SISD
t
SIHD
Table 37. Oversampling Clock (TxCLK) Switching Characteristics
Parameter Max Unit
Frequency for TxCLK = 384 × Frame Sync Oversampling Ratio × Frame Sync <= 1/t
SITXCLK
MHz
Frequency for TxCLK = 256 × Frame Sync 49.2 MHz
Frame Rate (FS) 192.0 kHz