WALL MOUNTED RANGE HOOD USER INSTRUCTIONS WPR630 - WPR636 We recommend to put working gloves on to perform the installation as some edges may be sharp IMPORTANT SAFETY INSTRUCTIONS Carefully read the following important information regarding installation safety and maintenance. Keep these instructions for future reference.
Important Safety Notice Read all Instructions before Installing and operating this appliance • • • • • The installation in this manual is intended for qualified installers, service technicians or persons with similar qualified background. Installation and electrical wiring must be done by qualified professionals and in accordance with all applicable codes and standards, including fire-rated construction. DO NOT attempt to install this appliance yourself.
• • • Clean ventilating fan frequently. Always use appropriate cookware and utensils size. Always use cookware appropriate for the size of the surface element. To reduce the risk of injury to persons in the event of a stove top grease fire: • SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn OFF the burner. BE CAREFUL TO PREVENT BURNS. NEVER PICK UP A FLAMING PAN—you may be burned.
Parts Supplied : Qty: 6 + 1 pcs Hood mounting bracket Qty: 4 + 1 pcs Mounting hood to wall and upper chimney bracket to wall Qty: 6 + 1 pcs Qty: 4 + 1 pcs Mounting hood to wall and upper chimney bracket to wall 4
• • • • • • • Vent system must terminate to the outside (roof or side wall). DO NOT terminate the vent system in an attic or other enclosed area. DO NOT use 4” (10.2 cm) laundry-type wall caps. Use metal/aluminum vent only. Rigid metal/ aluminum vent is recommended. DO NOT use plastic vent. Always keep the duct clean to ensure proper airflow. Calculate the following figures before installation: 1. Distance from the floor to the ceiling. 2.
IMPORTANT: • A minimum of 6” round (standard for this range hood) or 3-1/4 x 10” rectangular duct (purchased separately) must be used to maintain maximum airflow efficiency. • Always use rigid type metal/aluminum ducts if available to maximize airflow when connecting to provided duct. • Please use Duct Run Calculation below to compute total available duct run when using elbows, transitions and caps. • ALWAYS, when possible, reduce the number or transitions and turns.
Venting methods: • • This range hood is factory set for venting through the roof or wall. Vent work can terminate either through the roof or wall. To vent through a wall, a 90° elbow is needed. IMPORTANT: • • • • NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside. Use metal/aluminum duct work only. Fasten all connections with sheet metal screws and tape all joints with certified Silver Tape or Duct Tape.
Electrical Requirements : IMPORTANT: Observe all governing codes and ordinances. It is the customer’s responsibility: Ŗ To contact a qualiſed electrical installer. If codes permit and a separate ground wire is used, it is recommended that a qualiſed electrician determine that the ground path is adequate. A 120-Volt, 60 Hz, AC-only, fused electrical supply is required on a separate 15-amp circuit, fused on both sides of the line. DO NOT ground to a gas pipe.
Preparation: Advanced Preparations: • Be familiar with the controls of the range hood by reading through Range Hood Operations, Page 12. • Place the range hood on a flat, stable surface. Connect the range hood to a designated standard outlet (120-Volt, 60Hz, AC only) and turn on the range hood. Verify all operations of the range hood by referring to Range Hood Operations, Page 12.
Installation: Installations (refer to Page 4 for parts): 1. Measure the distance between stove top and the bottom of range hood. A distance of 24” to 30” is recommended with a minimum of 30” for gas stove tops. 2. Using references in Height & Clearance on Page 5 and Measurements and Diagrams on Page 16, mark the leveling point of the hood. Position two mounting screws on the wall, leaving 1/8” space away from the wall. 3.
Installation (Continued): 8. Connect the range hood to a designated standard outlet (120-Volt, Figure 8 60Hz, AC only) or cut off the plug and connect three wires (black, white and green) to house wires and cap with wire connectors. Connect according to colors (i.e. black to black, white to white, and green to green). 9. Store excess wires in the wiring box. 10. Install both chimneys and tighten screws to secure the lower chimney to the range hood as shown in Figure 8. 11.
Range Hood Operations: Control Panel Layout and Buttons Configurations: LED Light Indicator Light Control LED Speed Indicators Speed Control Power Control (On/Off) This range hood is equipped with six electronic controls, oversized powerful centrifugal squirrel cage motor with stainless steel baffle filters and spacers, two bright 3 W LED lights. The six electronic buttons control the intensity of the Lights, Speeds (Quiet, Low, Medium and High) and Power (On/Off).
Range Hood Operations (Continued): Control Panel Layout and Buttons Configurations: Quiet Speed Low Speed Medium Speed LED Light Indicator LED Speed Indicators Light Control • High Speed Power Control (On/Off) During this 3-minutes delay, changing speeds will not affect the countdown. Immediate Power-off • While the fans are in 3-minute power-off delay mode, press the Power Control (On/Off) button once to turn OFF the fans immediately.
Troubleshooting 1. If the range hood or LED light does not operate after installation: Check if the range hood has been plugged in, make sure that all power has been turned back ON, fused not blown and all electrical wiring are properly connected. Swap out light assembly to working ones to determine whether it is caused by defective bulbs. See Replacing the light bulbs on Page 22. • 2.
Use and Care Information: Operations: • • • • • Read and understand all instructions and warnings in this manual before operating the appliance. Save these instructions for future reference. Always leave safety grills and filters in place. Without these components, operating blowers could catch on to hair, fingers and loose clothing. NEVER dispose cigarette ashes, ignitable substances, or any foreign objects into blowers. NEVER leave cooking unattended.
Measurements and diagrams: Installation ation Over ew:: Overvi view 16
• • All measurements in parenthesis are in centimeter. All inch measurements are converted from centimeters, thus inch measurements are estimated.
• • All measurements in parenthesis are in centimeters. All inch measurements are converted from centimeters, thus inch measurements are estimated.
Hood-mounting Bracket: Circuit Diagram: 19
Range Hood Assembly: No. 1 2 3 4 5 6 7 Description Hood Casing Hood-Mounting Bracket Power Cable Top Panel Motor Capacitor Control Bracket No.
Electrical Assembly: No. 1 2 3 4 5 Description Screws (3/16” x 3/8”) Electrical Box Cover Processor Board Screws (3/16” x 3/8”) Electrical Box Base No.
Maintenance: SAFETY WARNING: Never put your hand into area housing the fan while the fan is operating! For optimal operation, clean range hood and all baffle/spacer/filter/oil container regularly. Regular care will help preserve the appearance of the range hood. Cleaning Exterior surfaces: • • • • • • Clean periodically with hot soapy water and clean cotton cloth. DO NOT use corrosive or abrasive detergent (e.g.
