® Range Hood WPNL630 and WPNL636 User Manual and Installation Instructions IMPORTANT SAFETY INSTRUCTIONS Carefully read the important information regarding installation, safety and maintenance. Keep these instructions for future reference.
Before You Begin INSTALLERS - Start Here Safety Instructions are on pages 4 and 5 and Installation Instructions are on pages 9 to 15. Please perform these steps: 1. Read the safety instructions. 2. Read all instructions in the Installation section of this manual BEFORE installing the range hood. 3. Remove all packing materials. 4. When finished, make sure to leave these instructions with the consumer. 5. Installation is to be done by a qualified technician only.
Table of Contents Before You Begin................................................................................................................................ 2 Table of Contents............................................................................................................................... 3 Important Safety Information............................................................................................................. 4 Included Parts..............................................
Important Safety Information READ ALL INSTRUCTIONS BEFORE USE Read and follow all instructions before using the range hood to prevent the risk of fire, electric shock, personal injury, or damage when using the range hood or appliances with the range hood. This guide does not cover all possible conditions that may occur. Always contact your service technician or manufacturer about problems that you do not understand.
Important Safety Information WARNING: TO REDUCE RISK OF A RANGE TOP GREASE FIRE: To reduce the risk of injury to persons in the event of a gas leaks: a) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings. • Extinguish any open flame. • DO NOT turn on the lights or any type of appliance. • Open all doors and windows to disperse the gas.
Included Parts Main Housing 30 in. Filters (x 2) 36 in. Filters (x 3) Lower Chimney Damper flap Hood Mounting Bracket Upper Chimney Bracket Upper Chimney 6 + 1 Screws Lower Chimney Bracket Hardware Note: For safety reasons, range hood mounting screws and anchors will not be included due to the variation of cabinetry constructions and wall material. Please consult your installation specialist regarding the optimal type of mounting screws and wall anchors to suit your home’s construction.
Range Hood Dimensions 17.2 cm (6.7 in.) 22.2 cm (8.75 in.) 43 - 84 cm (16.9 - 33 in.) 43 cm (16.9 in.) Ø15 cm (5.9 in.) 24.5 cm (9.6 in.) 3.5 cm (1.3 in.) 2.9 cm (1.1 in.) 50 cm (19.6 in.) 75 cm in.) / 5 . 9 2 ( 5.4 m (3 90 c Specifications Body Design Stainless Steel Power Rating 120 V / 60 Hz (cULus Certified) Total Input Power 405 W (400 W + 2 x 2.5 W) Motor Input Power 400 W Amperage 3.
Mounting Brackets Upper Chimney Bracket 4.96” (126 mm) 1.3” (35 mm) 8.58" (218 mm) Lower Chimney Bracket 7.99” (203 mm) 4.72” (120 mm) 1.5” (38 mm) 8.58” (218 mm) Mounting Bracket Hook 7.8” (200 mm) 3.9” (100 mm) 3.9” (100 mm) ” (66 mm) ” (66 mm) 8.6” (220 mm) —8— 0.
Installation STEP 1 Read the Safety Instructions • It is very important to read the safety instructions on pages 4 and 5. IMPORTANT: It is the installer’s responsibility to comply with installation clearances. STEP 2 Unpack Range Hood and Prepare Tools • Carefully unpack the range hood and parts. Make sure all parts are included as shown on page 6. • DO NOT remove the protective film covering the appliance until the installation is fully completed.
Installation STEP 5 Venting Installation Guidelines • The following steps are for exterior ventilation. IMPORTANT: • Vent system must terminate to the outside (roof or side wall). • DO NOT terminate the vent system in an attic or other enclosed area. • DO NOT use 4 in. (10.2 cm) laundry-type wall caps. • Use metal/aluminum vent only. A rigid metal/aluminum vent is recommended. • DO NOT use a plastic vent. • Always keep the duct clean to ensure proper airflow.
Installation IMPORTANT: • A minimum of 6 in. (15.3 cm) round or 3-1/4 x 10 in. (25.4 cm x 8.3 cm) rectangular duct must be used to maintain maximum airflow efficiency. • Always use rigid type metal/aluminum ducts if available to maximize airflow when connecting to provided duct. • Please use Duct Run Calculation below to compute total available duct run when using elbows, transitions and caps. • ALWAYS, when possible, reduce the number or transitions and turns.
