® Range Hood Ancona Chef GCC436 User Manual & Installation Instructions IMPORTANT SAFETY INSTRUCTIONS Carefully read the important information regarding installation, safety and maintenance. Keep these instructions for future reference.
Before You Begin INSTALLERS - Start Here Safety Instructions are on pages 4 and 5 and Installation Instructions are on pages 6 to 16. Please perform these steps: 1. Read the safety instructions. 2. Read all instructions in the Installation section of this manual BEFORE installing the range hood. 3. Remove all packing materials. 4. When finished, make sure to leave these instructions with the consumer. 5. Installation is to be done by a qualified technician only.
Table of Contents Before You Begin................................................................................................................................ 2 Table of Contents............................................................................................................................... 3 Important Safety Information............................................................................................................. 4 Included Parts..............................................
Important Safety Information READ ALL INSTRUCTIONS BEFORE USE Read and follow all instructions before using the range hood to prevent the risk of fire, electric shock, personal injury, or damage when using the range hood or appliances with the range hood. This guide does not cover all possible conditions that may occur. Always contact your service technician or manufacturer about problems that you do not understand.
Important Safety Information WARNING: TO REDUCE RISK OF A RANGE TOP GREASE FIRE: To reduce the risk of injury to persons in the event of a gas leaks: a) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings. • Extinguish any open flame. • DO NOT turn on the lights or any type of appliance. • Open all doors and windows to disperse the gas.
Included Parts Range Hood Damper Damper Gasket 4 x Screws / Washers Installation of Glass Canopy 4 x Damper Screws 2 x Upper Chimney Screws Upper Chimney Upper Chimney Bracket 2 x Filters Lower Chimney Hardware Note: For safety reasons, range hood mounting screws and anchors will not be included due to the variation of cabinetry constructions and wall material.
Range Hood Dimensions 6.3” (160 mm) This range hood fits standard ceilings up to 2.7m (9ft.) if installed at 816 mm (32-1/8 inches) above the cooking surface. 10.2 “ (260 mm) 15.9 “ (404 mm) 10.2 (259 “ mm) 13.6 “ (346 mm) 18.9 “ - 37.5” (480 mm - 954 mm) 11.5 “ (291.5 mm) 1.22 “ (31 mm) 18. 9“ (48 0m m) 23.14 “ (588 mm) 35.4“ (900 mm) 10.5” (266.
Installation STEP 1 Read the Safety Instructions • It is very important to read the safety instructions on pages 4 and 5. IMPORTANT: It is the installer’s responsibility to comply with installation clearances. STEP 2 Unpack Range Hood and Prepare Tools • Carefully unpack the range hood and parts. Make sure all parts are included as shown on page 6. • DO NOT remove the protective film covering the appliance until the installation is fully completed.
Installation STEP 5 Venting Installation Guidelines • The following steps are for exterior ventilation. • If you require a ductless installation, please visit anconahome.com to purchase a recirculation kit. IMPORTANT: • Vent system must terminate to the outside (roof or side wall). • DO NOT terminate the vent system in an attic or other enclosed area. • DO NOT use 4” (10.2 cm) laundry-type wall caps. • Use metal/aluminum vent only. A rigid metal/aluminum vent is recommended. • DO NOT use a plastic vent.
Installation STEP 6 Mark Placement of Range Hood Mounting Screws • Use a pencil to mark on the wall the desired placement of the range hood mounting screws. • Screw two wood screws (not provided) into wall. • Leave approximately 1/4” (6.3 mm) of the screw head protruding from the wall to allow clearance for mounting the range hood. • Use threaded drywall anchors when mounting the range hood onto sheet rock. Mounting the hood into wall studs or lumbars is highly recommended.
STEP 9 Connect Ductwork • Attach ductwork to damper. Secure the ductwork with duct tape to make sure joints are secure and air-tight. • Do not install the duct tape too tightly as this may prevent the damper flaps from opening which will overwork the motor and cause improper functioning of the unit. • Fasten all connections with sheet metal screws and tape all joints with certified aluminum or foil tape. Use caulking to seal exterior wall or roof opening around the cap.
Installation STEP 11 Install Glass Canopy and Lower Chimney • Place glass canopy piece on top of the main housing and secure in place with the four screws and rubber washers provided. • Place lower chimney on top of the main housing. STEP 12 Install Upper Chimney Bracket • Position the upper chimney bracket onto the wall directly below the ceiling. Align the upper chimney bracket with the range hood below. • Use a pencil to mark desired placement of the upper chimney bracket on the wall.
Installation STEP 13 Install Upper Chimney STEP 14 Install Filters • • Hold the baffle filter by the two knobs. • Place the front of the baffle against the interior front of the range hood. • Slide it up and push the rear of the filter back until it sits securely. • The baffle filters channel grease released by cooking foods into the grease trays and prevent flaming foods on the cook top from damaging the inside of the range hood.
Operation Using the Fan u Press to begin low speed. Screen will display 1. Press to increase speed suction. Screen will display increments as 2, 3, 4. Turning the Light On of Off u Press to turn light on and again to turn light off. v Press while light is on to have light turn off after “15 minutes”. Press again to stop suction. Screen will display 00. v Press to begin high speed suction. Screen will display 3. Press again to begin high speed suction to 4. Press again to stop suction.
Maintenance Replacing the Light Bulbs u Unplug the unit from the AC outlet. v Remove five screws from the light panel, then remove the light bulbs by popping them out. Cleaning the Range Hood Be sure electrical power is off and all surfaces are cool before cleaning or servicing any part of the hood. Range Hood Body • Do not use a steel wool pad; it will scratch the surface. • To clean the stainless steel surface, use warm soapy water or a stainless steel cleaner.
Please register your product warranty by visiting the Ancona Home website. Canada & USA Phone: 888-686-0778 Fax: 800-350-8563 Email: service@anconahome.com Website: www.anconahome.com Ancona is in association with Mr Appliance for all after sales service calls. Please contact their service provider or visit their website: Phone: 888-998-2011 Website: www.mrappliance.com MAAN1191-01 © 2016 Copyright of Ancona Home. All rights reserved.
