Installation Guide

6
1. To attach window latch, located in
window handle kit (O), rst lower
venting window so pre-drilled
holes below the screen are at a
comfortable working height.
2. Align holes in window latch,
insect screen pull, and ventilating
window, then attach with two 3/4”
screws.
e
INSTALL RAIN CAP
EXTENDER, SCREW
COVERS, & WINDOW
HANDLE
(Left Hand)
5
K
Tools needed:
1/8”
!
!
1/2”
1/2”
1/2”
1”
1 1/2”
2”
1 1/2”
5/8”
5/8”
1”
x 3
3/4”
O
#8
#10
#12
#6
3/4” Machine Pan Painted
1/2” SMS Pan
1/2” SMS Pan Painted
1/2” SMS Flathead
1/2” Self-Drill Pan
1/2” Self-Drill Pan Painted
3/4” Machine Flathead
7/8” Machine Pan Painted
1” SMS Pan
1” SMS Pan Painted
1” Machine Pan Painted
1-1/2” Machine Flathead
1-1/2” Machine Flathead
2” SMS Pan Painted
5/8” SMS Pan Painted
1-1/4” SMS Pan
#8
#10
#12
#6
3/4” Machine Pan Painted
1/2” SMS Pan
1/2” SMS Pan Painted
1/2” SMS Flathead
1/2” Self-Drill Pan
1/2” Self-Drill Pan Painted
3/4” Machine Flathead
7/8” Machine Pan Painted
1” SMS Pan
1” SMS Pan Painted
1” Machine Pan Painted
1-1/2” Machine Flathead
1-1/2” Machine Flathead
2” SMS Pan Painted
5/8” SMS Pan Painted
1-1/4” SMS Pan
i
i
i
VIEW
!
!
1/2” 1/2”
1/2”
1”
1 1/2”
2”
1 1/2”
5/8”
5/8”
a
X
X
XX
VIEW
1. Lock leg of screw cover (K) into short leg of rain cap
screw track. Press on other leg to snap it into long
leg of track. Make sure screw cover snaps into screw
track along the entire length of the rain cap.
2. Repeat this process with remaining side screw covers.
K
K
X
X
XX
VIEW
c
b
X
X
XX
VIEW
B
SHORT LEG
PESTAÑA CORTA
RAINURE COURTE
I
If necessary, adjust the sweep (E).
1. Close the storm door.
2. From the interior, loosen the sweep screws
with a phillips screw driver. Adjust the
sweep up or down until the sweep n
lightly comes into contact with the door sill.
3. Retighten the sweep screws.
d
BOTTOM
PARTE INFERIOR
BAS
i
i
VIEW
E
I
3/16” Plug
x 1
1
2
3
12
9
4
13
14
5
6
7
8
NO 1
1. Look at the center hole of the rain cap. If the mounting surface can be
seen in the entire hole, proceed to step a2. If the mounting surface
cannot be seen in the entire hole, or if there is space above the rain
cap, then completely insert the 3/16” plug into the middle hole, then
proceed to step b.
2. Using the drill bit and three 1” screws, fasten the rain cap to the
mounting surface, then proceed to step c.
1. If a plug was installed in the middle hole, you will need
to install the rain cap extender (I).
2. Place the rain cap extender over the rain cap as shown,
with both ends being ush.
3. Using the drill bit and three 1” screws bag, fasten the
rain cap extender to the mounting surface.