RANGE HOOD USER INSTRUCTIONS MODEL: IGCP430 30" IMPORTANT SAFETY INSTRUCTIONS Carefully read the following important information regarding installation safety and maintenance. Keep these instructions for future reference.
IMPORTANT SAFETY NOTICE READ ALL INSTRUCTIONS BEFORE INSTALLING AND OPERATING THIS APPLIANCE ● ● ● ● The installation in this manual is intended for qualified installers, service technicians or persons with similar qualified background. Installation and electrical wiring must be done by qualified professionals and in accordance with all applicable codes and standards, including fire-rated construction.
IMPORTANT SAFETY NOTICE READ ALL INSTRUCTIONS BEFORE INSTALLING AND OPERATING THIS APPLIANCE To reduce the risk of stove top grease fire: ● ● ● ● ● ● ● Keep all fans, filters, spacers, grease trays*, oil container* and grease-laden surfaces clean. Grease should not be allowed to accumulate on fan, filters, spacers, grease trays* and oil container*, and surfaces. Always turn range hood ON when cooking at high heat or when cooking flaming foods. Use high settings on cooking range only when necessary.
PARTS SUPPLIED: Hood body Decorative upper and lower chimneys (2 pcs) Mounting screws (8 pcs) Angle mounting brackets (8 pcs) Mounting screws (42 pcs) Ceiling mounting bracket (1 pc) Drywall anchors (12 pcs) Mounting screws (12 pcs) Explode screws (8 pcs) Nuts (26 pcs) Washers (26 pcs) `S` mounting hook (1 pc) 4 Filters (2 pcs)
VENTING REQUIREMENTS: • • • • • • • HEIGHT & CLEARANCE: Vent system must terminate to the outside (Roof or side wall). DO NOT terminate the vent system in an attic or other enclosed area. DO NOT use 4” (10.2 cm) laundry-type wall caps. Use metal/aluminum vent only. Rigid metal/ aluminum vent is recommended. DO NOT use plastic vent. Always keep the duct clean to ensure proper airflow. Calculate the following figures before installation: 1. Distance from the floor to the ceiling 2.
IMPORTANT: • • • • • • • • A minimum of 6” round or 3-1/4 x 10” rectangular duct (purchased separately) must be used to maintain maximum airflow efficiency. Always use rigid type metal/aluminum ducts if available to maximize airflow when connecting to provided duct. Please use Duct Run Calculation below to compute total available duct run when using elbows, transitions and caps. ALWAYS, when possible, reduce the number or transitions and turns.
VENTING METHODS: • • This range hood is factory set for venting through the roof or wall. Vent work can terminate either through the roof or wall. To vent through a wall, a 90° elbow is needed. IMPORTANT: • • • • NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside. Use metal/aluminum duct work only. Fasten all connections with sheet metal screws and tape all joints with certified Silver Tape or Duct Tape.
ELECTRICAL REQUIREMENTS: IMPORTANT: Observe all governing codes and ordinances. It is the customer’s responsibility to contact a qualified electrical installer. If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate. A 120-Volt, 60 Hz, AC-only, fused electrical supply is required on a separate 15-amp circuit, fused on both sides of the line. DO NOT ground to a gas pipe.
PREPARATIONS: Advanced Preparations: • Be familiar with the controls of the range hood by reading through Range Hood Operations, Page 15. • Place the range hood on a flat, stable surface. Connect the range hood to a designated standard outlet (120-Volt, 60Hz, AC only) and turn on the range hood. Verify all operations of the range hood by referring to Range Hood Operations.
INSTALLATION: Installations (refer to Page 4 for parts): NOTE: Use threaded drywall anchors only when mounting the hood on sheet rock. Mounting the hood on wall studs or lumbars is highly recommended. (See Fig. #1) (See Fig.
INSTALLATION CONTINUE: Step 3: Venting • Fix the damper on the top vent of hood with screws. (See Fig. #3) • Let the ducting pipe go inside through the hole from the ceiling. (See Fig. #4) • Measure the length of 6`` round metal duct required from the dampler / duct connector to the ductwork rough-in in the ceiling. Connect the duct to the damper / duct connector and seal with duct tape.
INSTALLATION CONTINUE: Step 5: Finishing installation • Slide the inner chimney up to the ceiling and attach it to the ceiling bracket using the screws. (See Fig. #7) • Remove the protective coating from the hood body and outer chimney. • Installation is finished. Fig # 7 Step 6: Installing filters • To install the filters, follow these four steps (See Fig. #8): • • • • Angle the filtters toward the back of the hood.
CONTROL PANEL OPERATION: Increase Speed Decrease Speed Timer Light Control Panel Layout and Buttons Configurations: Electronic Controls with Time Delay • Lights: • Press the light button • Power settings: to turn halogen lights on and off. • Press the button + once and the motor starts to operate at Low speed. • Press the button + again and the motor will reach Medium speed. • Press the button + once more and the motor will reach High speed.
REPLACING THE BULBS: Replacing the light bulbs: • This range hood uses halogen bulbs: 20W 12V type G4. • Make sure the range hood is unplugged or turn OFF breaker. • Place a flat-head screwdriver between light cover and housing to remove cover. • Gently pull defective bulb straight out and discard. • Wear a cotton glove or use a cloth to handle the replacement bulb. (DO NOT handle with bare fingers as this may shorten the life of the bulb). Push gently but securely into light socket.
MOUNTING BRACKETS: 15
MEASUREMENTS AND DIAGRAMS: 16
TROUBLE SHOOTING: 1) If the range hood or halogen light does not operate after installation: • Check if the range hood has been plugged in, make sure that all power has been turned back ON,fused not blown and all electrical wiring are properly connected. 2) The range hood vibrates when the blower is on: • The range hood might not have been secured properly on to the ceiling or wall. 3) The blower or fan seems weak: • Check that the duct sized used is at least 6” or 3-1/4 x 10”.
RANGE HOOD ASSEMBLY: No.
SPECIFICATIONS: Body design Stainless steel Power rating 120V / 60Hz (USA & Canada standard) cULus Certified General input power 290W (210W + 4x20W) Motor input power 210W Ampere 2.4A Levels of speed control 3 levels Airflow 420 CFM Noise Level (53.9db)/(60.3db)/(64.
BLOWER ASSEMBLY: No. Description 1 Grill 2 Blower Assembly 3 Impeller No. 4 Motor 5 6 Description ELECTRICAL ASSEMBLY: No. 1 2 3 4 5 Description Electrical box base PCB Electrical cover Capacitor Screw (ST3*10) No.
USE AND CARE INFORMATION: Operations: • Read and understand all instructions and warnings in this manual before operating the appliance. Save these instructions for future reference. • Always leave safety grills and filters in place. Without these components, operating fans could catch on to hair, fingers and loose clothing. • NEVER dispose cigarette ashes, ignitable substances, or any foreign objects into fans. • NEVER leave cooking unattended.