Installation STEP 6 Preparations NOTE: To avoid damage to your hood, prevent debris from entering the vent opening. • Determine and mark the center line on the ceiling or wall where the range hood will be installed. • Make sure there is proper clearance within the ceiling or wall for exhaust vent. • Due to the weight and size of this unit, please make sure that the support system or framework being used is stable and secure in the ceiling or wall.
Installation STEP 9 Venting • Fix the damper flap on the top vent of hood. • If ventilation system is equipped with an external air duct with a different diameter, apply a reduction fitting. However, for maximum performance and safety, a 6 in. round ducting is recommended. Fig #2 STEP 10 Mount Range Hood onto Wall • Hang the range hood on the hooks of the hood mounting bracket. (See Figure #3) • Screw the range hood to the wall.
Installation IMPORTANT: • Observe all governing codes and ordinances. • It is the customer’s responsibility to contact a qualified electrical installer. • If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate. A 120-Volt, 60 Hz, AC-only, fused electrical supply is required on a separate 15-amp circuit, fused on both sides of the line. • DO NOT ground to a gas pipe.
Installation STEP 14 Install Filters To install filters for the following four steps (See Figure #7): • Angle the filter into slots at the back of the hood. • Push the button on handle of the filter. • Release the handle once the filter fits into a resting position. • Repeat to install all filters.
AYD -056BAYD -056B AYD -056B AYD -056B Operation AYD -056B AYD - 056B AYD -056B AYD -056B AYD -056B AYD -056B AYD --056B AYDAYD - 013B - 013B AYD -056B AYD -056B AYD -056B AYD - 056B Decrease Increase Timer Lamp Power AYD AYD AYD AYD--013B 056B AYD--013B 056B AYD--013B 056B Speed Speed AYD -013BAYD -056B AYD -056B AYD - 056B AYD -056B NOTE: When the hood has been initially connectedAYD to the- 056B Fan Power or after a Power Failure, all indicators turnAYD ON AYD for 1 - 056B - 056B (with 5 speed setting)
Maintenance Replacing the Light Pucks IMPORTANT: ALWAYS SWITCH OFF THE ELECTRICITY SUPPLY AT THE MAIN PANEL BEFORE CARRYING OUT ANY OPERATION ON THE APPLIANCE. u Make sure the range hood is unplugged or turn OFF breaker. w Replace with a 10.2 Volt, 2.5 Watt max, LED lights. Plug in new puck and push back into light panel. v Remove filters, push the spring, pull out the LED puck and unplug it. x Turn ON breaker and range hood to test for operation.
Range Hood Assembly Number 1 Part Upper Chimney 2 Lower chimney 3 Upper chimney bracket 4 Lower chimney bracket 5 Hood mounting bracket 6 Round duct or Valve (Exhaust) 7 Power cord 8 Housing assembly 9 Cover of control box 10 Control board 11 Front board 12 Rear bracket 13 Base of electronic box 14 PCB 15 Capacitor 16 Cover of electronic box 17 18 19 Blower assembly (includes motor) 20 21 LED puck lights 22 Baffle filter (2 or 3 pcs) 23 Screw bag — 18 —
Assembly Circuit Diagram Motor AC 120V 60Hz CN1 CN4 Capacitor CN2 CN3 Main PCB CN5 _ CH B LED Pucks CN8 + CN6 MAX 10.2V 250mA 2.
Use and Care Information Operations • Read and understand all instructions and warnings in this manual before operating the appliance. Save these instructions for future reference. • Always leave safety grills and filters in place. Without these components, operating fans could catch on to hair, fingers and loose clothing. • NEVER dispose cigarette ashes, ignitable substances, or any foreign objects into fans. • NEVER leave cooking unattended.
Please register your product warranty by visiting the Ancona Home website. Canada & USA Phone: 1-800-350-4562 Fax: 800-350-8563 Email: service@anconahome.com Website: www.anconahome.com Ancona is in association with Mr Appliance for all after sales service calls. Please contact their service provider or visit their website: Phone: 888-998-2011 Website: www.mrappliance.com MAAN1505-01 © 2018 Copyright of Ancona Home. All rights reserved.
Notes — 22 —
