Installation Guide

ManualsBrandsAndersen ManualsKitchen3000 Series 36 in. White Fullview Etched Glass Easy Install Storm Door

Your storm door should contain the

following parts:

for Andersen

1-1/2” Fullview Storm Doors

Installation Guide

Please Do Not Return Product to Store!

EMCO Enterprises, Inc.

PO Box 853

Des Moines, IA 50306-0853

Rev 1-2012 12001

P/N 618831

with any questions regarding installation, mis-cut part replacement, lost part replacement, or anything else related to

your storm door purchase.

• If your abilities do not match the requirements of this installation, contact an experienced contractor.

• Andersen has no responsibility in regard to the post-manufactured assembly and installation of Andersen products.

PLEASE call the storm door Solution Center at 1-800-933-3626

EMCO Enterprises, Inc., is a wholly owned subsidiary of Andersen Corporation. EMCO

manufactures and supports the limited warranties for Andersen® and EMCO® doors.

“Andersen”, “EMCO” and all other marks where denoted are trademarks of Andersen

PARTS OVERVIEW

Door Frame Assembly

- Rain Cap

- Latch Rail

- Hinge Rail

- Sweep

- Handle Clip

- Spacer Clips (2)

- Bottom spacer

Short Mounting Flange

Tall Mounting Flange

Top & Bottom Retainers (2)

Decorative Trim Plate (optional -

included on some models)

Screw Covers (3)

Not Shown

Shipping Clip

Insect Screen

Handle Set Kit

Closer Kit

Figure 1

Summary of content (11 pages)

PAGE 1
E Installation Guide for Andersen® 1-1/2” Fullview Storm Doors Please Do Not Return Product to Store! PLEASE call the storm door Solution Center at 1-800-933-3626 with any questions regarding installation, mis-cut part replacement, lost part replacement, or anything else related to your storm door purchase. • If your abilities do not match the requirements of this installation, contact an experienced contractor.
PAGE 2
SAFETY FIRST - PLEASE READ AND FOLLOW ALL WARNINGS AND CAUTIONS IN THIS GUIDE. WARNING Entry door hardware and handle may become hot when exposed to sunlight. WARNING Improper use of hand or power tools could result in injury and/or product damage. Follow equipment manufacturer’s instructions for safe operation. Always wear safety glasses. WARNING Windows and doors can be heavy.
PAGE 3
2. INSTALLATION PREPARATION: Tools needed: 3 - #8x1/2” LEFT HANDED In this step, you will confirm your storm door hinges on the correct side. RIGHT HANDED 1. Confirm your storm door hinges correctly by using your measurements from step 1 and comparing your door to figures 5 and 6. If your door came with a decorative trim plate, you will attach it to the exterior of your door in this step. NOTE: Some models include an optional decorative trim plate for the bottom exterior of the door.
PAGE 4
3. HANG HINGED STORM DOOR Tools needed: 20 - #8x1” 1/8” In this step, you will place the door in the opening and fasten it to the mounting surface. 1. Set bottom of door into opening, centering it in the opening. Ensure orange bottom spacer is sitting on door sill (Figure 9). 2. Tip the top of the door into the opening while ensuring the bottom of the door frame rests on the orange spacer (Figure 9).
PAGE 5
4. REMOVE INSTALLATION CLIPS AND PROTECTIVE FILM Tools needed: LEFT HANDED - EXTERIOR VIEWS 3 In this step, you will remove and properly discard all orange installation clips. 1. Grasp handle clip and pull away from latch rail to remove. (Figure 13) 2. Fill holes in latch rail with color matched plugs. RIGHT HANDED - EXTERIOR VIEWS 3 6 6 Figure 13 Figure 13 TIP: Use a screw driver to loosen and tighten screws in Steps 3 and 4; a drill may strip the screw holes.
PAGE 6
5. INSTALL HANDLE SET Tools needed: 2- #8 x 1 1/2” LEFT HANDED - EXTERIOR VIEWS 1 G L A S S 1- #10 x 1 1/2” In this step, you will install the handle set. 1. Look into handle holes on door to make sure lock case is oriented properly. The notch in the square spindle hole should be facing away from the glass panel.
PAGE 7
6. INSTALL RAIN CAP MOUNTING FLANGE, SCREW COVERS, AND WINDOW RETAINERS Tools needed: 2 - #8x1” 1/8” LEFT HANDED - EXTERIOR VIEWS In this step, you will install one of the two rain cap mounting flanges provided. 1. Choose the rain cap mounting flange that best covers the gap present above the rain cap. 2. Hook rain cap mounting flange to rain cap. (Figure 22) 3. While hooked, push up on rain cap mounting flange and use the 1/8” drill bit to drill a hole in the mounting surface through holes in flange.
PAGE 8
7. INSTALL CLOSERS 2- 6 - #10x2” Tools needed: 2- 4 - #12x5/8” LEFT HANDED - INTERIOR VIEWS In this step, you will install the door closers. RIGHT HANDED - INTERIOR VIEWS 1. Attach closer door bracket to the door through the two pre-drilled holes using two #12 x 5/8” screws. (Figure 28) 17 17 Figure 28 4 17 Figure 29 Figure 28 2.
PAGE 9
ADJUSTMENTS Tools needed: LEFT HANDED - INTERIOR VIEWS RIGHT HANDED - INTERIOR VIEWS In this step, you will adjust the door closer speed. 1. Locate the adjustment screw at the SLOWER FASTER Figure 33 Figure 34 OPENS WIDER end of the closer that attaches to the door frame (Figure 33). 2. Open the door and then let it close to note the speed at which the door closes. 3.
PAGE 10
TROUBLESHOOTING LEFT HANDED - INTERIOR VIEWS RIGHT HANDED - INTERIOR VIEWS If your bottom spacer falls off or is out of position prior to fastening the door to the mounting surface, follow the steps below to re-attach it to the door. 1. Hook the clip on to the sweep (Figure 36) 2. Rotate the clip until it snaps over the back of the sweep (Figure 37) 3. Slide the clip until it is touching the sweep screw on the handle side of the door.
PAGE 11
REGULAR MAINTENANCE WINDOW GLASS – The glass may be cleaned with any household glass cleaner. Keep glass cleaners away from painted parts and brass/nickel components. For help removing and installing the window and/or insect screen please see our website or call 1-800-933-3626 for assistance. PLASTIC PARTS – Plastic door components may be cleaned by using a mild soap and water mixture and by gently rubbing the affected area. Do not use harsh abrasives or any product that contains chlorine.