® Range Hood UCDI430 User Manual & Installation Instructions IMPORTANT SAFETY INSTRUCTIONS Carefully read the important information regarding installation, safety and maintenance. Keep these instructions for future reference.
Before You Begin INSTALLERS - Start Here Safety Instructions are on pages 4 and 5 and Installation Instructions are on pages 8 to 15. Please perform these steps: 1. Read the safety instructions. 2. Read all instructions in the Installation section of this manual BEFORE installing the range hood. 3. Remove all packing materials. 4. When finished, make sure to leave these instructions with the consumer. 5. Installation is to be done by a qualified technician only.
Table of Contents Before You Begin................................................................................................................................ 2 Table of Contents............................................................................................................................... 3 Important Safety Information............................................................................................................. 4 Included Parts..............................................
Important Safety Information READ ALL INSTRUCTIONS BEFORE USE Read and follow all instructions before using the range hood to prevent the risk of fire, electric shock, personal injury, or damage when using the range hood or appliances with the range hood. This guide does not cover all possible conditions that may occur. Always contact your service technician or manufacturer about problems that you do not understand.
Important Safety Information WARNING: TO REDUCE RISK OF A RANGE TOP GREASE FIRE: To reduce the risk of injury to persons in the event of a gas leaks: a) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings. • Extinguish any open flame. • DO NOT turn on the lights or any type of appliance. • Open all doors and windows to disperse the gas.
Included Parts Range Hood Rectangular Vent/Damper 3.25 x 10 in. (8.3 x 25.4 cm) Round vent/damper 6 in. (15.3 cm) 2 Filters 4 + 1 pieces mounting screws for vent/damper Hardware Note: For safety reasons, range hood mounting screws and anchors will not be included due to the variation of cabinetry constructions and wall material. Please consult your installation specialist regarding the optimal type of mounting screws and wall anchors to suit your home’s construction.
Range Hood Dimensions 8 . (70 n /8 i 27 7 9 12 in. ) mm 247 .( ¾ in ) mm in. 7 ¼ mm) (185 3 (9 ½ 0m in m. ) (30 in. 1 1/8mm) (28 5m 9 ¾ in. (247 mm) m) 3 1/8 in. (79 mm) 756 20 5/8 in. (525 mm) 29 12 in. .( ¾ in ) mm 1 1/8 7¼ ) mm 708 ( . m) n /8 i 50 m 27 7 6 in. (1 9 ¾ in. (247 mm) m) 38 m ( . in 1 ½ 9 ¼ in. (235 mm) (30 in. (1 m) 38 m ( . n i 1 ½ 9 ¼ in. (235 mm) in. 7 ¼ mm) (185 85 m m) 3 ½ in. (90 mm) 27 7/ 8 in. (708 in. (2 mm) 8 mm ) 9¾ in. (2 47 m m) 3 ½ in.
Installation STEP 1 Read the Safety Instructions • It is very important to read the safety instructions on pages 4 and 5. IMPORTANT: It is the installer’s responsibility to comply with installation clearances. STEP 2 Unpack Range Hood and Prepare Tools • Carefully unpack the range hood and parts. Make sure all parts are included as shown on page 6. • DO NOT remove the protective film covering the appliance until the installation is fully completed.
Installation STEP 5 Venting Installation Guidelines • The following steps are for exterior ventilation. IMPORTANT: • Vent system must terminate to the outside (roof or side wall). • DO NOT terminate the vent system in an attic or other enclosed area. • DO NOT use 4 in (10.2 cm) laundry-type wall caps. • Use metal/aluminum vent only. A rigid metal/aluminum vent is recommended. • DO NOT use a plastic vent. • Always keep the duct clean to ensure proper airflow.
Installation IMPORTANT: • A minimum of 6 in. (15.3 cm) round or 3-1/4 x 10 in. (8.3 cm x 25.4 cm) rectangular duct must be used to maintain maximum airflow efficiency. • Always use rigid type metal/aluminum ducts if available to maximize airflow when connecting to provided duct. • Please use Duct Run Calculation below to compute total available duct run when using elbows, transitions and caps. • ALWAYS, when possible, reduce the number or transitions and turns.
Installation STEP 6 Preparations NOTE: To avoid damage to your hood, prevent debris from entering the vent opening. • Determine and mark the centre line on the ceiling or wall where the range hood will be installed. • Make sure there is proper clearance within the ceiling or wall for exhaust vent. • Due to the weight and size of this unit, please make sure that the support system or framework being used is stable and secure in the ceiling or wall.
Installation Remove rear vent back plate • Position the unit face down on a flat non-abrasive surface with rear of product facing you. • Remove the back plate by removing the 4 screws (See Figure #5) SAFETY WARNING: Risk of electrical shock. This range hood must be properly grounded. Make sure this is done by a qualified electrician in accordance with all applicable national and local electrical codes.
