Installation Manual

ManualsBrandsAnnovi Reverberi ManualsOutdoor Power ToolsAnnovi Reverberi AR620 Ar North America Commerical Pressure Washer, Black

This product is under warranty to the original retail consumer against

defects in material and workmanship for a period of 1 (one) year and is a

complete “bumper to bumper” warranty including the spray gun, the high

pressure hose and all accessories from the date of purchase. The warranty

is not transferable or assignable. This warranty covers replacement parts.

This limited one year warranty applies only to products used in consumer

applications and is void in rental or any commercial application. Reason-

able care must be used in conformity with operation and maintenance

instructions in the owner’s manual. Failure to follow these instructions will

void this warranty. This warranty gives you speci c legal rights and you

may also have other rights which vary from state to state.

Keep your original receipt of purchase in case of warranty claim. Any pow-

er washer or parts returned for a warranty claim must have a “RETURNED

MERCHANDISE AUTHORIZATION (RMA) NUMBER.” You must obtain an RMA

NUMBER by calling A.R. North America, Inc. at 1-866-235-5112 Monday

through Friday, 8 a.m. to 5 p.m. (CST) or e-mail info@arblueclean.com. Any

return without an RMA NUMBER will be considered unauthorized and will

be shipped back at the expense of the sender. Freight costs to the compa-

ny for warranty work must be paid by the purchaser.

A.R. North America, Inc.

Attn: Power Washer Warranty Department

140 – 81st Avenue NE, Fridley, MN 55432

Phone: 1-866-235-5112

Fax: 1-866-331-2762

Email: info@arblueclean.com

Website: www.arblueclean.com

PRESSURE WASHER LIMITED WARRANTY

WARRANTY RETURNS

Questions, problems, missing parts?

Before returning to your retailer, call our

customer service department at 1-866-235-5112,

8 a.m. - 5:00 p.m., CST, Monday - Friday.

www.arblueclean.com

AR620 & AR630

Electric Pressure Washer

ASSEMBLY, CARE AND USE

INSTRUCTIONS

READ CAREFULLY

IMPORTANT: RETAIN THESE

INSTRUCTIONS AND ATTACH RECEIPT

TO MANUAL FOR FUTURE REFERENCE.

Important Notice

Winter storage or long time storage. Drain all water out of

the pump. Flush the pressure washer with a 50% antifreeze

solution, and relieve the pressure. Flush the pressure washer

before you use it again to remove the antifreeze.

AR620/630_FN

Summary of content (10 pages)

PAGE 1
PRESSURE WASHER LIMITED WARRANTY This product is under warranty to the original retail consumer against defects in material and workmanship for a period of 1 (one) year and is a complete “bumper to bumper” warranty including the spray gun, the high pressure hose and all accessories from the date of purchase. The warranty is not transferable or assignable. This warranty covers replacement parts.
PAGE 2
SAFETY INSTRUCTIONS NOTES Read and understand these instructions as they pertain with safety. Pay special attention to the safety symbol throughout this manual. Failure to comply with these instructions may result in personal injury or property damage. DO NOT allow children to operate or play on or around this equipment. BEFORE OPERATING 1. Plug the unit into a 3-prong outlet that is properly grounded. Improper grounding can result in electrical shock. 2.
PAGE 3
NOTES WHILE OPERATING 16. Always use water that is clear and free from particles 17. Always point the wand nozzle away from people and animals, the high pressure the unit generates is very dangerous. 18. Keep the pressure hose connected to the machine and wand while unit is pressurized. 19. Never leave the wand unattended while the machine is running. 20. Always seek emergency medical immediately if any fluid penetrates the skin. The cut may be deeper and more serious than it appears. 21.
PAGE 4
Pos ASSEMBLY INSTRUCTION PRE-ASSEMBLY CHECKLIST 1. The pressure washer should be as close as possible to the water supply. 2. Locate the pressure washer on a solid, level surface with a gentle slope to prevent water from building up in the work area. Excess water can make surfaces slippery. 3. Position the unit so the operator has easy access to the pressure washer and its controls. 4.
PAGE 5
AR630TSS / AR630TSS-HOT ASSEMBLY INSTRUCTION (CONT) UNLOADER ASSEMBLING 1. 48 40 Tighten all connections and replace worn parts before starting the machine. Sudden release of high pressure streams may result if connections detach during use. This can cause serious injury. Never disconnect any part of the unit while the machine is running or before relieving system pressure, it is dangerous. Seek medical attention if an injury ever occurs.
PAGE 6
Pos OPERATING INSTRUCTIONS (CONT) STARTING THE PRESSURE WASHER 1. Turn on the water supply to the proper gpm flow rate. 2. Plug power cord into properly grounded outlet. 3. Turn nozzle to low pressure and squeeze trigger. 4. Turn “ON/OFF” switch to the “ON” position and wait until a constant stream of water comes out. Adjust nozzle sleeves to achieve proper pressure and coverage area. DURING OPERATION 1. Observe all safety instructions through this manual. 2.
PAGE 7
AR620 / AR630 / AR630-HOT OPERATING INSTRUCTIONS (CONT) UNLOADER 5. Spray the backside of the nozzle with a lubricant and work the nozzle back and forth from high pressure to low pressure. This will help keep the nozzle from sticking. 6. Follow this procedure each time the machine is stopped. Having the nozzle set at low pressure and squeezing the trigger on the gun when you start the unit will reduce the startup load of the unit.
PAGE 8
Pos MAINTENANCE (CONT) CLEANING TIPS The gun nozzle supplied with the pressure washer provides optimum cleaning for universal cleaning applications if used properly. Cleaning agents are most effective when the surface is rinsed first to loosen dirt. After pre-rinsing to loosen dirt, then clean with detergent. Detergent should be applied from the bottom to the top of the washing area. Apply detergent and allow the detergent to react with the dirt, then rinse from the top to the bottom.
PAGE 9
AR620 / AR630 / AR630-HOT / AR630TSS / AR630TSS-HOT SETTING NOZZLE PRESSURE / CHEMICAL INJECTOR High Pressure 1. For high pressure pull back on nozzle. Make sure to keep all parts of hand away from out coming water. 3 4 Diagram A 5 2 54 55 52 56 Low Pressure 69 2 68 53 67 2. 57 63 1 For low pressure and chemical suction push the nozzle forward. Keep all parts of hand away from out coming water. 66 64 65 Diagram B 61 62 58 70 59 60 Fan Spray 23 22 7 3.
PAGE 10
USING THE SOAP INJECTOR Your pressure washer is supplied with a downstream low pressure soap/ chemical injector. Soap is added after the water flows through the pump. The injector is used add liquids to the water. The injector works only on low pressure. The draw soap/chemical into the pressure washer, insert the filter end of the pick-up hose into the soap/chemical. Adjust the nozzle to the low pressure position.