Installation Manual

ManualsBrandsAndrew Wireless System ManualsElectronicsION-U Remote Unit for cellular systems

Installation Instruction

The Remote Unit, Extension Unit or Master Unit has to be

mounted by proffessionel / special trained installer.

1.1. HIGH POWER RU MECHANICAL INSTALLATIONN

1.1.1. General

Read the health and safety warnings in chapter 1.3.

1. Warning: Do not install the unit in a way or at a place where the specifications outlined in the

Environmental and Safety Specifications leaflet of the supplier are not met.

2. WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING

CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT. Installer must

verify that the supporting surface will safely support the combined load of the electronic

equipment and all attached hardware and components. The supporting wall should be solid

wood or concrete using appropriate screws and dowels (wall anchors).

3. Warning: It is recommended to use the mounting hardware delivered by the manufacturer

only. If different mounting hardware is used, the specifications for stationary use of the

Remote Unit must not be exceeded.

 Note: Exceeding the specified load limits may cause the loss of warranty!

4. Warning: The unit is considerably heavy. Make sure that a suitable mounting surface is used.

Ensure there is adequate manpower to handle the weight of the system.

5. Caution: Due to power dissipation, the Remote Unit may reach a very high temperature.

Ensure sufficient airflow for ventilation.

6. Note: When connecting and mounting the cables (RF, optical, mains, ...) ensure that no water

can penetrate into the unit through these cables.

7. Note: Observe all additional rules or restrictions regarding mounting that apply to specific

Remote Unit types.

8. Note: Observe all additional rules or restrictions regarding mounting that apply to specific

Remote Unit types. For details refer to the mechanical specifications in the data sheet for the

unit. Install the unit vertically with the fan unit at the top. A maximum tilt angle of 25° from a

vertical position must be maintained, as shown in the following illustrations:

Summary of content (7 pages)

PAGE 1
Installation Instruction The Remote Unit, Extension Unit or Master Unit has to be mounted by proffessionel / special trained installer. 1.1. HIGH POWER RU MECHANICAL INSTALLATIONN 1.1.1. General Read the health and safety warnings in chapter 1.3. 1. Warning: Do not install the unit in a way or at a place where the specifications outlined in the Environmental and Safety Specifications leaflet of the supplier are not met. 2.
PAGE 2
9. A spacing of 40 mm (1.66 inch) around the unit is required. 10. To ensure sufficient airflow when mounting the unit in enclosed spaces, two lid openings (one for the air inlet and the other for the air outlet) must be provided. Do not block these air inlets and outlets when mounting the remote unit. The size of each opening must equal at least 12 x 12 cm (144 cm2). Ensure that there is no thermal short circuit between the air inlet and air outlet.
PAGE 3
1.2. ELECTRICAL INSTALLATION 1.2.1. General Read the health and safety warnings in chapter 1.3. 1. Warning: This unit contains dangerous voltages. Loss of life, severe personal injury, or property damage can be the result if the instructions contained in this manual are not followed. 2. Caution: It is compulsory to ground (earth) the unit before connecting the power supply. A grounding bolt is provided on the cabinet to connect the ground-bonding cable. 3.
PAGE 4
12. Caution: The unit complies with the surge requirement according to EN 61000-4-5 (fine protection); however, installation of an additional medium (via local supply connection) and/or coarse protection (external surge protection) is recommended depending on the individual application in order to avoid damage caused by overcurrent. 13. Caution: Observe the labels on the front panels before connecting or disconnecting any cables.
PAGE 5
1.3. HEALTH AND SAFETY WARNINGS 1. Danger: Obey all general and regional installation and safety regulations relating to work on high voltage installations, as well as regulations covering correct use of tools and personal protective equipment. 2. Danger: Laser radiation! Do not stare into the beam; do not view it directly or with optical instruments. 3. Danger: Before opening the unit, disconnect mains power. 4. Danger: Due to power dissipation, the remote unit may reach a very high temperature.
PAGE 6
RF exposure compliance may need to be addressed at the time of licensing, as required by the responsible FCC Bureau(s), including antenna co-location requirements of 1.1307(b)(3). 12. Warning: For installations which have to comply with Europe an EN50385 exposure compliance requirements, the following Power Density limits/guidelines (mW/cm²) according to ICNIRP are valid: o o o 0.
PAGE 7
Equipment Symbols Used Please observe the meanings of the following symbols used in our equipment: Symbol --- Compliance FCC --- --- Meaning WARNING. This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC Licensee to operate this device. Unauthorized use may result in significant forfeiture penalties, including penalties in excess of $100,000 for each continuing violation.