® Range Hood B328D and B336D 28 in. and 36 in. User Manual & Installation Instructions IMPORTANT SAFETY INSTRUCTIONS Carefully read the important information regarding installation, safety and maintenance. Keep these instructions for future reference.
Before You Begin INSTALLERS - Start Here Safety Instructions are on pages 4 and 5 and Installation Instructions are on pages 8 to 13. Please perform these steps: 1. Read the safety instructions. 2. Read all instructions in the Installation section of this manual BEFORE installing the range hood. 3. Remove all packing materials. 4. When finished, make sure to leave these instructions with the consumer. 5. Installation is to be done by a qualified technician only.
Table of Contents Before You Begin................................................................................................................................ 2 Table of Contents............................................................................................................................... 3 Important Safety Information............................................................................................................. 4 Included Parts..............................................
Important Safety Information READ ALL INSTRUCTIONS BEFORE USE Read and follow all instructions before using the range hood to prevent the risk of fire, electric shock, personal injury, or damage when using the range hood or appliances with the range hood. This guide does not cover all possible conditions that may occur. Always contact your service technician or manufacturer about problems that you do not understand.
Important Safety Information WARNING: TO REDUCE RISK OF A RANGE TOP GREASE FIRE: To reduce the risk of injury to persons in the event of a gas leaks: a) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings. • Extinguish any open flame. • DO NOT turn on the lights or any type of appliance. • Open all doors and windows to disperse the gas.
Included Parts Range Hood 2 Filters (28 in.) 3 Filters (36 in.) Damper flap Vent/Damper screws 4 + 1 pieces Hardware Note: For safety reasons, range hood mounting screws and anchors will not be included due to the variation of cabinetry constructions and wall material. Please consult your installation specialist regarding the optimal type of mounting screws and wall anchors to suit your home’s construction.
Range Hood Dimensions 17.7 m) / 5c in. (4 (65 .6 in. 25 Ø 5.9 in. (15 cm) cm) 10 in. (25.4 cm) 11.6 in 10.2 . (29. in. (2 6 cm ) 6 cm ) m) (86 c . n i ) .8 0 cm ) / 33 9 ( m . c n i (66 .4 9 in. ) / 35 m c 25.9 0 in. (7 27.5 0.4 in.
Installation STEP 1 Read the Safety Instructions • It is very important to read the safety instructions on pages 4 and 5. IMPORTANT: It is the installer’s responsibility to comply with installation clearances. STEP 2 Unpack Range Hood and Prepare Tools • Carefully unpack the range hood and parts. Make sure all parts are included as shown on page 6. • DO NOT remove the protective film covering the appliance until the installation is fully completed.
Installation STEP 5 Venting Installation Guidelines • The following steps are for exterior ventilation. IMPORTANT: • Vent system must terminate to the outside (roof or side wall). • DO NOT terminate the vent system in an attic or other enclosed area. • DO NOT use 4 in. (10.2 cm) laundry-type wall caps. • Use metal/aluminum vent only. A rigid metal/aluminum vent is recommended. • DO NOT use a plastic vent. • Always keep the duct clean to ensure proper airflow.
Installation IMPORTANT: • A minimum of 6 in. (15.3 cm) round or 3-1/4 x 10 in. (8.3 cm x 25.4 cm) rectangular duct (purchased separately) must be used to maintain maximum airflow efficiency. • Always use rigid type metal/aluminum ducts if available to maximize airflow when connecting to provided duct. • Please use Duct Run Calculation below to compute total available duct run when using elbows, transitions and caps. • ALWAYS, when possible, reduce the number or transitions and turns.
Installation STEP 6 Preparations NOTE: To avoid damage to your hood, prevent debris from entering the vent opening. • Determine and mark the centre line on the ceiling or wall where the range hood will be installed. • Make sure there is proper clearance within the ceiling or wall for exhaust vent. • Due to the weight and size of this unit, please make sure that the support system or framework being used is stable and secure in the ceiling or wall.
