User guide

ManualsBrandsAngelcare ManualsProducts for childrenAC401 Deluxe

OWNER’S MANUAL

MOVEMENT & SOUND BABY MONITOR

Model AC401

FOR YOUR PEACE OF MIND

Movement Alarm

Your monitor comes with the movement alarm activated.

When switching on your monitor it will alarm, with or without

the Sensor Pad plugged in, if no movement is detected.

Deactivate the movement function to use the monitor without

the Sensor Pad.

Batteries

Insert the enclosed rechargeable batteries into the Parent

Unit. If inserted incorrectly the Parent Unit will not charge

when placed in the charging cradle. The battery icon will flash

briefly on the Parent Unit screen to indicate charging.

Cord Safety

Ensure the Nursery Unit is at least 1 metre away from your

baby’s cot. The Sensor Pad cord must always be kept out of

reach of baby and secured using the cord cover kit provided.

Voice-activated Sound Transmission

Your monitor will transmit when it detects sound from

your baby or in their room. You can adjust the microphone

sensitivity to suit your needs.

DON’T

FORGET

IMPORTANT ADVICE FOR INITIAL SETUP

PLEASE FOLLOW THE INSTRUCTIONS CAREFULLY FOR CORRECT SETUP

Please DO NOT return this product to the store. For assistance please

contact our helpline on 0845 009 1789 or email helpline@babyhelpline.co.uk

Mon – Fri 10am – 4pm, excluding bank holidays.

Summary of content (17 pages)

