® Range Hood Pro Pyramid Hidden Controls 30” and 36” User Manual & Installation Instructions IMPORTANT SAFETY INSTRUCTIONS Carefully read the important information regarding installation, safety and maintenance. Keep these instructions for future reference.
Before You Begin INSTALLERS - Start Here Safety Instructions are on pages 4 and 5 and Installation Instructions are on pages 6 to 16. Please perform these steps: 1. Read the safety instructions. 2. Read all instructions in the Installation section of this manual BEFORE installing the range hood. 3. Remove all packing materials. 4. When finished, make sure to leave these instructions with the consumer. 5. Installation is to be done by a qualified technician only.
Table of Contents Before You Begin................................................................................................................................ 2 Table of Contents............................................................................................................................... 3 Important Safety Information............................................................................................................. 4 Included Parts..............................................
Important Safety Information READ ALL INSTRUCTIONS BEFORE USE Read and follow all instructions before using the range hood to prevent the risk of fire, electric shock, personal injury, or damage when using the range hood or appliances with the range hood. This guide does not cover all possible conditions that may occur. Always contact your service technician or manufacturer about problems that you do not understand.
Important Safety Information WARNING: TO REDUCE RISK OF A RANGE TOP GREASE FIRE: To reduce the risk of injury to persons in the event of a gas leaks: a) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings. • Extinguish any open flame. • DO NOT turn on the lights or any type of appliance. • Open all doors and windows to disperse the gas.
Included Parts Main Housing Damper 12 x Main Housing Screws 4 x Damper Screws 2 x Upper Chimney Screws Baffle Filters x 2 Motor Body Grease Trays x 2 Lower Chimney Upper Chimney Upper Chimney Bracket Hardware Note: For safety reasons, range hood mounting screws and anchors will not be included due to the variation of cabinetry constructions and wall material. Please consult your installation specialist regarding the optimal type of mounting screws and wall anchors to suit your home’s construction.
Range Hood Dimensions 15-5/8” (397 mm) 9-5/8” (245 mm) 19” to 37-3/4” (483 mm to 958 mm) 13-9/16” (345 mm) 3-1/2” (90 mm) 20-1/4” (515 mm) 29-7/8” / 35-3/8” (760 mm / 900 mm) Specification Body Design Power Rating Stainless Steel 120 V / 60 Hz (cETLus Certified) Total Input Power 406 W Motor Input Power 400 W Amperage 3.
Installation STEP 1 Read the Safety Instructions • It is very important to read the safety instructions on pages 4 and 5. IMPORTANT: It is the installer’s responsibility to comply with installation clearances. STEP 2 Unpack Range Hood and Prepare Tools • Carefully unpack the range hood and parts. Make sure all parts are included as shown on page 6. • DO NOT remove the protective film covering the appliance until the installation is fully completed.
Installation STEP 5 Venting Installation Guidelines • The following steps are for exterior ventilation. IMPORTANT: • Vent system must terminate to the outside (roof or side wall). • DO NOT terminate the vent system in an attic or other enclosed area. • DO NOT use 4” (10.2 cm) laundry-type wall caps. • Use metal/aluminum vent only. A rigid metal/aluminum vent is recommended. • DO NOT use a plastic vent. • Always keep the duct clean to ensure proper airflow.
Installation STEP 6 Prepare Motor Body • Place the motor body on the edge of a flat surface, such as the corner of a table. • To protect the flat surface from scratches, place the first square piece of styrofoam that you see when the motor body box is opened, on the flat surface. Foam Table STEP 7 Insert Motor Body into Main Housing • Place the main housing over the motor body as shown below. • Ensure the motor door and black controls on front panel of range hood are facing upwards.
Installation STEP 8 Attach Motor Body to Main Housing • Align the 3 screw holes on the bottom edge of the Motor Body with the 3 holes on the bottom edge of the Main Housing. • Then align the remaining 9 screw holes and screw together the two pieces using the screws provided. STEP 9 Join the Connectors • Join together the quick connectors at the back of the main housing and motor body.
STEP 11 Mount Range Hood Onto Wall • Position the range hood’s mounting key holes securely onto the range hood mounting screws. • Finish screwing in the screws until they cannot tighten any further. STEP 12 Install Damper • Place the damper gasket followed by the damper over the ventilation hole on top of the motor body. • Secure using the four screws (included). STEP 13 Connect Ductwork • Attach ductwork to damper. Secure the ductwork with duct tape to make sure joints are secure and air-tight.
Installation IMPORTANT: • Observe all governing codes and ordinances. • It is the customer’s responsibility to contact a qualified electrical installer. • If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate. A 120-Volt, 60 Hz, AC-only, fused electrical supply is required on a separate 15-amp circuit, fused on both sides of the line. • DO NOT ground to a gas pipe.
Installation STEP 16 Install Upper Chimney Bracket STEP 17 Install Upper Chimney • Position the upper chimney bracket onto the wall directly below the ceiling. Align the upper chimney bracket with the range hood below. • Remove the protective film from the upper chimney. Carefully slide the upper chimney inside the lower chimney. • Use a pencil to mark desired placement of the upper chimney bracket on the wall.
Installation STEP 18 Install Grease Trays • Place the grease trays into the the track at the back of the range hood. • Slide them left and right until all trays are placed side-by-side in the track. • The baffle filters and grease trays should be cleaned once a month, or as needed. See page 18 for cleaning instructions. STEP 19 Install Baffle Filter • Hold the baffle filter by the two knobs. • Place the front of the baffle against the interior front of the range hood.
Operation Using the Fan u v Press the 1 button to turn on the fan and set it to slow speed; the button will light up. Press the same button to turn the fan off. Press the 2 button to increase the speed to the second setting; the 2 button will light up. Turning the Light On of Off 1 2 3 T u Press the button to turn the light on. 1 2 3 T v Press the button again to turn the light off. 2 3 T Press the 3 button again to increase the speed to the third setting; the 3 button will light up.
Maintenance Replacing the Light Bulbs u Unplug the unit from the AC outlet. v Remove five screws from the light panel, then remove the light bulbs by popping them out. Cleaning the Range Hood Be sure electrical power is off and all surfaces are cool before cleaning or servicing any part of the hood. Range Hood Body • Do not use a steel wool pad; it will scratch the surface. • To clean the stainless steel surface, use warm soapy water or a stainless steel cleaner.
Replacement Parts 1 2 3 5 4 7 6 9 8 16 10A & 10B Description Part Code Description Part Code 1 - Capacitor PACAP-15 10B - Grease Tray 36” PAGTR-02 2 - Circuit Board PABRD-14 11 - Light Panel 30”* PALPL-20 3 - Control Panel PACPL-17 12 - Light Panel 36”* PALPL-21 4 - Transformer PATRA-13 13 - Hardware Bag* PASCR-16 5 - Damper & Gasket PADAM-17 14 - Baffle Filter 30”* PA02047 PALIT-14 15 - Baffle Filter 36”* PA02048 PAUCB-15 6 - Light Bulb 7 - Motor PAMOT-36 16 - Upper
Please register your product warranty by visiting the Ancona Home website. Canada & USA Phone: 888-686-0778 Fax: 800-350-8563 Email: service@anconahome.com Website: www.anconahome.com Ancona is in association with Mr Appliance for all after sales service calls. Please contact their service provider or visit their website: Phone: 888-998-2011 Website: www.mrappliance.com MAAN-1139-03 © 2017 Copyright of Ancona Home. All rights reserved.