® Range Hood WPR430 & WPR436 User Manual & Installation Instructions IMPORTANT SAFETY INSTRUCTIONS Carefully read the important information regarding installation, safety and maintenance. Keep these instructions for future reference.
Before You Begin INSTALLERS - Start Here Safety Instructions are on pages 4 and 5 and Installation Instructions are on pages 9 to 15. Please perform these steps: 1. Read the safety instructions. 2. Read all instructions in the Installation section of this manual BEFORE installing the range hood. 3. Remove all packing materials. 4. When finished, make sure to leave these instructions with the consumer. 5. Installation is to be done by a qualified technician only.
Table of Contents Before You Begin................................................................................................................................ 2 Table of Contents............................................................................................................................... 3 Important Safety Information............................................................................................................. 4 Included Parts..............................................
Important Safety Information READ ALL INSTRUCTIONS BEFORE USE Read and follow all instructions before using the range hood to prevent the risk of fire, electric shock, personal injury, or damage when using the range hood or appliances with the range hood. This guide does not cover all possible conditions that may occur. Always contact your service technician or manufacturer about problems that you do not understand.
Important Safety Information WARNING: TO REDUCE RISK OF A RANGE TOP GREASE FIRE: To reduce the risk of injury to persons in the event of a gas leaks: a) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings. • Extinguish any open flame. • DO NOT turn on the lights or any type of appliance. • Open all doors and windows to disperse the gas.
Included Parts Damper Main Housing Upper Chimney Bracket Lower Chimney Bracket Hood Mounting Bracket Lower Chimney Filters (x2) Upper Chimney 4 Screws (C) 4 Screws (D) Hardware Note: For safety reasons, range hood mounting screws and anchors will not be included due to the variation of cabinetry constructions and wall material. Please consult your installation specialist regarding the optimal type of mounting screws and wall anchors to suit your home’s construction.
Range Hood Dimensions WPR430 & WPR436 15.35 in. 30.7 in. (39 - 78 cm) 8.7 in. (22.3 cm) 6.8 in. (17.3 cm) 10.6 in. (27 cm) 1.96 in. (5 cm) 29 1/2 in. (75 cm) / 35.4 in. (90 cm) 19.6 in. (50 cm) Specifications Body Design Stainless Steel Power Rating 120 V / 60 Hz (cETLus Certified) Total Input Power 235.1 W (230 W + 2*2.55 W) Motor Input Power 230 W Amperage 1.
Mounting Brackets Upper Chimney Bracket 5 1/8” (13 cm) 1 3/8” (3.5 cm) 8 21/32 (22 cm) Lower Chimney Bracket 7 7/8” (20 cm) 5 1/8” (13 cm) 1 3/8” (3.5 cm) 8 5/8” (21.
Installation STEP 1 Read the Safety Instructions • It is very important to read the safety instructions on pages 4 and 5. IMPORTANT: It is the installer’s responsibility to comply with installation clearances. STEP 2 Unpack Range Hood and Prepare Tools • Carefully unpack the range hood and parts. Make sure all parts are included as shown on page 6. • DO NOT remove the protective film covering the appliance until the installation is fully completed.
Installation STEP 5 Venting Installation Guidelines • The following steps are for exterior ventilation. IMPORTANT: • Vent system must terminate to the outside (roof or side wall). • DO NOT terminate the vent system in an attic or other enclosed area. • DO NOT use 4 in. (10.2 cm) laundry-type wall caps. • Use metal/aluminum vent only. A rigid metal/aluminum vent is recommended. • DO NOT use a plastic vent. • Always keep the duct clean to ensure proper airflow.
Installation IMPORTANT: • A minimum of 6 in. (15.2 cm) round or 3-1/4 x 10 in. (25.4 cm x 8.3 cm) rectangular duct (purchased separately) must be used to maintain maximum airflow efficiency. • Always use rigid type metal/aluminum ducts if available to maximize airflow when connecting to provided duct. • Please use Duct Run Calculation below to compute total available duct run when using elbows, transitions and caps. • ALWAYS, when possible, reduce the number or transitions and turns.
