User's Manual

ManualsBrandsAngel ManualsPaintballAngel Fly 2005

Contents

• This Operator’s and User’s Manual is in English.

• It contains important safety guidelines

and Instructions.

• Should you be unsure at any stage, or unable

to understand the contents within this manual

you must seek expert advice.

• Le mode d’emploi est en Anglais.

• Il contient des instructions et mesures

de sécurité importantes.

• En cas de doute, ou s’il vous est impossible

de comprendre le contenu du monde d’emploi,

demandez conseil à un expert.

• Este manual de (operarios y) usarios està

en Inglés.

• Contiene importantes normas de seguridad

e instrucciones.

• Si no esta seguro de algún punto o no entiende

los contenidos de este manual debe conultar

con un experto.

• Diese Bedienungs und Benutzeranleitung

ist in Englisch.

• Sie enthält wichtige herheitsrichtlinien

und -bestimmungen.

• Sollten Sie sich in irgendeiner Weise unsicher

sein, oder den Inhalt dieses Heftes nicht

verstehen, lassen Sie siche bitte von einem

Experten beraten.

General Warnings 2

Switching on your ANGEL 3

Turning off your ANGEL 3

making your ANGEL safe 3

Navigation button 4

Battery replacement 4

Switching ANGEL eyes on/off 5

OPTO board 5

Macro line hose 5

Propellant air/nitrogen supply 6

Adjusting/removing the ASA 6

Installing an air/nitrogen system 6

Bolt removal and rotor breech 7

Velocity adjustment 7

OLED menu 8-9

Modes

Semi Auto 10

NPPL 10

PSP 10

MILLENNIUM 10

XBall/NXL 10

CFOA 10

Full Auto 10

Demo 10-11

Custom Semi 11

Breakout 11

Soft breakout 11

Hard breakout 11

Ramp 11

Parameters

Valve dwell 11

De-Bounce 11-12

Paint type 12

MROF eyes on/off 12

Breakout 12

Ramp 12-13

Shot % filtering 13

Anti bolt stick 13

Software version 13

Factory reset 13

Game timer alarm 14

Tournament lock 14

General care & cleaning 15

Mini reg removal & assembly 16

Rubber finger detent replacement 17

Angel eyes sensor cleaning 17

Eye ribbon removal 18

LPR pressure test 19

LPR adjustment 20

LPR assembly 20

LPR spool removal 20

LPR removal 21

Exhaust valve Stem/guide removal 22

Ram removal 23

trigger adjustment & removal 24

Useful conversions 25

Fault finding 25-26

Warranty - EEC/ROW 27

Warranty - USA/Canada 28

Warranty card inside Back cover

Summary of content (29 pages)

