circo 19"″ led ring light CI-LR20 INSTRUCTIONS
Introduction Congratulations on purchasing the Angler Circo 19" LED ring light. The Angler Circo CI-LR20 is a compact, lightweight, and portable way to light your subject. It provides 360 degrees of even illumination, ideal for enhancing facial features. It’s a great fit for fashion and beauty photography and when used in combination with its diffuser sock, which provides softer lighting.
To prolong the life of the unit, turn the power off and unplug the light when it is not in use. Do not attempt to disassemble or repair this product. There are components inside that can produce a hazardous electric shock. Keep this product away from water and any flammable gases or liquids. Do not leave the device in a closed vehicle under the sun or in other areas subject to very high temperatures. Make sure this product is powered off when plugging it into a power source.
LED Array Front Back Dimming knob DC input Also included: Carrying case User manual 4 Power switch Phillips-head screws
Diffuser Sock Touch-fastener straps Elastic band 1/4"-20 Camera set screw AC Power Supply AC power cord DC barrel connector Flexible Stand Adapter Locking knob Height adjustment thumb screws Camera Bracket 5/8" receiver 5
Attaching the Diffuser Sock It is recommended that the diffuser sock is placed on the LED array before adding any other accessories. 1. Lay the LED array faceup on a flat, clean surface. 2. Look for the elastic band on the bottom of the sock, and wrap it around the base of the array. Fit the sock over the ring light so that the dark fabric band is on the inside of the ring. Stretch the elastic edge of the sock over the outside of the ring. Secure the sock with the attached touch-fastener straps.
Attaching the Camera Bracket The adjustable camera bracket attaches your camera to the ring light for tripod-mounted shooting. It connects to the bottom of the LED array via two Phillips-head screws. 1. Use a Phillips screwdriver (not included) to remove the screws from the bottom of the LED array. Do not remove the larger screw in the middle—only the two on the ends. 2. Position the camera bracket behind the LED array, and align the screw holes on the bracket with the ones on the array. 3.
5. If necessary, use the two thumbscrews on the back of the camera bracket to adjust the bracket’s height. 5 6. For tripod-mounted shooting, use the socket in the 1/4"-20 set screw to mount the assembly to your tripod. Make sure the assembly is securely mounted to the tripod.
Attaching the Flexible Stand Adapter The flexible stand adapter incorporates a gooseneck and 5/8" receiver to mount the ring light on a light stand for easy off-camera positioning. Like the camera bracket, it connects to the bottom of the LED array via two Phillips-head screws. 1. Use a Phillips screwdriver (not included) to remove the screws from the bottom of the LED array. Do not remove the larger screw in the middle—only the two on the ends. 2.
Powering and Dimming the LED The power supply is rated for multivoltage use at a range of 100–240 V and 50/60 Hz. Before connecting, make sure the array’s power switch is set to Off. Connect the AC cord to the AC input on the DC barrel connector. Plug the DC barrel connector into the LED array’s DC input, and then plug the power cord into an AC power socket. Plug adapters (not included) may be required in some countries. The LED is turned on or off via the power switch.
SPECIFICATIONS number of LED count's 640 Color temperature 5500 K CRI 95 Dimming range 0%–100% Camera weight rating 2 lb. (0.9 kg) AC power supply 100–240 V AC at 50/60 Hz; conversion to DC 14.8–15 V, 1.5 A Dimensions (H × W × D): 23" × 19" × 1.75" (58.4 × 48.3 × 4.4 cm) Diameter 19" (48.26 cm) Weight 2.85 lb. (1.
One-Year Limited Warranty This Angler product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later.