Installation STEP 9 Installing the hood • Remove the filters, halogen lights and the range hood cover. (See Fig #3) • Align range hood to the opening in the bottom of the cabinet and screw in with screws. (See Fig #4) Fig #3 Fig #4 STEP 10 Venting • Depending on the exterior venting chosen (See Page 10), either exit the ducting through the ceiling or wall. • Always use rigid type metal/aluminum duct tube (following the building codes in your area) to maximize airflow.
Installation IMPORTANT: • Observe all governing codes and ordinances. • It is the customer’s responsibility to contact a qualified electrical installer. • If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate. A 120-Volt, 60 Hz, AC-only, fused electrical supply is required on a separate 15-amp circuit, fused on both sides of the line. • DO NOT ground to a gas pipe.
Operation Stop Low Speed Medium Speed Power Settings Press the button once and the motor starts to operate at Low speed. u v Press the button speed. and the motor will reach Medium w Press the button speed. the motor will reach High x Press the button to turn the fan off. Lights u Press the light button and off.
Troubleshooting Problem Possible Cause If the range hood or halogen light Check if the range hood has been plugged in, make sure that does not operate after installation: all power has been turned back ON, fused not blown and all electrical wiring are properly connected. The range hood vibrates when the The range hood might not have been secured properly on to the blower is on: ceiling or wall. The blower or fan seems weak: Check that the duct sized used is at least 6 in. (15.3 cm) or 3-1/4 x 10 in. (8.
Maintenance Replacing the Light Bulbs IMPORTANT: ALWAYS SWITCH OFF THE ELECTRICITY SUPPLY AT THE MAIN PANEL BEFORE CARRYING OUT ANY OPERATION ON THE APPLIANCE. Removing old lightbulbs u v Installing new lightbulbs Make sure the range hood is unplugged or turn OFF breaker. u With your new lightbulb in one hand, ensure the bulb prongs are lined up with the wide ends of the two slots located in the socket. Remove filters.
Range Hood AssemblyNumber u v w 1 Number 2 Round 4 outlet assembly 3 Housing 5 assembly 6 8 Blower assembly (include 7 Blower assembly (includes motor) 8 9 Bracket of electronic box 10 of electronic Base of electronic box Bracket box 10 11of electronic Terminal Base boxconnector 11 Terminal 12 connector Capacitor 12 13 Capacitor 13 Cover of electronic box Cover of electronic box ak al 14 Cover of switch box 15 Switch board am 16 Bracket of switch 17 Panel 18 18 of light Brac
Assembly Assembly Circuit Diagram Circuit Diagram wer Assembly ssembly AC 12 0V 60Hz d tor M Grid Motor Push Button er Part t bi n d i n g p o s t L N E Capacitor ssembly Impeller bly peller wer t Blower Blower Assembly Wind drum inlet nd drum inlet d Number Part or 1 Grid 2 Motor eller 3 Impeller 4 Blower 5 Wind drum inlet wer Assembly ltrical Assembly nd drum inlet nlet u v w x y Assembly ber Electrical Part art Number Part u v w x 1 Bracket of electronic box Bracket
Use and Care Information Operations • Read and understand all instructions and warnings in this manual before operating the appliance. Save these instructions for future reference. • Always leave safety grills and filters in place. Without these components, operating fans could catch on to hair, fingers and loose clothing. • NEVER dispose cigarette ashes, ignitable substances, or any foreign objects into fans. • NEVER leave cooking unattended.
Please register your product warranty by visiting the Ancona Home website. Canada & USA Phone: 1-800-350-4562 Fax: 800-350-8563 Email: service@anconahome.com Website: www.anconahome.com Ancona is in association with Mr Appliance for all after sales service calls. Please contact their service provider or visit their website: Phone: 1-888-998-2011 Website: www.mrappliance.com MAAN1320-02 © 2019 Copyright of Ancona Home. All rights reserved.