Installation STEP 6 Preparations NOTE: To avoid damage to your hood, prevent debris from entering the vent opening. • Determine and mark the center line on the ceiling or wall where the range hood will be installed. • Make sure there is proper clearance within the ceiling or wall for exhaust vent. • Due to the weight and size of this unit, please make sure that the support system or framework being used is stable and secure in the ceiling or wall.
Installation STEP 10 Mount Range Hood Onto Wall • Hang the range hood on the hooks of the lower mounting bracket. (See Figure # 3) • Screw the range hood to the wall. CAUTION - Make certain the range hood is secure before releasing! Fig #3 STEP 11 Connect Ductwork • Attach ductwork to damper. Secure the ductwork with duct tape to make sure joints are secure and air-tight.
Installation STEP 13 Connect to AC • Connect AC plug into a grounded AC outlet having 120V, 60Hz. Place the outlet at a maximum distance of 33-1/2” (851 mm) from where the cord exits on the hood. • SEE IMPORTANT INSTRUCTIONS ON THIS PAGE. 3-Pronged Plug Ground Plug 3-Prong Receptacle IMPORTANT: • Observe all governing codes and ordinances. • It is the customer’s responsibility to contact a qualified electrical installer.
Installation STEP 14 Install Filters To install filters for the following four steps (See Figure # 6): • Angle the filter into slots at the back of the hood. • Push the button on handle of the filter. • Release the handle once the filter fits into a resting position. • Repeat to install all filters.
Operation 3 minute delay On / Speed Up LCD Power Settings Press the button + once and the motor starts to operate at Low speed. u v Press the button + again and the motor will reach Medium speed. w Press the button + once more and the motor will reach High speed. x Press the button - to lower speeds in succession until the motor stops working (power off).
Maintenance Replacing the Light Bulbs IMPORTANT: ALWAYS SWITCH OFF THE ELECTRICITY SUPPLY AT THE MAIN PANEL BEFORE CARRYING OUT ANY OPERATION ON THE APPLIANCE. u Make sure the range hood is unplugged or turn OFF breaker. x Replace with a 4 Volt, 2.5 Watt max, LED lights. Do not touch replacement bulb with bare hands! v w Open the filter and find the spring of the light. y Turn ON breaker and range hood to test for operation. Push the spring and the lights will slip out.
Range Hood Assembly Number 1 2 — 18 — Part Decorative filter LED light puck 3 Blower 4 Electrical box bracket 5 Electrical box base 6 PCB 7 Capacitor 8 Electrical box cover 9 10 Switch wire Power cord 11 Front panel 12 13 Lamp plate Rubber 14 Switch panel 15 Switch 16 Switch box 17 Switch box bracket 18 Shell 19 Back plate 20 Line plate 21 Line plate base 22 Hook 23 Top plate 24 Outlet 25 Outer chimney 26 Inner chimney 27 Outer chimney bracket 28 Inner chimn
Assembly Circuit Diagram Blower Assembly Number 1 2 Part Blower Wind Wheel Nut 3 Wind Wheel 4 Motor 5 Incabloc Rubber 6 Aluminum Cover 7 Plastic Wind Net 8 Sealing Gasket Electrical Assembly Number 1 2 Part Electrical Box Base PCB 3 Capacitor 4 Electrical box cover 5 Switch box 6 Switch — 19 —
Use and Care Information Operations • Read and understand all instructions and warnings in this manual before operating the appliance. Save these instructions for future reference. • Always leave safety grills and filters in place. Without these components, operating fans could catch on to hair, fingers and loose clothing. • NEVER dispose cigarette ashes, ignitable substances, or any foreign objects into fans. • NEVER leave cooking unattended.
Please register your product warranty by visiting the Ancona Home website. Canada & USA Phone: 1-800-350-4562 Fax: 800-350-8563 Email: service@anconahome.com Website: www.anconahome.com Ancona is in association with Mr Appliance for all after sales service calls. Please contact their service provider or visit their website: Phone: 1-888-998-2011 Website: www.mrappliance.com MAAN1501-EN-01 © 2017 Copyright of Ancona Home. All rights reserved.