Instructions / Assembly

ManualsBrandsAndersen ManualsDoors & Windows4000 Series 36 in. x 80 in. Charcoal Gray Left-Hand Full View Interchangeable Aluminum Storm Door

Andersen Storm Door Division is a wholly owned subsidiary of Andersen Corporation. Andersen

Storm Door Division manufactures and supports the limited warranties for Andersen® and

EMCO® storm doors. “Andersen” and “EMCO” and all other marks where denoted are trademarks

Andersen SDD, PO Box 853

Des Moines, IA 50306-0853

02-2019 r 15043 Print in Color

p/n 902313

for Andersen® 1-1/2” Fullview Storm Doors with Standard or

Insulating Glass Panels and Integrated Close System

Installation Guide

Door Frame Assembly:

Rain Cap

Rain Cap Extender

Integrated Closer System

Latch Rail

Hinge Rail

Sweep

Handle Clip

Spacer Clips (2)

Bottom Spacer

Glass Panel

Screw Covers (3)

Rain Cap End Plug (2)

Not Shown

Handle Set Kit

Installation Kit

Insect Screen Panel

PARTS OVERVIEW

Figure 1

Your installation kit should contain the following

parts. However, in some door models, not all of the

parts will be used.

Please Do Not Return Product to Store!

with any questions regarding installation, lost part replacement, or anything else related to your storm door purchase.

Read this entire guide before you begin your installation. If your abilities do not

match the requirements of this installation, contact an experienced contractor.

PLEASE call the storm door Solution Center at 1-800-933-3626,

Summary of content (14 pages)

