® Range Hood Ancona Elite WPE630 & WPE636 User Manual & Installation Instructions IMPORTANT SAFETY INSTRUCTIONS Carefully read the important information regarding installation, safety and maintenance. Keep these instructions for future reference.
Before You Begin INSTALLERS - Start Here Safety Instructions are on pages 4 and 5 and Installation Instructions are on pages 6 to 13. Please perform these steps: 1. Read the safety instructions. 2. Read all instructions in the Installation section of this manual BEFORE installing the range hood. 3. Remove all packing materials. 4. When finished, make sure to leave these instructions with the consumer. 5. Installation is to be done by a qualified technician only.
Table of Contents Before You Begin................................................................................................................................ 2 Table of Contents............................................................................................................................... 3 Important Safety Information............................................................................................................. 4 Included Parts..............................................
Important Safety Information READ ALL INSTRUCTIONS BEFORE USE Read and follow all instructions before using the range hood to prevent the risk of fire, electric shock, personal injury, or damage when using the range hood or appliances with the range hood. This guide does not cover all possible conditions that may occur. Always contact your service technician or manufacturer about problems that you do not understand.
Important Safety Information WARNING: TO REDUCE RISK OF A RANGE TOP GREASE FIRE: To reduce the risk of injury to persons in the event of a gas leaks: a) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings. • Extinguish any open flame. • DO NOT turn on the lights or any type of appliance. • Open all doors and windows to disperse the gas.
Included Parts Range Hood Damper Damper Screws (4 + 1 pcs) Filters 30 in. (2 pcs) Filters 36 in. (3 pcs) Rubber pads (12 pcs) Upper Chimney Screws (2 + 1 pcs) (already installed) Lower Chimney Screws (8 pcs + 1) Lower Chimney Upper Chimney Upper Chimney Bracket Hardware Note: For safety reasons, range hood mounting screws and anchors will not be included due to the variation of cabinetry constructions and wall material.
Range Hood Dimensions 0 mm) 6.3” (16 ) 60 mm 10.2 “ (2 18.9 “ - 37.5” (480 mm - 954 mm) 17.1“ (435 mm) 10 (25 .2 “ 9m m) ) 91.5 mm 11.5 “ (2 4.7 “ (120 mm) 1.18 “ (30 mm) 18. 9“ (48 m) ) 00 mm 0m .4 “ (9 ) / 35 60 mm 10.5” (266.5 mm) 29.9 “ (7 Specifications Body Design Power Rating Stainless Steel 120 V / 60 Hz (cETLus Certified) Total Input Power 466 W Motor Input Power 460 W Total Amps 3.
Installation STEP 1 Read the Safety Instructions • It is very important to read the safety instructions on pages 4 and 5. IMPORTANT: It is the installer’s responsibility to comply with installation clearances. STEP 2 Unpack Range Hood and Prepare Tools • Carefully unpack the range hood and parts. Make sure all parts are included as shown on page 6. • DO NOT remove the protective film covering the appliance until the installation is fully completed.
Installation STEP 5 Venting Installation Guidelines • The following steps are for exterior ventilation. • If you require a ductless installation, please visit anconahome.com to purchase a recirculation kit. IMPORTANT: • Vent system must terminate to the outside (roof or side wall). • DO NOT terminate the vent system in an attic or other enclosed area. • DO NOT use 4 in. (10.2 cm) laundry-type wall caps. • Use metal/aluminum vent only. A rigid metal/aluminum vent is recommended.
Installation STEP 6 Mark Placement of Range Hood Mounting Screws • Use a pencil to mark on the wall the desired placement of the range hood mounting screws. • Screw two wood screws (not provided) into wall. • Leave approximately 1/4 in. (6.3 mm) of the screw head protruding from the wall to allow clearance for mounting the range hood. • Use threaded drywall anchors when mounting the range hood onto sheet rock. Mounting the hood into wall studs or lumbars is highly recommended.
STEP 9 Connect Ductwork • Attach ductwork to damper. Secure the ductwork with duct tape to make sure joints are secure and air-tight. • Do not install the duct tape too tightly as this may prevent the damper flaps from opening which will overwork the motor and cause improper functioning of the unit. • Fasten all connections with sheet metal screws and tape all joints with certified aluminum or foil tape. Use caulking to seal exterior wall or roof opening around the cap.
Installation STEP 11 Install Lower Chimney • Place lower chimney on top of the main housing. STEP 12 Install Upper Chimney Bracket • Position the upper chimney bracket onto the wall directly below the ceiling. Align the upper chimney bracket with the range hood below. • Use a pencil to mark desired placement of the upper chimney bracket on the wall. • Use two wood screws (not provided), and screw the upper chimney bracket into the wall.
Installation STEP 13 Install Upper Chimney STEP 14 Install Filters • Remove the protective film from the upper chimney. Carefully slide the upper chimney inside the lower chimney. • Place two rubber pads on opposite side of each filter handle. • Extend the telescopic upper chimney until it reaches the upper chimney bracket and attach the upper chimney to the bracket using the provided screws. • Peel off protective film from the rest of the range hood. • Hold the baffle filter by the knob.
Operation Using the Fan u Press to begin low speed. Screen will display 1. Press to increase speed suction. Screen will display increments as 2, 3, 4. Turning the Light On of Off u Press to turn light on and again to turn light off. v Press while light is on to have light turn off after “15 minutes”. Press again to stop suction. Screen will display 00. v Press to begin high speed suction. Screen will display 3. Press again to begin high speed suction to 4. Press again to stop suction.
Maintenance Replacing the Light Bulbs u Unplug the unit from the AC outlet. v Remove five screws from the light panel, then remove the light bulbs by popping them out. Cleaning the Range Hood Be sure electrical power is off and all surfaces are cool before cleaning or servicing any part of the hood. Range Hood Body • Do not use a steel wool pad; it will scratch the surface. • To clean the stainless steel surface, use warm soapy water or a stainless steel cleaner.
Please register your product warranty by visiting the Ancona Home website. Canada & USA Phone: 1-888-686-0778 Fax: 800-350-8563 Email: service@anconahome.com Website: www.anconahome.com Ancona is in association with Mr Appliance for all after sales service calls. Please contact their service provider or visit their website: Phone: 1-888-998-2011 Website: www.mrappliance.com MAAN1162-04 © 2017 Copyright of Ancona Home. All rights reserved.
