Installation Instruction

ManualsBrandsAndrew Wireless System ManualsElectronicsION-M Remote Unit for cellular systems

The Remote Unit, Extension Unit or Master Unit has to be

mounted by proffessionel / special trained installer.

1.1. HIGH POWER RU MECHANICAL INSTALLATIONN

1.1.1. General

Read the health and safety warnings in chapter 1.3.

It is the responsibility of the installer to verify that the supporting surface will safely support the

combined load of the electronic equipment and all attached hardware and components and to ensure that

the unit is safely and securely mounted.

WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING

SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT. The installer must verify that the

supporting surface will safely support the combined load of the electronic equipment and all attached

hardware and components. The screws and dowels (wall anchors) used should also be appropriate for

the structure of the supporting wall.

1. Do not install the unit in a way or at a place where the specifications outlined in the

Environmental and Safety Specifications leaflet of the supplier are not met.

2. It is recommended to use the mounting hardware delivered by the supplier only. If different

mounting hardware is used, the specifications for stationary use of the Remote Unit must not

be exceeded.

 Note: Exceeding the specified load limits may cause the loss of warranty!

3. The unit is considerably heavy. Make sure that a suitable mounting surface is used. Ensure

there is adequate manpower to handle the weight of the system.

4. Due to power dissipation, the Remote Unit may reach a very high temperature. Ensure

sufficient airflow for ventilation.

5. When connecting and mounting the cables (RF, optical, mains, ...) ensure that no water can

penetrate into the unit through these cables.

6. Also observe all additional rules or restrictions regarding mounting that depend on the type of

Remote Unit. For details refer to section 7.2.2 Mechanical Specification. Install the unit

vertically with the fan unit at the top. A maximum tilt angle of 25° from a vertical position

must be kept, as in the following illustrations:

Summary of content (6 pages)

PAGE 1
Installation Instruction The Remote Unit, Extension Unit or Master Unit has to be mounted by proffessionel / special trained installer. 1.1. HIGH POWER RU MECHANICAL INSTALLATIONN 1.1.1. General Read the health and safety warnings in chapter 1.3. It is the responsibility of the installer to verify that the supporting surface will safely support the combined load of the electronic equipment and all attached hardware and components and to ensure that the unit is safely and securely mounted.
PAGE 2
7. A spacing of 40 mm (1.58 inch) around the unit is required. 8. To ensure sufficient airflow when mounting the unit in enclosed spaces, two lid openings (one for the air inlet and the other for the air outlet) have to be provided. Do not block these air inlets and outlets when mounting the Remote Unit. The size of each opening must equal at least 12 x 12 cm (144 cm2). Make sure, too, there is no thermal short circuit between the air inlet and air outlet.
PAGE 3
1.2. ELECTRICAL INSTALLATION 1.2.1. General Read the health and safety warnings in chapter 1.3. 1. This unit contains dangerous voltages. Loss of life, severe personal injury or property damage can be the result if the instructions contained in this manual are not followed. 2. Ground the unit before connecting power supply. A grounding bolt is provided on the cabinet to connect the ground-bonding cable. 3.
PAGE 4
1.3. HEALTH AND SAFETY WARNINGS 1. Danger: Obey all general and regional installation and safety regulations relating to work on high voltage installations, as well as regulations covering correct use of tools and personal protective equipment. 2. Danger: Before opening the unit, disconnect mains power. 3. Danger: Laser radiation! Do not stare into the beam; do not view it directly or with optical instruments. 4. Danger: Due to power dissipation, the remote unit may reach a very high temperature.
PAGE 5
where  P (mW) is the radiated power at the antenna, i.e. the max. rated repeater output power in addition to the antenna gain minus the loss between the repeater and the antenna.  PD (mW/cm²) is the allowed Power Density limit acc. to 47 CFR 1.1310 (B) for general population / uncontrolled exposures which is o F (MHz) / 1500 for frequencies from 300MHz to 1500MHz o 1 for frequencies from 1500MHz to 100.
PAGE 6
Equipment Symbols Used Please observe the meanings of the following symbols used in our equipment and the compliance warnings: Symbol --- Compliance FCC CE Meaning WARNING. This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC Licensee to operate this device. Unauthorized use may result in significant forfeiture penalties, including penalties in excess of $100,000 for each continuing violation.