Instructions / Assembly

ManualsBrandsAnimal House ManualsChicken CoopsLarge 74 in. Modular Chicken Coop Poultry and Hen House with Solid Top Shaded Run/Yard

The CHICK-INN™ ASSEMBLY INSTRUCTIONS

#5403670

47in H x 27.25in W x 74in D

119,4 x 70 x 188cm

03-5403670 rev. 2018-07-10 PG.1

Please read through instructions completely prior to assembly.

TOOLS NEEDED: Phillips Screwdriver or power drill with phillips head bit

ASSEMBLY: Recommend 2 people. Approximate assembly time with 2 people: 90 Minutes

SITE PREPARATION: Ensure the area where you are placing your coop is a ﬂat level

surface, free from debris that can harm your pet.

SEPARATE AND INDENTIFY ALL PARTS

on page 2

“EGGcelerator”

Model #5403670

Summary of content (6 pages)

PAGE 1
The CHICK-INN™ ASSEMBLY INSTRUCTIONS 47in H x 27.25in W x 74in D 119,4 x 70 x 188cm #5403670 Please read through instructions completely prior to assembly. TOOLS NEEDED: Phillips Screwdriver or power drill with phillips head bit ASSEMBLY: Recommend 2 people. Approximate assembly time with 2 people: 90 Minutes SITE PREPARATION: Ensure the area where you are placing your coop is a flat level surface, free from debris that can harm your pet.
PAGE 2
Hen House A=1 B=1 Hen House Front Hen House Back w/Door w/Air Vents C=1 Hen House Left Side Lower Run D=1 Hen House Right Side E=1 Entry/Exit Ramp F=1 Lower Run Front Piece Nest Box I=1 Left Side P=1 Main Run Gap Filler J=1 Back K=1 Right Side S=2 Hen House Roof Pieces X=4 Y=2 Anti-rot/Anti-dig Anti-rot/Anti-dig Ground Edging Ground Edging Long pieces Short pieces CAUTION! - SHARP EDGES! G=1 Lower Run Back Piece H=1 Lower Run End Piece Main Run L=1 Floor T=1 Nest Box Locking Lid P1 = 9 +
PAGE 3
STEP 1 - ATTACH GROUND EDGING (X, Y) First determine the top/bottom and inside/outside of pieces (F, G, H, N, O, Q) F - has 2 holes on the OUTSIDE right and left sides, 1 hole on top G - has 2 holes on the OUTSIDE right and left sides, 2 holes on top H - has 2 holes on the right and left edges, 2 holes on bottom OUTSIDE INSIDE N - has 3 holes on the OUTSIDE right edge, 3 holes on the OUTSIDE left side, 2 holes on top TOP Q - from the OUTSIDE, the gate will be on the right F O - Top is slanted Attach
PAGE 4
STEP 2 - ASSEMBLE LOWER RUN (F,G,H,D) Attach F and H use (2) P2 screws. NOTE: F attaches to the OUTSIDE edge of H Attach G to OUTSIDE edge of H, use (2) P2 screws Attach D to the INSIDE of F & G, use (4) P2 screws P2 x 2 P2 x 4 P2 x 2 STEP 3 - ASSEMBLE & ATTACH HEN HOUSE TO LOWER RUN (A, B, C) Attach A to D use (2) P2 screws. NOTE: A attaches to the OUTSIDE of D.
PAGE 5
ADD DIVIDER (M) Slide in TRAY V W M Add 2 ROOSTS (W) on the inside of the house, there are 2 notches V STEP 5 - ATTACH MAIN RUN FRONT PIECE WITH GATE (Q) Use (3) P1 Screws Install sliding door HANDLE (P6). NOTE: slide handle through the hole in piece (Q) before attaching the brackets. Use Four P5 screws.
PAGE 6
STEP 7 - ATTACH ASPHALT ROOF PIECES & CAP (S, T, U) Attach NEST BOX LOCKING LID (T) Use (6) P5 screws Attach (2) HEN HOUSE ROOF PIECES (S) Use (8) P3 screws NOTE: The unfinished, slant cut edges are positioned at the peak. Push pieces towards the back until they stop, this will align the holes in the roof with the holes in the coop. Attach HEN HOUSE PEAK CAP (U) Use (4) P4 screws T S S U P3 x 8 P5 x 6 P4 x 4 03-5403670 rev. 2018-07-10 PG.6 ©2018 Jewett-Cameron Company • 800-955-2879 • www.