Antaira Technologies - Industrial Ethernet Switches LNX-1202G-10G-SFP User Manual V1.1 LNX-1202G-10G-SFP 12-Port Industrial Gigabit Unmanaged Ethernet Switch with 10*10/100/1000Tx + 2*10G SFP+ Slots Version 1.
Antaira Technologies - Industrial Ethernet Switches LNX-1202G-10G-SFP User Manual V1.1 © Copyright 2018 Antaira Technologies, LLC. All Rights Reserved This document contains information, which is protected by copyright. Reproduction, adaptation or translation without prior permission is prohibited, except as allowed under the copyright laws. Trademark Information Antaira is a registered trademark of Antaira Technologies, LLC, Microsoft Windows and the Windows logo are the trademarks of Microsoft Corp.
Antaira Technologies - Industrial Ethernet Switches LNX-1202G-10G-SFP User Manual V1.1 FCC Notice This equipment has been tested and found to comply with the limits for a Class-A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy.
Antaira Technologies - Industrial Ethernet Switches LNX-1202G-10G-SFP User Manual V1.1 Table of Contents 1.Overview ....................................................................... 1 1.1 Key Features ...................................................... 1 1.2 Package Contents .............................................. 2 1.3 Safety Precaution ............................................... 2 2.Hardware Description .................................................. 3 2.1 Physical Dimensions .....
Antaira Technologies - Industrial Ethernet Switches LNX-1202G-10G-SFP User Manual V1.1 1. Overview Antaira Technologies’ LNX-1202G-10G-SFP is a 12-port industrial grade gigabit Ethernet unmanaged switch. This rugged switch is enclosed in a metal IP30 rated design with a full gigabit high port count which allows for a more versatile implementation. The LNX-1202G-10GSFP series is equipped with 10*10/100/1000 Ethernet ports and 2*100/1000 SFP+ slots.
Antaira Technologies - Industrial Ethernet Switches LNX-1202G-10G-SFP User Manual V1.1 1.2 Package Contents 1 – Quick installation guide 1 – LNX-1202G-10G-SFP 1 – Set of wall mounting brackets and screws 1 – DC cable – 18 AWG & DC jack 5.5 x 2.1mm 1.3 Safety Precaution Attention: If the DC voltage is supplied by an external circuit, please use a protection device on the power supply input.
Antaira Technologies - Industrial Ethernet Switches LNX-1202G-10G-SFP User Manual V1.1 2. Hardware Description 2.1 Physical Dimensions Figure 2.1, below, shows the physical dimensions of Antaira Technologies’ LNX-1202G-10G-SFP series: 12-port industrial gigabit unmanaged Ethernet switch with 10*10/100/1000Tx RJ45 + 2*100/1000Fx SFP+ slots. (W x D x H) is 54mm x 99mm x 142mm Figure 2.
Antaira Technologies - Industrial Ethernet Switches LNX-1202G-10G-SFP User Manual V1.1 2.2 Front Panel The front panel of the LNX-1202G-10G-SFP: 12-port industrial gigabit unmanaged Ethernet switch with 10*10/100/1000Tx RJ45 and 2*100/1000 SFP+ slots. See Figure 2.2.
Antaira Technologies - Industrial Ethernet Switches LNX-1202G-10G-SFP User Manual V1.1 2.4 LED Indicators There are LED light indicators located on the front panel of the industrial Ethernet switch that display the power status and network status. Each LED indicator has a different color and has its own specific meaning, see below in Table 2.1.
Antaira Technologies - Industrial Ethernet Switches LNX-1202G-10G-SFP User Manual V1.1 The following figures show the cabling schematics for straight-through and crossover cables. Figure 2.4 Straight-Through Cables Schematic Figure 2.5 Crossover Cables Schematic The following figures show the 10,100, and 1000 Ethernet RJ‐45 pin outs. Figure 2.6 RJ45 Ethernet Port Pin Outs 2.6 Cabling Twisted-pair segments can be connected with an Unshielded Twisted Pair (UTP) or Shielded Twisted Pair (STP) cable.
Antaira Technologies - Industrial Ethernet Switches LNX-1202G-10G-SFP User Manual V1.1 To connect the transceiver and LC cable, please follow the steps below: First, insert the SFP transceiver module into the SFP slot as shown below in Figure 2.7. Notice that the triangle mark is at the bottom of the SFP slot. Figure 2.8 shows the SFP transceiver module was inserted. Figure 2.7 - Transceiver to the SFP Module Figure 2.
Antaira Technologies - Industrial Ethernet Switches LNX-1202G-10G-SFP User Manual V1.1 2.7 Wiring the Power Inputs Please follow the below steps to insert the power wire. 1. Insert the positive and negative wires into the PWR1 (V1+, V1-) and PWR2 (V2+, V2-) contacts on the terminal block connector as shown below in Figure 2.12. Figure 2.12 - Power Terminal Block 2. Tighten the wire-clamp screws to prevent the wires from loosening, as shown below in Figure 2.13. Figure 2.
Antaira Technologies - Industrial Ethernet Switches LNX-1202G-10G-SFP User Manual V1.1 3. Mounting Installation 3.1 DIN-Rail Mounting The DIN-Rail is pre-installed on the industrial Ethernet switch from the factory. If the DIN-Rail is not on the industrial Ethernet switch, please refer to Figure 3.1 to learn how to install the DIN-Rail on the switch. Figure 3.1 The Rear Side of the Switch and DIN-Rail Bracket Follow the steps below to learn how to hang the industrial Ethernet switch. 1.
Antaira Technologies - Industrial Ethernet Switches LNX-1202G-10G-SFP User Manual V1.1 3.2 Wall Mounting Follow the steps below to mount the industrial Ethernet switch using the wall mounting bracket as shown below in Figure 3.4. 1. Remove the DIN-Rail bracket from the industrial Ethernet switch by loosening the screws. 2. Place the wall mounting brackets on the top and bottom of the industrial Ethernet switch. 3.
Antaira Technologies - Industrial Ethernet Switches LNX-1202G-10G-SFP User Manual V1.1 4. Hardware Installation 4.1 Installation Steps This section will explain how to install Antaira Technologies’ LNX-1202G-10G-SFP: 12-port industrial gigabit unmanaged Ethernet switch with 10*10/100/1000Tx and 2*100/1000 SFP+ slots. Installation Steps 1. Unpack the industrial Ethernet switch from the original packing box. 2. Check if the DIN-Rail bracket is screwed on the industrial Ethernet switch.
Antaira Technologies - Industrial Ethernet Switches LNX-1202G-10G-SFP User Manual V1.1 5. Network Applications Figure 5.
Antaira Technologies - Industrial Ethernet Switches LNX-1202G-10G-SFP User Manual V1.1 6. Trouble Shooting Always verify the right power cord or adapter is being used. Never use a power supply or adapter with a non-compliant DC output voltage or it will burn the equipment. Select the proper UTP or STP cable in order to construct the network. Use an Unshielded Twisted-Pair (UTP) or Shield Twisted-Pair (STP) cable for RJ45 connections: 100Ω Category 5e for 10/100/1000Mbps.
Antaira Technologies - Industrial Ethernet Switches LNX-1202G-10G-SFP User Manual V1.1 7. Technical Specifications Table 7.1 has the technical specifications for Antaira Technologies’ LNX-1202G-10G-SFP: 12port industrial gigabit unmanaged Ethernet switch with 10*10/100/1000Tx and 2*100/1000 SFP+ slots. Standards IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-Tx Fast Ethernet IEEE 802.3ab 1000Base-T IEEE 802.
Antaira Technologies - