Datasheet

ADuM2400/ADuM2401/ADuM2402 Data Sheet
Rev. F | Page 12 of 24
ABSOLUTE MAXIMUM RATINGS
Table 9.
Parameter Rating
Storage Temperature Range (T
ST
) −65°C to +150°C
Ambient Operating Temperature
Range (T
A
)
−40°C to +105°C
Supply Voltage Range (V
DD1
, V
DD2
)
1
−0.5 V to +7.0 V
Input Voltage Range
(V
IA
, V
IB
, V
IC
, V
ID
, V
E1
, V
E2
)
1, 2
−0.5 V to V
DDI
+ 0.5 V
Output Voltage Range
(V
OA
, V
OB
, V
OC
, V
OD
)
1, 2
−0.5 V to V
DDO
+ 0.5 V
Average Output Current Per Pin
3
Side 1 (I
O1
) −18 mA to +18 mA
Side 2 (I
O2
) −22 mA to +22 mA
Common-Mode Transients
4
−100 kV/µs to +100 kV/µs
1
All voltages are relative to their respective ground.
2
V
DDI
and V
DDO
refer to the supply voltages on the input and output sides of a
given channel, respectively. See the PC Board Layout section.
3
See Figure 4 for maximum rated current values for various temperatures.
4
Refers to common-mode transients across the insulation barrier. Common-
mode transients exceeding the Absolute Maximum Rating can cause latch-
up or permanent damage.
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
ESD CAUTION
Table 10. Maximum Continuous Working Voltage
1
Parameter Max Unit Constraint
AC Voltage, Bipolar Waveform 565 V peak 50-year minimum lifetime
AC Voltage, Unipolar Waveform
Reinforced Insulation 846 V peak Maximum approved working voltage per IEC 60950-1 and VDE V 0884-10
DC Voltage
Reinforced Insulation 846 V peak Maximum approved working voltage per IEC 60950-1 and VDE V 0884-10
1
Refers to continuous voltage magnitude imposed across the isolation barrier. See the Insulation Lifetime section for more details.
Ta
ble 11. Truth Table (Positive Logic)
V
Ix
Input
1
V
Ex
Input
V
DDI
State
1
V
DDO
State
1
V
Ox
Output
1
Notes
H H or NC Powered Powered H
L
H or NC
Powered
Powered
L
X L Powered Powered Z
X H or NC Unpowered Powered H Outputs return to input state within 1 µs of V
DDI
power restoration.
X L Unpowered Powered Z
X X Powered Unpowered Indeterminate Outputs return to input state within 1 µs of V
DDO
power restoration if
V
Ex
state is H or NC. Outputs return to high impedance state within
8 ns of V
DDO
power restoration if V
Ex
state is L.
1
V
Ix
and V
Ox
refer to the input and output signals of a given channel (A, B, C, or D). V
Ex
refers to the output enable signal on the same side as the V
Ox
outputs. V
DDI
and
V
DDO
refer to the supply voltages on the input and output sides of the given channel, respectively.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.