PAGE 1
for your peace of mind OWNER’S MANUAL MOVEMENT & SOUND BABY MONITOR Model AC401 IMPORTANT ADVICE FOR INITIAL SETUP DON ’T FORG ET Movement Alarm Your monitor comes with the movement alarm activated. When switching on your monitor it will alarm, with or without the Sensor Pad plugged in, if no movement is detected. Deactivate the movement function to use the monitor without the Sensor Pad. Batteries Insert the enclosed rechargeable batteries into the Parent Unit.
PAGE 2
TABLE OF CONTENT Warning Warnings.......................................................................................3 AC401 SETUP REQUIREMENTS.........................................................7 1. THIS PRODUC T CANNOT REPL ACE RESPONSIBLE ADULT SUPERVISION. This product is designed to aid in the monitoring of your child. When using the monitor, you must still provide the supervision necessary for the continued safety of your child.
PAGE 3
non-rechargeable batteries. Rechargeable batteries are ONLY to be charged under adult supervision. Keep all batteries away from children. 15. Important Safety Instructions 15.1 Read these instructions - All the safety instructions should be read before the product is operated. 15.2 Keep these instructions. The safety and operating instructions should be retained for future reference. 15.3 Heed all warnings – All warnings on the product and in the operating instructions should be adhered to. 15.
PAGE 4
16.10 DO NOT attempt to rejuvenate the batteries provided with or identified for use with this product by heating them. Sudden release of battery electrolyte may occur, causing burns or irritation to eyes or skin. 16.11 If and when necessary, the batteries must be replaced with identical new ones or equivalent (volts and size). If a battery to be replaced is connected with other batteries in series, replace the other batteries at the same time as well. DO NOT mix old and new batteries. 16.
PAGE 5
STEP 1 - ChargING THE parent unit 1 Important Never use regular alkaline batteries in the Parent Unit; they may explode. 2 3 HOW TO CHARGE THE BATTERIES IN THE PARENT UNIT: Leave the Parent Unit in the Charging Cradle to fully charge the unit. Although the batteries at 1/2 capacity works normally, we recommend that you fully recharge them. 1) Remove the battery door and insert the Rechargeable Batteries (included).
PAGE 6
STEP 2 - InstallING THE sensor pad 2.2 Select the crib leg you will be using to secure the cord covers Recommended 6 5 3 4 2 Use the crib leg by the wall closest to the Nursery Unit (Fig 1). In cases where the Nursery Unit is across the room, use the leg closest to the Nursery Unit to position the covered wire (Fig 2). It is always preferable that the covered cord run along a wall.
PAGE 7
STEP 3 - SetTING up THE Nursery Unit 6 8 cm 1 6 1) Remove the battery door and insert 4 AAA Alkaline Batteries (not included). 6) Place the 6 cord cover approximately 8 cm from the edge of the mattress support. th 2) Place the Nursery Unit at a minimum of 1 m away from the crib. 7) Snap together the remaining cord covers that will run along the floor. 7 8) Remove any cord slack to make sure no parts of the cord are loose.
PAGE 8
STEP 4 - TURNING ON your Monitor 1 Important Icons SOUND TRANSMISSION (VOX) 2 1) Press the Parent Unit ON/OFF button for 2 seconds. 2) Slide ON the Nursery Unit Power ON/OFF button. Note: The screen of the Parent Unit will show the channel of transmission (C1 to C8) and after 5 seconds the room temperature and function icons. The connecting process should be done within 30 seconds. If longer, the operation will be ignored and you will have to start over.
PAGE 9
STEP 5 - Testing and Getting to know your Monitor 5.3 - CHANGING THE MOVEMENT AND SOUND MONITORING FUNCTIONS TO SET DETECTION MODE: The Angelcare® monitor can be used with the pre-program factory settings or you can also customise your settings to your preference. All changes and adjustments made in the main menu and sub-menu will not be activated unless you confirm them by pressing the Select button.
PAGE 10
To activate this function: To stop the alarm 1) Press Menu button 2 times. OR Place your hand back on the mattress. Shut the Nursery Unit OFF OR Press any key to put on Hold (see section 5.8) The Out-of-Range Indicator will blinks. ON 2) Using the arrows, turn the function ON or OFF. 1 OFF 2 3) Press Select button to confirm your choice. Out-of-Range Alarm • • • To adjust SENSOR PAD sensitivity level: Alarm activates when your two units are not communicating.
PAGE 11
TO ADJUST SOUND SENSITIVITY (VOX): 5.7 - ALARM SETTINGS The sensitivity of the microphone is adjustable and has 4 levels (the most sensitive is level 4). This means that sound will only transmit based on the level that you set. Allows you to select your preferred alarm mode. 1) Press Menu button 4 times. 1) Press Menu button 3 times. The Nursery Unit Indicator will blinks. Sensitivity Level icon will appear.
PAGE 12
YOU ARE NOW READY TO USE YOUR MONITOR 5.9 - TEMPERATURE TO Activate temperature alarm: 1) Press Menu button 5 times. The Temperature Indicator (Low and High) will appear. The Angelcare® monitor can be used with the pre-program factory settings or you can also customise your settings to your preference. 2) Using the arrows, to turn the function ON or OFF. 1 3) Press Select button to confirm your choice.
PAGE 13
STEP 6 - ACTIVATING AND DEACTIVATING ADDITIONAL functions TROUBLESHOOTING The Angelcare® monitor can be used with the pre-program factory settings or you can also customise your settings to your preference. TAKING CARE OF YOUR RECHARGEABLE BATTERIES In order to activate any changes made in the main menu and sub-menu it must be confirmed by pressing the Select button.
PAGE 14
ALARM WILL NOT SOUND • Avoid contact with the crib when the monitor is ON. • Place crib near a solid supporting wall to avoid Sensor Pad from detecting movement from outside the crib. • You may need to decrease the sensitivity, refer to step 5.3. NO SOUND IS BEING TRANSMITTED • • • • • • Bring Parent Unit closer to Nursery Unit. Check/replace batteries or recharge Parent Unit. Check connections or change to another electrical outlet. Ensure both units are ON. Ensure mains supply units are activated.
PAGE 15
Technical specifications Range: Open field : up to 250 m They may only be replaced by 4 or 8 AAA NIMH rechargable batteries. Number of Channels: USA/Canada: 8 channels. Europe: 8 channels. Batteries: Power Supply: 4 AAA alkaline batteries (not included) or 100-240V AC/7.5V DC adapter for Nursery Unit. 4 or 8 AAA rechargeable batteries and 100-240V AC/7.5V DC adapter for Charging Base for the Parent Unit. Caution: To reduce the risk of electric shock, do not expose this product to rain or moisture.
PAGE 16
30 31
PAGE 17
This Angelcare Baby Monitor is a Personal Care Product. Please DO NOT return this to the store, but contact us initially for advice and assistance: Angelcare Helpline on 0845 009 1789 Website: www.angelcare.co.uk Email: helpline@babyhelpline.co.uk NOTE: Helpline is open Monday to Friday, 10am to 4pm, excluding bank holidays.