Installation STEP 9 Install top vent plate and rear damper (For rear venting only) • Re-install the plate removed in step 7 to block top venting hole. • Put plate in position and put in 4 screws from step 7 (See Figure #10). • Install rectangular air damper outlet on the rear vent location (See Figure #11). • Connect duct work to damper. • Use Duct Tape to ensure joint is sealed and air tight. Fig #10 Fig #11 30 mm (1.18 in.) 90 mm (3.54 in.) 108 mm (4.25 in.) 280 mm (11 in.
#13 Installation Method 2: attach the ducting to the rear rectangular damper and exhaust outdoors. 30 mm 30 mm (1.18 in.) (1.18 in.) 90 mm 90 mm (3.54 in.) mmmm 108 108 in.)in.) (4.25(4.25 (3.54 in.) 280 mm (11 in.) 280 mm (11 in.) 708 mm (27.87 in.) 708 mm (27.87 in.) Fig #13 Fig #13 STEP 11 Fig #13 Attaching the unit under the kitchen cabinets • Mark or drill a small hole on the mounting position according to the space and dimensions cited on the following drawings.
Installation STEP 12 Connect to AC • 3-Pronged Plug Connect AC plug into a grounded AC outlet having 120V, 60Hz. Place the outlet at a maximum distance of 33-1/2 in. (851 mm) from where the cord exits on the hood. Ground Plug 3-Prong Receptacle IMPORTANT: • Observe all governing codes and ordinances. • It is the customer’s responsibility to contact a qualified electrical installer.
AYD -056B AYD -056B AYD -056B AYD -056B AYD -056B AYD -056B - -056B AYD - 056B AYD -056B AYD -056B AYD Operation AYDAYD - 013B - 013B AYD -056B AYD -056B AYD -056B AYD -056B AYD -056B AYD 056B AYD -056B AYD -013B AYD -013B AYD -013B Increase Power Lamp Auto Timer AYD -Decrease 013B AYD -056B (On/off) NOTE: When the hood has been initially connected to the Fan AYD -013B AYD -013B AYD -013B Power or after a Power Failure, all indicators turn ON for 1 AYD - 013B (with 3 speed setting) second then OFF, the hood
Maintenance Replacing the Light Pucks IMPORTANT: ALWAYS SWITCH OFF THE ELECTRICITY SUPPLY AT THE MAIN PANEL BEFORE CARRYING OUT ANY OPERATION ON THE APPLIANCE. u Make sure the range hood is unplugged or turn OFF breaker. w Replace with a 10.2 Volt, 2.5 Watt max, LED lights. Plug in new puck and push back into light panel. v Remove filters and push the spring, pull out the LED puck and unplug it. x Turn ON breaker and range hood to test for operation.
Maintenance Cleaning Filters IMPORTANT: Drain oil from baffles, spacers, filters, oil tunnels, oil containers before oil and residue overflow! • Remove all baffles, spacers, filters, grease tray, and oil containers and discard oil and residue. • Wash with warm soapy water. NOTE: Stainless steel baffles, spacers and oil tunnel are top rack dishwasher safe. • Dry thoroughly before replacing and follow directions for installation in reverse. • Filters should be cleaned after every 30 hours of use.
Range Hood Assembly Number Part 1 Power cord 2 Round duct or valve (Exhaust) 3 Rear vent back plate 4 Housing assembly 5 Bracket of switch 6 Switch plastic box 7 Switch board 8 Base of electronic box 9 PCB 10 Capacitor 11 Cover of electronic box 12 13 14 15 Blower assembly (includes motor) 16 — 19 — 17 Light panel 18 LED puck lights 19 Aluminum filter (2 pieces) 20 Damper flap (rectangle) 21 Vent (rectangle) 22 Screw bag
Motor Assembly AC 120V 60Hz Circuit Diagram AC 120V 60Hz CN2 CN3 Capacitor AC 120V 60Hz Main PCB CN1 CN4 CN2 + CN5 Main PCB CN6 CN1 CN4 CN5 CN2 CN6 Temperature / Humidity CN3Sensor CN8 Main PCB MAX 10.2V 250mA 2.5W (Optional) Temperature / Humidity Sensor (Optional) _ CH B LED Pucks + CN6 CN8 MAX 10.2V 250mA 2.5W CN5 Controls PCB L CN3 CN8 NCH B LED Pucks+ Capacitor E MAX 10.2V 250mA 2.
Use and Care Information Operations • Read and understand all instructions and warnings in this manual before operating the appliance. Save these instructions for future reference. • Always leave safety grills and filters in place. Without these components, operating fans could catch on to hair, fingers and loose clothing. • NEVER dispose cigarette ashes, ignitable substances, or any foreign objects into fans. • NEVER leave cooking unattended.
Please register your product warranty by visiting the Ancona Home website. Canada & USA Phone: 1-888-686-0778 Fax: 800-350-8563 Email: service@anconahome.com Website: www.anconahome.com Ancona is in association with Mr Appliance for all after sales service calls. Please contact their service provider or visit their website: Phone: 1-888-998-2011 Website: www.mrappliance.com MAAN1252-01 © 2019 Copyright of Ancona Home. All rights reserved.
