Installation Guide

ManualsBrandsAndersen ManualsDoors & Windows32 in. x 80 in. 3000 Series White Right-Hand Self-Storing Easy Install Aluminum Storm Door with Brass Hardware

for Andersen

1-1/4” Fullview Storm Doors

Installation Guide

Please Do Not Return Product to Store!

EMCO Enterprises, Inc.

PO Box 853

Des Moines, IA 50306-0853

Rev 8-2011 11055

P/N 620357

with any questions regarding installation, mis-cut part replacement, lost part replacement, or anything else related to

your storm door purchase.

• If your abilities do not match the requirements of this installation, contact an experienced contractor.

• Andersen has no responsibility in regard to the post-manufactured assembly and installation of Andersen products.

PLEASE call the storm door Solution Center at 1-800-933-3626

EMCO Enterprises, Inc., is a wholly owned subsidiary of Andersen Corporation. EMCO

manufactures and supports the limited warranties for Andersen® and EMCO® doors.

“Andersen”, “EMCO” and all other marks where denoted are trademarks of Andersen

PARTS OVERVIEW

Your storm door should contain the

following parts:

Figure 1

Rain Cap

Door Frame

Hinge Rail with 4 hinges

(Hinge Side Z-bar)

Glass panel

Side Retainers (2)

Top & bottom Retainers (2)

Latch Rail

(Handle Side Z-bar)

Sweep

Sweep Fin

Side Screw Covers (2)

Top Screw Cover (1)

Not Shown

Shipping Clip

Door Mounting Screw Bag

Handle Set Kit

Closer Kit

Insect Screen

Your storm door should contain the

following parts:

Summary of content (10 pages)

PAGE 1
Installation Guide for Andersen® 1-1/4” Fullview Storm Doors Please Do Not Return Product to Store! PLEASE call the storm door Solution Center at 1-800-933-3626 with any questions regarding installation, mis-cut part replacement, lost part replacement, or anything else related to your storm door purchase. • If your abilities do not match the requirements of this installation, contact an experienced contractor.
PAGE 2
SAFETY FIRST - Please read and follow all warnings and cautions in this guide. warning Entry door hardware and handle may become hot when exposed to sunlight. warning Improper use of hand or power tools could result in injury and/or product damage. Follow equipment manufacturer’s instructions for safe operation. Always wear safety glasses. warning Windows and doors can be heavy.
PAGE 3
2. INSTALLATION PREPARATION: In this step, you will remove the insect screen and shipping clip. interior side up . Lay the door flat on a protected surface with the exterior side down. 14 TIP: Lay on door carton. 2. Remove the insect screen by lifting it up and then away from the shipping clip (Figure 5). 3. Remove and properly discard the shipping clip. CARTON 2 10 Figure 5 In this step, you will remove the side retainers and glass panel. interior side up 4.
PAGE 4
3. PREPARE STORM DOOR FOR HANGING 1 - #8x1” Tools needed: 8 - #8x1/2” 1/8” LEFT HINGE - Exterior View (Figure 9) In this step, you will hang the rain cap against the top mounting surface (Figure 9). 11 11 RIGHT HINGE - Exterior View (Figure 9) . Center the rain cap in the door opening. 2. Using a pencil, mark the hinge 3. 4. 5. 1 6. Figure 9 side hole on the mounting surface. Set rain cap aside. Using the drill and 1/8” drill bit, drill a hole in the mounting surface.
PAGE 5
4. HANG HINGED STORM DOOR Tools needed: 14 - #8x1” 11 1/8” LEFT HINGE - Exterior Views In this step, you will hang the storm door in the opening. RIGHT HINGE - Exterior Views . Position the door in the opening so that the edge of the hinge rail is flush with the end of the rain cap, and the top end of the hinge rail is butted up against the underside of the rain cap (Figure 13). 2.
PAGE 6
5. INSTALL REMAINING FRAME COMPONENTS 8 - #8x1” Tools needed: 11 1/8” LEFT HINGE - Exterior Views In this step, you will finish fastening the rain cap to the top mounting surface. RIGHT HINGE - Exterior Views . Close the storm door. 2. Adjust the rain cap so that the 1 1 gap between the rain cap and door frame is the same along the entire length of the rain cap. 3. Using the 1/8” drill bit, drill holes in the mounting surface through the pre-drilled holes in the rain cap (Figure 18). 4.
PAGE 7
6. INSTALL HANDLE SET In this step, you will install the handle set. . Refer to the instructions included in the handle set box to install the door handles. You can match your Andersen storm door lock to Schlage® or Kwikset® entry door locks. See handle set instructions contained within handle set box for details. “Kwikset” is a registered trademark of Newfry LLC. “Schlage” is a registered trademark of Schlage Lock Company. 7.
PAGE 8
. INSTALL WEATHER SEALING COMPONENTS Tools needed: 2 - #8x1/2” 11 1/8” LEFT HINGE - Interior Views In this step, you will install the bottom sweep components. RIGHT HINGE - Interior Views . Slide the sweep fin into the track 8 2. 7 3. 4. 5. 8 6. 7. Figure 24 8. located on the bottom of the door sweep (Figure 24). Using scissors, trim any excess sweep fin material that extends beyond the door sweep.
PAGE 9
. INSTALL CLOSER 4 - #10x2” Tools needed: 2 - #12x5/8” 5/32” LEFT HINGE - Interior Views In this step, you will install a jamb bracket onto the door jamb at the bottom (Figure 26). 3 2 1/4” 5 5/8” . Measure 5/8” below the window 2. 3. 4. 13 5. 7 Figure 26 6. 7. opening at the bottom on the hinge side and mark a line on the sweep or door frame. Extend the line onto the door jamb. Center the jamb bracket on this line, placing it 1/4” behind the hinge rail.
PAGE 10
. ADJUST THE CLOSER Tools needed: LEFT HINGE - Interior Views SLOWER FASTER Figure 29 In this step, you will adjust the door closer. Locate the adjustment screw at the end of the closer that attaches to the door frame (Figure 29). 1. Open the door and then let it close to note the speed at which the door closes. 2. Using a Phillips head screwdriver to adjust the closer to the desired speed: • For a faster closing speed, turn the adjustment screw to the left (counterclockwise).