MODEL: GCP430 & GCP436 IMPORTANT SAFETY INSTRUCTIONS Carefully read the following important information regarding installation safety and maintenance. Keep these instructions for future reference.
IMPORTANT SAFETY NOTICE READ AND SAVE THESE INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE INSTALLING AND OPERATING THIS APPLIANCE ● ● ● ● The installation in this manual is intended for qualified installers, service technicians or persons with similar qualified background. Installation and electrical wiring must be done by qualified professionals and in accordance with all applicable codes and standards, including fire-rated construction.
IMPORTANT SAFETY NOTICE READ AND SAVE THESE INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE INSTALLING AND OPERATING THIS APPLIANCE WARNING: TO REDUCE RISK OF A RANGE TOP GREASE FIRE: a) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings. b) Always trun hood ON when cooking at high heat or when flambeing food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé).
PARTS SUPPLIED: 1 FILTER Hardware Note: For safety reasons, range hood mounting screws and anchors will not be included due to the variation of cabinetry constructions and wall material. Please consult your installation specialist regarding the optimal type of mounting screws and wall anchors to suit your home’s construction.
VENTING REQUIREMENTS: • • • • • • • HEIGHT & CLEARANCE: Vent system must terminate to the outside (Roof or side wall). DO NOT terminate the vent system in an attic or other enclosed area. DO NOT use 4” (10.2 cm) laundry-type wall caps. Use metal/aluminum vent only. Rigid metal/ aluminum vent is recommended. DO NOT use plastic vent. Always keep the duct clean to ensure proper airflow. Calculate the following figures before installation: 1. Distance from the floor to the ceiling 2.
IMPORTANT: • • • • • • • • A minimum of 6” round or 3-1/4 x 10” rectangular duct (purchased separately) must be used to maintain maximum airflow efficiency. Always use rigid type metal/aluminum ducts if available to maximize airflow when connecting to provided duct. Please use Duct Run Calculation below to compute total available duct run when using elbows, transitions and caps. ALWAYS, when possible, reduce the number or transitions and turns.
VENTING METHODS: • This range hood is factory set for venting through the roof or wall. • Vent work can terminate either through the roof or wall. To vent through a wall, a 90° elbow is needed. IMPORTANT: • NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside.
ELECTRICAL REQUIREMENTS: IMPORTANT: Observe all governing codes and ordinances. It is the customer’s responsibility to contact a qualified electrical installer. If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate. A 120-Volt, 60 Hz, AC-only, fused electrical supply is required on a separate 15-amp circuit, fused on both sides of the line. DO NOT ground to a gas pipe.
PREPARATIONS: Advanced Preparations: • Be familiar with the controls of the range hood by reading through Range Hood Operations, Page 13. • Place the range hood on a flat, stable surface. Connect the range hood to a designated standard outlet (120-Volt, 60Hz, AC only) and turn on the range hood. Verify all operations of the range hood by referring to Range Hood Operations.
INSTALLATION: INSTALLATION: Installations fer to4Page 4 for parts): Installations (refer to(rePage for parts): NOTE: Use thr eaded drywall anchors only when NOTE: Use threaded drywall anchors only when mounting the hood on sheet rock. Mounting mounting the hood on sheet rock. Mounting the hood on wall studs or lumbars is highly the hood on wall studs or lumbars is highly recommended. recommended. Step 1: Measuring • Measure the distance between stove top and the bot to m of range hood.
INSTALLATION CONTINUE: Step 5: Installing the damper • Fix the damper on the top vent of hood with 4 screws (requires screw E). • If ventilation system is equipped with an external air duct with a different diameter, apply a reduction fitting. • However, for maximum performance and safety, a 6” round ducting is recommended. (See Figure # 3) 3 Step 6: Mounting the hood on the wall • Hang the range hood on the hooks of the lower mounting bracket. (See Figure # 4) • Screw the range hood to the wall .
INSTALLATION CONTINUE: Step 7: Installing the decorative chimney and inner chimney bracket • Remove the protective coating from the inner chimney. Carefully slide the inner chimney down into the outer chimney. • Use 2 screws (requires screw F) to fix the two chimneys together with the lower chimney bracket, make sure inside chimney is moving freely. (See Figure # 6) • Install the chimneys on the hood.
CONTROL PANEL OPERATION: Control Panel Layout and Buttons Configurations: Lights: Press the light button Power Settings: Press the to turn halogen lights on and off. once the motor starts to operate at low speed. Press the again and the motor will reach medium speed. once Press the again and the motor will reach high speed.
6 2/5"(163mm) 11 7/8"(302mm) 11 1/4"(286mm) 11 3/4"(298mm) 9 1/16"(231mm) 4 1/2"(115mm) 4 1/2"(115mm) 3 1/8"(82mm) 1 5/8" (40mm) 3 1/8"(82mm) 1 1/8" (28mm) 5/8"(16mm) 9 15/16"(253mm) 14
MEASUREMENTS AND DIAGRAMS: Height of range hood: 22.4” - 41.8” (569mm -1061mm). This range hood can reach a 9' ceiling if installed at 30.5" from the cooking surface. 12” (305 mm) 19.6" to 39" (500 mm to 992 mm) 10.8" (275 mm) 2.72” (69 mm) 19.6” (500 mm) Glass Depth 15.71” (399 mm) 29.52” (750 mm) 10.8”(275 mm) 15” (380 mm) 19.
TROUBLE SHOOTING: 1) If the range hood or halogen light does not operate after installation: • Check if the range hood has been plugged in, make sure that all power has been turned back ON,fused not blown and all electrical wiring are properly connected. 2) The range hood vibrates when the blower is on: • The range hood might not have been secured properly on to the ceiling or wall. 3) The blower or fan seems weak: • Check that the duct sized used is at least 6” or 3-1/4 x 10”.
RANGE HOOD ASSEMBLY: 1 Aluminum filter 2 LED light puck 3 Switch panel 4 Rubber strip 5 Switch box 6 Electronic switch 7 Switch box cover 8 Switch bracket 9 Blower 10 Propeller 11 Motor 12 Inlet grid 13 Housing set 14 Hook 15 Outlet 16 Power cord 17 PCB box base 18 PCB 19 PCB box cover 20 Glass 21 Outer chimney 22 Outer chimney bracket 23 Inner chimney 24 Inner chimney bracket 17
SPECIFICATIONS: Body design Stainless steel Power Rating 120V / 60Hz (USA & Canada standard) cETLus Certified Total input power 235.1W Motor Input Power 230W Total Ampere 1.96A Levels of speed control 3 levels Interference Protection Radio frequency interference protected Air Flow 400 CFM Noise Level Low speed 52 dBA Number of Motor Single motor Fan Type Single chamber quiet Control Type Electronic control Filtration Type 1 x Aluminum filter Illumination 2 x 2.
BLOWER ASSEMBLY: No. 1 2 3 4 Description No. Description 5 Incabloc Rubber 6 Aluminum Cover 7 Plastic Wind Net 8 Sealing Gasket Blower Wind Wheel Nut Wind Wheel Motor 8 7 1 4 3 2 5 6 ELECTRICAL ASSEMBLY: No. 1 2 3 4 5 Description No.
USE AND CARE INFORMATION: Operations: • Read and understand all instructions and warnings in this manual before operating the appliance. Save these instructions for future reference. • Always leave safety grills and filters in place. Without these components, operating fans could catch on to hair, fingers and loose clothing. • NEVER dispose cigarette ashes, ignitable substances, or any foreign objects into fans. • NEVER leave cooking unattended.