® Undercabinet Range Hood 30 in. with Night Light AN-1253 User Manual & Installation Instructions IMPORTANT SAFETY INSTRUCTIONS Carefully read the important information regarding installation, safety and maintenance. Keep these instructions for future reference.
Before You Begin INSTALLERS - Start Here Safety Instructions are on pages 4 to 6 and Installation Instructions are on pages 9 to 18. Please perform these steps: 1. Read the safety instructions. 2. Read all instructions in the Installation section of this manual BEFORE installing the range hood. 3. Remove all packing materials. 4. When finished, make sure to leave these instructions with the consumer. 5. Installation is to be done by a qualified technician only.
Table of Contents Before You Begin................................................................................................................................ 2 Table of Contents............................................................................................................................... 3 Important Safety Information............................................................................................................. 4 Included Parts..............................................
Important Safety Information READ ALL INSTRUCTIONS BEFORE USE Read and follow all instructions before using the range hood to prevent the risk of fire, electric shock, personal injury, or damage when using the range hood or appliances with the range hood. This guide does not cover all possible conditions that may occur. Always contact your service technician or manufacturer about problems that you do not understand.
Important Safety Information WARNING: TO REDUCE RISK OF A RANGE TOP GREASE FIRE: To reduce the risk of injury to persons in the event of a gas leaks: a) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings. • Extinguish any open flame. • DO NOT turn on the lights or any type of appliance. • Open all doors and windows to disperse the gas.
Important Safety Information WARNING: TO REDUCE RISK OF A RANGE TOP GREASE FIRE: 7. Two installers are recommended because of the large size and weight of this hood. 1. To reduce risk of fire and to properly exhaust air, be sure to duct air outside. Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages. 8. This product is equipped with a thermostat which may start blower automatically.
Included Parts Range Hood Vent-round Ø 6 in. (15.3 cm) Vent-rectangle 10 in. (25.4 cm) (Optional 14 in. (35.5 cm) available) 2 Filters Metal Inlet Cover Mounting Screws Vent (ST4 x 8 mm) 9 + 1 pieces Black Mounting Screws (ST4 x 8 mm) 4 + 1 pieces 3 pieces wire connector Hardware Note: For safety reasons, range hood mounting screws and anchors will not be included due to the variation of cabinetry constructions and wall material.
Range Hood Dimensions 30.5 in. ) 7 (29.9 n.) cm (9.8.2 cm m c i 8 76 . (3.2 i 13 cm ( n.) 35.2 24.7 in.) (7.2 2 in.) in.) 18.4 cm (7.2 in.) Ø cm 18.3 cm (1 8 cm (3.1 in.) 76 cm (29.9 in) 25 cm / 35.4 cm (9.8 in. / 13.9 in.) 51 cm (20 in .) 8 / 8.1 cm (3.1 / 3.1 in.
Installation STEP 1 Read the Safety Instructions • It is very important to read the safety instructions on pages 4, 5 and 6. IMPORTANT: It is the installer’s responsibility to comply with installation clearances. STEP 2 Unpack Range Hood and Prepare Tools • Carefully unpack the range hood and parts. Make sure all parts are included as shown on page 7. • DO NOT remove the protective film covering the appliance until the installation is fully completed.
Installation STEP 5 Venting Installation Guidelines • The following steps are for exterior ventilation. IMPORTANT: • Vent system must terminate to the outside (roof or side wall). • DO NOT terminate the vent system in an attic or other enclosed area. • DO NOT use 4 in (10.2 cm) laundry-type wall caps. • Use metal/aluminum vent only. A rigid metal/aluminum vent is recommended. • DO NOT use a plastic vent. • Always keep the duct clean to ensure proper airflow.
Installation IMPORTANT: • A minimum of 6 in. (15.3 cm) round or 3-1/4 x 10 in. (25.4 cm x 8.3 cm) rectangular duct must be used to maintain maximum airflow efficiency. • Always use rigid type metal/aluminum ducts if available to maximize airflow when connecting to provided duct. • Please use Duct Run Calculation below to compute total available duct run when using elbows, transitions and caps. • ALWAYS, when possible, reduce the number or transitions and turns.
Installation STEP 6 Preparations NOTE: To avoid damage to your hood, prevent debris from entering the vent opening. • Determine and mark the centre line on the ceiling or wall where the range hood will be installed. • Make sure there is proper clearance within the ceiling or wall for exhaust vent. • Due to the weight and size of this unit, please make sure that the support system or framework being used is stable and secure in the ceiling or wall.
Installation STEP 9 Attaching Vent • There are two venting ways, with two type of damper options, one is 6 inch (15.3 cm) round, another is 10 inch or 14 inch (25.4 or 35.5 cm) rectangle. NOTE: Please only punch the vent hole you want to use. Do not punch more than one vent hole, otherwise, the air power suction will be greatly affected. Top venting using 6 inch round damper: If you require 6 in. round venting, keep the unit as provided in the packaging and install the round damper provided.
