User Manual
Table Of Contents
- Intr
- 1.Product features overv
- 1.1Product introduction
- 1.2 Product parameters.
- 1.3Functional features
- 2.Operating instructions
- 2.1The front panel expla
- 2.2Rear Panel Interface
- 2.3The mouse operation i
- 2.4Input method instruct
- 2.5The remote control ope
- 2.6Interface specificatio
- 2.6.1Interface elements s
- 2.6.2Commonly used butto
- 2.7Menu description
- 3.Installation and conne
- 3.1Installation Notes
- 3.2Prepare before instal
- 3.3The camera placed in the
- 4.System function introdu
- 4.1Starting up/Login/Log
- 4.1.1 Starting up
- 4.1.2 Login
- 4.1.3 Logout
- 4.1.4 Restart
- 4.1.5 Close the screen o
- 4.1.6 Turn off
- 4.2Boot wizard
- 4.3 Video management
- 4.3.1 Search device
- 4.3.2 Add device
- 4.3.3 Advanced setup
- 4.3.4.Delete device
- 4.3.5Repeater function
- 4.3.6Edit channel
- 4.3.7Encoding setup
- 4.3.8Code stream value
- 4.3.9 Channels in detail
- 4.3.10 Channel OSD
- 4.3.11 Camera
- 4.4 Network Setup
- 4.4.1.Network Setup
- 4.4.2.Dynamic DNS
- 4.4.3.FTP26
- 4.4.4.E-Mail
- 4.4.5.PPPoE
- 4.4.6.3G
- 4.4.7.Wireless setup
- 4.5 PTZ setup
- 4.5.1 PTZ parameter setu
- 4.5.2 PTZ control operat
- 4.5.3 PTZ automatic crui
- 4.6 Video
- 4.6.1 Manual video
- 4.6.2 Timing video
- 4.6.3 The motion detecti
- 4.6.4 Alarm video
- 4.7 Video playback
- 4.7.1 Quick playback
- 4.7.2 Regular playback
- 4.8Video backup
- 4.9 Alarm
- 4.9.1Motion detecting al
- 4.9.2Video loss alarm
- 4.10 General setup
- 4.10.1General setup
- 4.10.2Timeset
- 4.10.3Screen setup
- 4.10.4Hard disk setup
- 4.11Device maintenance a
- 4.11.1 System information
- 4.11.2 User management
- 4.11.3 Restore the factor
- 4.11.4 System maintenanc
- 4.11.5 Software upgrade
- 4.11.6 IPC maintenance
- 5WEB access
- 5.1 Introduction
- 5.2 LAN Access
- 5.2.1 Login
- 5.2.2 Preview
- 5.2.3 Playback
- 5.2.4 Configuration
- 5.3 E-seenet access
- 5.3.1 E-seenet ID login
- 5.3.2 The user name logi
- 6.Mobile terminal access
- 7. Appendix
- 7.1Hard disk capacity un
- 7.2Video required capaci
- Introduction
- 1.Product features overview
- 2.Operation explanation
- 3.Installation and connection
- 4.System function introduction
- 4.1Starting up / login / logout / restart / close
- 4.2Boot wizard
- 4.3 Video management
- 4.3.1 Search for device
- 4.3.2 Add device
- 1. Code matching instructions：
- 2:Code matching methods：
- 4.3.3 Advanced setups
- 4.3.4.Delete device
- 4.3.5 Repeater setup
- 4.3.6.Edit Channel
- 4.3.7.Encoding setup
- 4.3.8 Stream value
- 4.3.9 Channel details
- 2、Click Refresh, you can search the camera in curr
- 4.3.10 Channel OSD
- 3, Select the display setup, enter the location of
- 4.3.11 Camera
- 4.4 Network setup
- Click Reset to restore the information of the wire
- 4.5 PTZ setup
- 4.6 Recording
- 4.7 Video playback
- 4.8 Video backup
- 4.9 Alarm
- 4.10 General Setups
- 4.11 Equipment maintenance and management
- 5WEB Access
- 6.Mobile access
- 7.Appendix
Wireless NVR Kit Manual
12
When power supply is abnormal, it will cause the hard disk video recorder can not work, or even damage the
NVR, it is recommended to use the stable power supply for power supply.
Explanation
Before starting up, make sure that the display or monitor is connected to the video output of the device.
Specific starting up steps are as follows:
1，Plug in the power, the front panel power indicator
is red.
2，Turn on the rear panel power switch or tap the front panel power "On" key. The device starts
to start, as shown in the following figure:
4.1.2 Login
When the system is powered on and started, after waiting for the system to initialize, the system will automatically
pop up the login interface. As shown below. The user needs to complete the login before proceeding.
Steps：
1，Using the left mouse button click the user name edit box, and enter the local login user name, the default factory
settings for the user name is admin.
2，Using the left mouse button click the password edit box, and enter the local login password, the default factory
settings password is empty, that mean do not need filled out.
3，Using the left mouse button to click "OK" to complete the login.
Explanation