Assembly Instructions Century Frame Tent 20’ and 30’ Hex SALES OFFICES: 1100 BURCH DRIVE PO BOX 3477 EVANSVILLE, IN 47733 USA EC 2616 PHONE: 812-867-2421 FAX: 812-867-0547 1-800-544-4445 EMAIL: tents@anchorinc.com www.anchorinc.
Parts Lists & Illustrations 20’ Hex Parts Table Quantity Description 30’ Hex Parts Table Quantity Description 1 Center Pole 1 Center Pole 3 Cables 3 Cables 6 Tension Straps 6 Tension Straps 6 10’ Eaves 6 15’ Eaves 6 Uprights 6 Uprights 6 Base Plates 6 Base Plates 6 Guy Webs 6 Guy Webs 1 Bag with Top 1 Bag with Top 6 Corner Weldments 6 Corner Weldments 6 Walls (10’ - 2 pc. -- optional) 6 Walls (15’ - 2 pc.
Caution! Inspect Site Consult local Utility Company prior to installation. Prior to assembly be sure to look around area for obstacles, pipes, wires, etc. Corner Weldment 10’ Eave 15’ Eave y tel pro 15’ xim a Ap Ap pro 30’ xim ate Ap pro 20’ xim ate ly Ap pro 10’ xim ate ly ly Corner Weldment Cable Cable Ap pro 25’ xim a Ap pro 17’ xim ate tel y ly 20’ Hexagon Lay Out 30’ Hexagon Lay Out Step 1 Lay out parts for assembly as shown in the diagrams above.
Step 3 Attach Cables Attach one eye end of cable to weldment hook on a corner weldment. At the opposite corner, raise frame until cable loop slips onto weldment hook, then lower to ground. Repeat until all 3 cables are attached to frame. Weldment hook. Cable Cable eye end. Figure 3 Step 4 Put Top on Frame Unfold top over eaves and cables. Pull tabs at corners of top over corner weldments. Secure by placing slot in tabs over ring on corner weldment.
Step 5 (cont’d) For 30’ hex frame: Two frame lifts are required. Position the two lifts on one eave as shown and attach hooks to eave tube. Crank both lifts at the same time. Stop when uprights will fit onto weldments. Lower and remove frame lifts. 30’ Hex Frame Wind Upright Note: If wind is strong, drive in stakes through the guy web ring and tie off loosely before lifting frame.
Pole Pin Center Pole Center Pole Cables Lock Pin Roller Figure 7b Figure 7c Step 8 Lift Other Side Raise opposite side by repeating Step 5. Attach remaining uprights. Plumb uprights. Step 9 Installing Optional Walls Determine proper mating of 2-piece walls with labels on the inside. Slide tabs at top of walls into bottom outside channel opening (see Century Frame extrusion drawing on Page 3). Orient walls so that beading edges are adjacent to uprights and the lace edges meet in the middle.
Step 11 Secure Tent Make certain that tent is positioned in the desired location. Drive a 1” x 30” stake through each base plate. Drive a 1” x 30” stake through the ring at bottom of web guy. See Figure 9 for positioning of stake. Tension web guy. Proceed around tent until all web guys are tensioned. See guy web operating instructions provided. IMPORTANT NOTE: PLEASE REFER TO CAUTION AND OTHER ANCHORING INFORMATION ON BACK PAGE.
EVANSVILLE, INDIANA PHONE NUMBER 812· 867· 2421 FAX NUMBER 812· 867· 0547 Anchor products are of superior design and operate best within the parameters of these instructions. It is imperative that the instructions be carefully read and COMPLETELY FOLLOWED. Please read installation instructions before the installation or removal of this product. Installation instructions are available online at www.anchorinc.com or by calling 1-800-544-4445. CAUTION: 1.