Installation Top venting using rectangular damper: • If you require rectangular top (vertical) venting, simply install the rectangular damper provided (See Fig #7, #8 and #9). Use four screws (ST4 x 8 mm) to connect 10 inch damper or eight screws (ST4 x 8 mm) for 14 inch damper. For 10 inch rectangular vent, keep these two parts. For 14 inch rectangular vent, punch and remove as well.
Installation STEP 10 Installing the Hood Method 1: Attaching the unit to the wall • Remove eight screws (4 x 8 mm) holding cover pan to hood, see Fig #13 and #14. Fig #13 • Fig #14 Mark or drill four small holes on the mounting position according to the dimensions on Fig #15. Fig #15 • Insert four drywall anchors into the holes, and two screws into the top holes. • Hang the range hood onto the screws. • • Attach the ducting to the damper and exhaust outdoors.
Installation Method 2: Attaching the unit to under kitchen cabinets • Mark or drill four small holes on the mounting position according to the space and dimensions cited on the following image (Fig #18). • tighten the screws to cabinet. • Install two safety screws. • The following drawings show the mounting dimensions of the 30 in (750mm) and 36 in (900 mm). See Fig #18. Fig #18 • Fig #19 Re-assembly the cover pan, put the metal inlet cover onto the hood with four screws (4 x 8 mm).
Installation STEP 11 Venting • Depending on exterior ventilation chosen (see page 10), either exit the ducting through the ceiling or wall. • Always use rigid type metal/aluminum duct tube (follow the building codes in your area) to maximize airflow. Make sure that the backdraft flaps can open, to allow maximum airflow. Connect the duct tube to the vent/damper and securely seal with certified aluminum or foil tape so that it is air tight.
Installation STEP 12 Install Filters To install filters, follow four steps below (See Fig #23): • Angle the filter into slots at the back of the hood. • Push the button on handle of the filter. • Release the handle once the filter fits into a resting position. • Repeat to install all filters.
Operation Lamp Timer Speed Timer Lamp Power Speed NOTE: When the hood has been initially connected to the power or after a power failure, all indicators and LCD display turn ON for 1 second then OFF, the hood is in standby condition. a. Once the hood is connected with electricity, if wires for the control are not well connected or control board has poor connection or malfunction, buzzer will emit six beeps. You must then disconnect the hood, fix the problem and reconnect the hood. b.
Maintenance Replacing the Light Pucks IMPORTANT: ALWAYS SWITCH OFF THE ELECTRICITY SUPPLY AT THE MAIN PANEL BEFORE CARRYING OUT ANY OPERATION ON THE APPLIANCE. u Make sure the range hood is unplugged or turn OFF breaker. v Remove filters and easy clean panel, push the spring, pull out the LED puck and unplug it. CAUTION: PUCK MAY BE HOT, PLEASE TAKE OUT THE PUCK WHEN THE PUCK IS COMPLETELY COOL! w Replace with a 10.2 Volt, 2.5 Watt max, LED lights. Plug in new puck and push back into light panel.
Range Hood Assembly Range Hood Assembly Number Part Part Number 1 1Vent-round Vent-round kit kit 2 2Rectangle Rectangle outletoutlet 3 3 Housing assembly 4 Control bracket 5 Control board 6 Control box 7 Transformer 4 5 6 Housing assembly Control bracket Control board Control box 7 8Transformer Base of electronic box 8 of electronic box 9Base PCB 9 PCB Capacitor 10 10 11 Cover of electronic box Capacitor 11 12 box cover CoverWiring of electronic box 12 13 Slot 14 Bracket of mo
Assembly Circuit Diagram Motor Transformer AC 120V 60Hz CN1 CN5 Capacitor Controls PCB L N E CN10 CN4 Motor LED Pucks _ + Main PCB CN9 CN8 CN7 MAX 10.2V 250mA 2.
Troubleshooting Problem Light on, but motor does not work Cause The motor blocked Solution Get rid of the blocking The capacitor is damaged Have capacitor replaced The motor bearings are jammed or damaged Have motor replaced Light does not work, motor does Beside the mentioned above, check the following: not work Light is damaged Replace lights Oil leakage Hood body shakes Wires are loose or disconnected Connect the wires as per the electric diagram The one-way valve and the air ventilation entr
Use and Care Information Operations • Read and understand all instructions and warnings in this manual before operating the appliance. Save these instructions for future reference. • Always leave safety grills and filters in place. Without these components, operating fans could catch on to hair, fingers and loose clothing. • NEVER dispose cigarette ashes, ignitable substances, or any foreign objects into fans. • NEVER leave cooking unattended.
Please register your product warranty by visiting the Ancona Home website. Canada & USA Phone: 1-800-350-4562 Fax: 800-350-8563 Email: service@anconahome.com Website: www.anconahome.com Ancona is in association with Mr Appliance for all after sales service calls. Please contact their service provider or visit their website: Phone: 1-888-998-2011 Website: www.mrappliance.com © 2019 Copyright of Ancona Home. All rights reserved. This material may not be reproduced, displayed, modified or distributed.
Notes — 26 —