User's Manual

08
ANGEL iR3
TM
contents
important safety
guidelines
operating instructions
external LCD menus
whilst in SAFE
external LCD C.O.P.S.
menu whilst LIVE
internal tournament
LCD menus
figures
maintenance
fault finding tables
useful conversions
warranties
update info
your ANGEL iR3
TM
operating instructions
FITTING THE HOPPER INTELLIFEED
TM
(OPTIONAL EXTRA)
• Ensure the ANGEL iR3
TM
is switched off via the isolating switch on the rear of the marker
• Ensure a barrel blocking device is fitted to the ANGEL iR3
TM
• Ensure the hopper is removed from the ANGEL iR3
TM
• Ensure that there are no paintballs in the ANGEL iR3
TM
The ANGEL iR3
TM
has the ability to power motorized hoppers with the agitation and electrical supply coming
directly from the ANGEL iR3
TM
. This Intellifeed
TM
system monitors your fire rate and switches on the agitator as
necessary. (See general assembly and wiring diagrams.)
• Remove the existing sight rail using suitable metric Allen key.
• Remove the breech block pull knob by opening the breech, then unscrewing the pull knob while
it is retracted.
• Remove the 2-countersunk Allen screws with suitable metric Allen key from the back plate.
CAUTION: A spring is located under the back plate.
• Remove the left-hand side grip cheek and unplug the battery and 14-way solenoid.
• Remove the grip frame screws and remove the frame.
CAUTION: Care must be shown as the trigger return spring is located under the frame.
• Insert the replacement sight rail and wiring loom, feeding the wire and white plug though the body
to exit at the underside by the other plugs.
• Refit the frame.
CAUTION: Care must be shown to ensure the spring is located correctly.
• Insert all plugs in their relevant sockets.
CAUTION: Care must be shown to ensure wires do not snag on the trigger mechanism.
• Refit grip cheek cover, rear back plate, breech block pull knob and the sight rail.
• The flying lead has a mating plug that fits to the socket on the sight rail, this should be soldered directly
to the hopper motor. All other electronics within the hopper must be removed prior to fitting this lead. Each lead
may be soldered to either of the motor connections.
NOTE: The hopper circuit has over current protection to sense a locked or jammed paddle. Should a jam
occur the hopper drive circuit will shut down until the jam is cleared. Ensure the the hopper motor is free
running and the gear box is fully operational as this can result in slow running speeds.
OPTO BOARD
TM
• Do not attempt to modify the OPTO board
TM
assembly in any way as this will invalidate your warranty
and could lead to safety concerns.
The iR3
TM
incorporates the OPTO board
TM
. This is the latest development in trigger sensing function.
When used in conjunction with the 3Styla
TM
trigger it achieves unsurpassed advancements in trigger
repeatability and sensitivity, its non-mechanical switching results in faster, shorter and lighter trigger strokes
that give the user higher prolonged achievable rates of fire.
NOTES:
• When accessing the Internal Tournament LCD menus the OPTO board
TM
should not be exposed to direct
sunlight or strong external sources of light without the grip cheek fitted as this light will induce a safety
feature, that will prevent the Angel iR3
TM
from firing whilst it remains exposed to the strong external light.
• The correct function of the OPTO board
TM
can be verified by the LCD display whilst the Angel iR3
TM
is at rest in safe mode the display will display “SAFE”.
• With trigger pulled and held the display will show the firing mode eg “SEMI”.
• The OPTO board
TM
is a non-mechanical switch that is silent in its operation and no audible “click” is present.
ADHERE STRICTLY TO THESE AND ALL OTHER SAFETY
INSTRUCTIONS AND GUIDELINES
ADHERE STRICTLY TO THESE AND ALL OTHER SAFETY
INSTRUCTIONS AND GUIDELINES