PAGE 1
Installation Guide E for Andersen® 1-1/2” Fullview Storm Doors with Standard or Insulating Glass Panels and Integrated Close System Please Do Not Return Product to Store! PLEASE call the storm door Solution Center at 1-800-933-3626, with any questions regarding installation, lost part replacement, or anything else related to your storm door purchase. Read this entire guide before you begin your installation.
PAGE 2
SAFETY FIRST: Please read and follow all Cautions and Warnings in this guide. WARNING WARNING Follow manufacturers' instructions for hand and power tools. Always wear safety glasses. Failure to do so could result in injury, product or property damage. Windows and doors can be heavy. Use safe lifting techniques and a reasonable number of people with enough strength to lift, carry, and install window and door products. Heavier windows and doors will require mechanical assistance.
PAGE 3
2 INSTALLATION PREPARATION ! I J ! Spacer Clips b ” ” /2” Figure 4 INTERIOR VIEW = EXTERIOR VIEW = i X VIEW VIEW X VIEW VIEW 11 MOUNTING SURFACE Tape Measure i 5/8 BRICKMOULD (EXTERIOR TRIM) Pliers Bottom Spacer 5/8 a Tools needed: 1/2 ” 1/2 ” 11 /2” 40 1/2" Figure 5 2” MIN. 3 1/8" 1/2 ” Figure 6 TO DOOR SILL 1. Most homeowners prefer to have the storm door In this step, you will confirm that your storm door hinges on the correct side.
PAGE 4
1/2” Self-Drill Pan Painted For a Right Hand Installation, 5/8” go to Page 9. 3 a HANG HINGED STORM DOOR AND REMOVE SPACER CLIPS (Left Hand) I H 1/2” 1/2” 3/4” Machine Flathead J Tools needed: 1” 2” 1 1/2” 7/8” Machine Pan Painted Handle Clip X LEFT HAND HINGED INSTALLS ONLY FOR RIGHT HAND HINGED INSTALL, SEE PG.
PAGE 5
1/2” 1/2” 1” SMS Pan Painted 1” Machine Pan Painted ! 1/2” #10 b 1-1/2” Machine Flathead #12 LOCK CASE TRIM PLATE LOCK Pan CASE Painted 1. With handle levers held horizontal, install both handle assemblies onto door. Spindle will pass through square hole in lock case and into other handle. 2. Install lock bar latch to lock bar. Spindle of lock bar latch will fit into the hole in the lock bar. 3. Attach interior and exterior trim plates together using two 1 1/2” pan head screws.
PAGE 6
1/2” Self-Drill Pan Painted 5/8” INSTALL RAIN CAP EXTENDER AND SCREW COVERS (Left Hand) 5 C L 3/4” Machine Flathead Tools needed: M 1” 2” 1 1/2” 7/8” Machine Pan Painted Rain Cap Extender (optional) a 1/2” 1/2” b OPTIONAL OPTIONAL 1 1/2” Screw 1” SMS Covers Pan End Cover 1/8" 1" 1” SMS Pan Painted c ! L 1” Machine Pan Painted C (optional) x3 ! 1-1/2” Machine Flathead 5/8” #10 1-1/2” Machine Flathead L 5/8” 1/2” 2” SMS Pan Painted 1.
PAGE 7
6 INSTALL THE GLASS OR INSECT SCREEN PANEL (Left Hand) i a VIEW i b i c VIEW VIEW SNUGGER BAR WARNING The glass panel/insect screen is secured in door frame by door handle locking mechanism. Once door handle has been rotated up to vertical position, the glass panel /insect screen are no longer secured in door frame. Immediately remove glass panel/insect screen from door frame after releasing locking mechanism. Failure to do so could result in injury and/or product damage.
PAGE 8
5/8” 8 TROUBLESHOOTING (Left Hand) 1/2” 5/8” For additional help with these, or any other 1 1/2” installation steps, please call our Solution Center at 1-800-933-3626. 1/2” Tools needed: 1/2” 1” 2” 1/8” 1 1/2” i a VIEW J ! b A i VIEW 1. Hook the clip on to the sweep 2. Rotate clip until it snaps over back of sweep. 3. Slide clip until it is touching sweep screw on handle side of door.
PAGE 9
1/2” Self-Drill Pan Painted For a Left Hand Installation, 5/8” go to Page 4. 9 a HANG HINGED STORM DOOR AND REMOVE SPACER CLIPS (Right Hand) 3/4” Machine Flathead I H 1/2” 1/2” J Tools needed: 1” 2” 1 1/2” 7/8” Machine Pan Painted Handle Clip RIGHT HAND HINGED INSTALLS ONLY FOR LEFT HAND HINGED INSTALL, SEE PG.
PAGE 10
1/2” 1/2” 1” SMS Pan Painted 1” Machine Pan Painted 1/2” 10 ! SMS Pan Painted INSTALL 1”I Machine1”Pan Painted H J 1-1/2” 1-1/2” Machine Flathead HANDLE SET (Right Hand) 1” Machine Pan Painted 2” 1-1/2” Machine Flathead x2 #10 b 1-1/2” Machine Flathead 2” a INTERIOR TRIM PLATE 1/2” TRIM PLATE 1 1-1/2” Machine Flathead 2” SMS Pan Painted 2 2” SMS Pan Painted #12 5/8” SMS Pan Painted #12 2 1/2” 1/2” 5/8”LOCK SMS Pan Painted DEAD BOLT KEY CYLINDER BAR LATCH 1.
PAGE 11
1/2” Self-Drill Pan Painted 5/8” 11 INSTALL RAIN CAP EXTENDER AND SCREW COVERS (Right Hand) C 3/4” Machine Flathead L Tools needed: M 1” 2” 1 1/2” 7/8” Machine Pan Painted 1 1/2” Rain Cap Extender (optional) a 1/2” 1/2” b OPTIONAL Screw 1” SMS Covers End Pan Cover 1" 1” SMS Pan Painted OPTIONAL 1/8" c ! ! L 1” Machine Pan Painted C x3 (optional) 1-1/2” Machine Flathead 5/8” #10 L 1-1/2” Machine Flathead 5/8” 1/2” 2” SMS Pan Painted 1.
PAGE 12
INSTALL THE GLASS OR INSECT SCREEN PANEL (Right Hand) i a VIEW i b SNUGGER BAR The glass panel/insect screen is secured in door frame by door handle locking mechanism. Once door handle has been rotated up to vertical position, the glass panel /insect screen are no longer secured in door frame. Immediately remove glass panel/insect screen from door frame after releasing locking mechanism. Failure to do so could result in injury and/or product damage.
PAGE 13
5/8” 14 1/2” TROUBLESHOOTING 5/8” (Right Hand) For additional help with these, 1 1/2” or any other installation steps, please call our Solution Center at 1-800-933-3626. 1/2” Tools needed: 1/2” 1” 2” 1/8” 1 1/2” i a VIEW ! i ! b J B 5/8” 1. Hook the clip on to the sweep 2. Rotate clip until it snaps over back of sweep. 3. Slide clip until it is touching sweep screw on handle side of door.
PAGE 14
CLEANING INSTRUCTIONS WINDOW GLASS – The glass may be cleaned with any household glass cleaner. Keep glass cleaners away from all other components. PLASTIC PARTS – Plastic door components may be cleaned by using a mild soap and water mixture and by gently rubbing the affected area. Do not use harsh abrasives or any product that contains chlorine. ALUMINUM PARTS – Aluminum parts on the door may be cleaned by using a mild soap and water mixture and by gently rubbing the affected area.