PAGE 1
Contents • This Operator’s and User’s Manual is in English. • I t contains important safety guidelines and Instructions. • S hould you be unsure at any stage, or unable to understand the contents within this manual you must seek expert advice. • L e mode d’emploi est en Anglais. • I l contient des instructions et mesures de sécurité importantes. • En cas de doute, ou s’il vous est impossible de comprendre le contenu du monde d’emploi, demandez conseil à un expert.
PAGE 2
ADHERE STRICTLY TO THESE AND ALL OTHER SAFETY INSTRUCTIONS AND GUIDELINES • The ANGEL is not a toy. • Careless or improper use, including failure to follow instructions and warnings within this Operator Manual and attached to the ANGEL, could cause death or serious injury. • Do not remove or deface any warnings attached to the ANGEL.
PAGE 3
1 Push & hold navigation button for up to 2 secs ADHERE STRICTLY TO THESE AND ALL OTHER SAFETY INSTRUCTIONS AND GUIDELINES NGEL is LIVE and capable of firing. · A Ensure a barrel blocking device is fitted · to the ANGEL. the hopper is removed from · Ensure the ANGEL. that there are no paintballs · Einnsure the ANGEL.
PAGE 4
Navigation Button 1 2 1 T he functions, features and settings ADHERE STRICTLY TO THESE AND ALL OTHER SAFETY INSTRUCTIONS AND GUIDELINES of the ANGEL are controlled by a 3 directional navigation button located on the rear of the grip frame. 2 T he button can move up and down to scroll through features and settings indicated on the display and can be pressed in to select the highlighted function or setting required.
PAGE 5
1 Switching ANGEL eyes on/off 2 ADHERE STRICTLY TO THESE AND ALL OTHER SAFETY INSTRUCTIONS AND GUIDELINES NGEL is LIVE and capable of firing. · A Ensure a barrel blocking device is fitted · to the ANGEL. the hopper is removed from · Ensure the ANGEL. that there are no paintballs · Einnsure the ANGEL.
PAGE 6
Propellant air/nitrogen supply 1 ADHERE STRICTLY TO THESE AND ALL OTHER SAFETY INSTRUCTIONS AND GUIDELINES 2 The ANGEL is designed to operate on Air/ Nitrogen gas. This needs to be supplied to the ANGEL using a suitable first stage regulator. The ideal input pressure is 450 psi, but the ANGEL will operate with an input pressure up to 850 psi. Note: Some preset systems will deliver a higher pressure than their rating.
PAGE 7
ADHERE STRICTLY TO THESE AND ALL OTHER SAFETY INSTRUCTIONS AND GUIDELINES 1 Bolt removal 2 a barrel blocking device is fitted to · EthensureANGEL. nsure the hopper is removed from the · EANGEL. nsure that there are no paintballs in the · EANGEL. the ANGEL is switched off via · Ethensurenavigation button on the rear of the · · · · · · · · grip frame prior to fitting your first stage regulator.
PAGE 8
ADHERE STRICTLY TO THESE AND ALL OTHER SAFETY INSTRUCTIONS AND GUIDELINES OLED menu Status The Status menu allows you to select between Live/Safe, the Information display screen and the Parameters setting. • To access the Status menu press and hold the navigation button up or down for 2 seconds.
PAGE 9
ADHERE STRICTLY TO THESE AND ALL OTHER SAFETY INSTRUCTIONS AND GUIDELINES a barrel blocking device is fitted · Etonsure the ANGEL. the hopper is removed from · Ensure the ANGEL. that there are no paintballs · Einnsure the ANGEL. industry standard eye/face/ear · Pandaintball head protection designed specifically · to stop paintballs and meeting ASTM standard F1776 (USA) or CE standard (Europe) must be worn by user and any person within range.
PAGE 10
MODES • Ensure that the ANGEL is switched on. • Ensure that you are not activating the trigger. • Push and hold the navigation button UP or DOWN for 2 seconds. • The Status menu will be displayed. • Push the navigation button up to highlight the Parameters menu. • Push the navigation button in to select the Parameters menu. • From the Parameters menu, select the Mode feature by pushing the navigation button inward.
PAGE 11
ADHERE STRICTLY TO THESE AND ALL OTHER SAFETY INSTRUCTIONS AND GUIDELINES a barrel blocking device is fitted · Etonsure the ANGEL. the hopper is removed from · Ensure the ANGEL. that there are no paintballs · Einnsure the ANGEL. industry standard eye/face/ear · Pandaintball head protection designed specifically · to stop paintballs and meeting ASTM standard F1776 (USA) or CE standard (Europe) must be worn by user and any person within range.
PAGE 12
Parameters cont... De-Bounce cont... • Push the navigation button up to highlight the Parameters menu. • From the Parameters menu select the De-Bounce feature by pushing the navigation button inwards. • Scroll up or down through the De-Bounce settings by pushing the navigation button up or down. • Once the desired setting is reached press the navigation button inwards to save the new setting. A Saved De-Bounce message will be displayed. The Parameters menu will be displayed.
PAGE 13
ADHERE STRICTLY TO THESE AND ALL OTHER SAFETY INSTRUCTIONS AND GUIDELINES a barrel blocking device is fitted · Etonsure the ANGEL. the hopper is removed from · Ensure the ANGEL. that there are no paintballs · Einnsure the ANGEL. industry standard eye/face/ear · Pandaintball head protection designed specifically · to stop paintballs and meeting ASTM standard F1776 (USA) or CE standard (Europe) must be worn by user and any person within range.
PAGE 14
Game timer/alarm Tournament lock This is a fully interactive game timer with countdown alarm that will allow you and your team to play in unison. The timer and alarm can be set in either 1 second or 1 minute increments from 0 to 60 minutes. Once the alarm and timer are set they will be activated by the first trigger pull after making the ANGEL live and selecting the timer function. • Ensure that the ANGEL is switched on. • Ensure that you are not activating the trigger.
PAGE 15
ADHERE STRICTLY TO THESE AND ALL OTHER SAFETY INSTRUCTIONS AND GUIDELINES General care & cleaning a barrel blocking device is fitted · Etonsure the ANGEL. the hopper is removed from · Ensure the ANGEL. that there are no paintballs · Einnsure the ANGEL. industry standard eye/face/ear · Pandaintball head protection designed specifically · The ANGEL is designed for minimum maintenance and requires far less lubrication and greasing of internal parts than other high performance markers.
PAGE 16
Mini reg removal & assembly 1 ADHERE STRICTLY TO THESE AND ALL OTHER SAFETY INSTRUCTIONS AND GUIDELINES 2 a barrel blocking device is fitted · Etonsure the ANGEL. the hopper is removed from · EthensureANGEL. that there are no paintballs · Einnsure the ANGEL. remove the first stage regulator · Aandlwaysrelease all residual gas pressure from the ANGEL before disassembly.
PAGE 17
ADHERE STRICTLY TO THESE AND ALL OTHER SAFETY INSTRUCTIONS AND GUIDELINES 1 2 a barrel blocking device is fitted · Etonsure the ANGEL. the hopper is removed from · Ensure the ANGEL. that there are no paintballs · Einnsure the ANGEL. industry standard eye/face/ear · Pandaintball head protection designed specifically · to stop paintballs and meeting ASTM standard F1776 (USA) or CE standard (Europe) must be worn by user and any person within range.
PAGE 18
Eye ribbon removal 1 2 1 R emove the eye cover as shown on page 17. 2 R emove the fore grip as shown on page 16. 3 Remove the right hand grip cheek by removing the 3 screws using a suitable 2mm Allen wrench. 4 C arefully unplug the solenoid from the board. 5 C arefully unplug the eye ribbons from the board. 6 R emove the two screws retaining the grip frame using a 2mm Allen wrench and remove the grip frame.
PAGE 19
ADHERE STRICTLY TO THESE AND ALL OTHER SAFETY INSTRUCTIONS AND GUIDELINES 1 LPR pressure test 2 a barrel blocking device is fitted · Etonsure the ANGEL. the hopper is removed from · EthensureANGEL. that there are no paintballs · Einnsure the ANGEL. remove the first stage regulator · Aandlwaysrelease all residual gas pressure from the ANGEL before disassembly. ANGEL can hold a small residual · Tgashe charge, typically two shots, with the · first stage regulator removed.
PAGE 20
LPR Adjustment 1 ADHERE STRICTLY TO THESE AND ALL OTHER SAFETY INSTRUCTIONS AND GUIDELINES 2 a barrel blocking device is fitted · Etonsure the ANGEL. the hopper is removed from · EthensureANGEL. that there are no paintballs · Einnsure the ANGEL. remove the first stage regulator · Aandlwaysrelease all residual gas pressure from the ANGEL before disassembly.
PAGE 21
ADHERE STRICTLY TO THESE AND ALL OTHER SAFETY INSTRUCTIONS AND GUIDELINES 1 2 LPR removal 3 a barrel blocking device is fitted · Etonsure the ANGEL. the hopper is removed from · EthensureANGEL. that there are no paintballs · Einnsure the ANGEL. remove the first stage regulator · Aandlwaysrelease all residual gas pressure from the ANGEL before disassembly. ANGEL can hold a small residual · Tgashe charge, typically two shots, with the · first stage regulator removed.
PAGE 22
Exhaust valve stem removal The magnetic exhaust valve in your ANGEL FLY reduces its working pressure by over 80psi (30%) on the ANGEL A1. The ANGEL FLY’s 200 psi working pressure reduces its kick, making your ANGEL FLY even softer on paint than the ANGEL A1. If you are experiencing gas leaking from the breech area, first ensure your tank is delivering at least 200 psi to your ANGEL.
PAGE 23
ADHERE STRICTLY TO THESE AND ALL OTHER SAFETY INSTRUCTIONS AND GUIDELINES 1 2 3 RAM removal 5 You may need to remove your Ram if the ANGEL’s hammer has come loose or the Ram is leaking. To establish if a gas leak is coming from the Ram, first check your LPR pressure is above 40psi and if so open the breech block and listen for gas emitting from the breech pin slot. If gas is emitting from the breech port, it is not Ram related and will be due to your exhaust valve.
PAGE 24
Trigger adjustment Back stop ADHERE STRICTLY TO THESE AND ALL OTHER SAFETY INSTRUCTIONS AND GUIDELINES Front stop a barrel blocking device is fitted · Etonsure the ANGEL. the hopper is removed from · Ensure the ANGEL. that there are no paintballs · Einnsure the ANGEL. industry standard eye/face/ear · Pandaintball head protection designed specifically The trigger system has four adjustable points: back stop, front stop, magnetic return strength control and activation point.
PAGE 25
USEFUL CONVERSIONS Listed are some useful conversions relating to pressure, velocity, mass and distance. PROBLEM SOLUTION ANGEL WILL NOT FIRE No air or nitrogen present? Propellant Air/Nitrogen Supply. 6 Is the battery operational? Change the battery. 4 Is the ANGEL in ‘SAFE’? Making the ANGEL ‘LIVE’. Is the trigger not closing the button? Trigger Adjustment. 24 1 bar = 14.5038 psi Is the trigger not releasing the button? Trigger Adjustment. 24 1 psi = 0.
PAGE 26
PROBLEM SOLUTION PAGE BREAKING PAINTBALLS Is the paint too fragile? Use less fragile paint. – Is the barrel bore correct for the paint? Use a suitable barrel. – Is the paint swollen, cold or hot? Review your storage of paint. – Are the ANGEL Eyes switched on? Switch ANGEL Eyes on Are the ANGEL Eyes functioning? ANGEL Eyes Test. 5/17 Is the loader battery weak/dead? Replace batteries. – Is a suitable working loader fitted? Check loader specifications.
PAGE 27
Terms of warranty - EEC/R.O.W. (excluding usa/canada). Subject to the conditions set out below WDP warrants that the ANGEL will correspond to its specification at the time of delivery and will be free from defects in materials and workmanship for a period of six months from the date of purchase. WDP gives this warranty subject to the following conditions: • Proof of purchase is required in all warranty claims. • Warranty is not transferable.
PAGE 28
Terms of warranty - USA / Canada 1. General Express Warranties. WDP warrants to the buyer who is purchasing to place into use (Buyer) only, that the ANGEL (Product) shall be free from material manufacturing defects in materials and workmanship for six months from the date of purchase, subject to the requirements, disclaimers and limitations of this Warranty.
PAGE 29