User's Manual
ADHERE STRICTLY TO THESE
AND ALL OTHER SAFETY
INSTRUCTIONS AND GUIDELINES
·
Ensure a barrel blocking device is fitted
to the ANGEL.
·
Ensure the hopper is removed from
the ANGEL.
·
Ensure that there are no paintballs
in the ANGEL.
·
Paintball industry standard eye/face/ear
and head protection designed specifically
to stop paintballs and meeting ASTM
standard F1776 (USA) or CE standard
(Europe) must be worn by user and any
person within range.
·
SHOULD YOU BE UNSURE AT ANY STAGE
YOU MUST SEEK EXPERT ADVICE.
Parameters cont...
Ramp cont...
• Ensure that the ANGEL is switched on.
• Ensure that you are not activating the
trigger.
• Push and hold the navigation button UP
or DOWN for 2 seconds.
• The Status menu will be displayed.
• Push the navigation button up to highlight
the Parameters menu.
• Push the navigation button in to select
the Parameters menu.
• From the Parameters menu select the
Ramp feature by pushing the
navigation button inwards.
• Select Soft or Hard Ramp option using
the navigation button by pressing it
inwards to confirm the desired option.
• You can then select to adjust Start
Delay, Kick in BPS and Drop out
BPS by pressing the navigation button
inwards.
A Saved Start Delay, Kick in BPS and
Drop out BPS message will be displayed.
The Soft or Hard Ramp menu will be
displayed.
Shot % filtering
This allows the adjustment of the point
within the current firing cycle that a new
buffered shot will be accepted.
The Shot % lter is adjustable from
1 to 20 levels.
Level 1 turns the shot filtering off which
allows the additional shot to be registered
at the earliest point after the eyes have
detected a ball and the trigger has provided
a viable re command. Levels 2 through
to 20 sets the % of the ring cycle that
must have been completed before the
additional shot may be allowed from 10%
of the cycle increasing in 5% increments
up to a maximum of 100% of the cycle.
• Ensure that the ANGEL is switched on.
• Ensure that you are not activating the
trigger.
• Push and hold the navigation button
UP or DOWN for 2 seconds.
• The Status menu will be displayed.
• Push the navigation button up to highlight
the Parameters menu.
• Push the navigation button in to select
the Parameters menu.
• From the Parameters menu select the
Shot % Filtering feature by pushing the
navigation button inwards.
• Scroll up or down through the Shot
% Filtering settings by pushing the
navigation button up or down.
• Once the desired setting has been
reached press the navigation button
inwards to save the new setting.
A Saved Shot % Filtering message will
be displayed.
The Parameters menu will be displayed.
Anti Bolt Stick
First shot drop off can occur when the
valve or Ram incurs static friction after a
period of inactivity. This results in the first
shots fired after this inactivity being lower
in velocity because the seals need to break
free from the forces of the static friction.
Anti Bolt Stick programming allows the
dwell time to be increased for the rst 2
shots if the ANGEL has been inactive for 15
seconds to overcome static friction. There
are 20 levels of ABS adjustment ranging
from 0.25 milliseconds to 5 milliseconds.
• Ensure that the ANGEL is switched on.
• Ensure that you are not activating the
trigger.
• Push and hold the navigation button UP
or DOWN for 2 seconds.
• The Status menu will be displayed.
• Push the navigation button up to highlight
the Parameters menu.
• Push the navigation button in to select
the Parameters menu.
• From the Parameters menu select the
Anti Bolt Stick feature by pushing the
navigation button inwards.
• Scroll up or down through the Anti Bolt
Stick settings by pushing the navigation
button up or down.
• Once the desired setting has been
reached, press the navigation button
inwards to save the new setting.
A Saved Anti Bolt Stick message will be
displayed.
The Parameters menu will be displayed.
Software version
The software version is displayed on the
information page.
• With the ANGEL on and Live push the
navigation button up or down for
2 seconds.
• The ANGEL will be in the Status menu.
• Use the navigation button to scroll
through the Status menu settings until
Information is highlighted.
Push the navigation button inwards to
select the Information menu.
Factory reset
The default factory settings can be restored
if required at any time.
• Press the internal button located on
the circuit board inside the grip frame.
• The screen will display the internal
options menu.
• Using the navigation button scroll
up or down to select the reset function.
• Press the navigation button inwards
to initiate the reset function.
• You will be asked to conrm that
you wish to continue with this action.
Press the navigation button inwards
to confirm this is correct.
• A reset message will be displayed on
the screen confirming that the default
settings have successfully been restored.
13
READ ALL WARNINGS BEFORE ATTEMPTING ANY WORK ON YOUR ANGEL. SHOULD YOU BE UNSURE AT ANY STAGE YOU MUST SEEK EXPERT ADVICE.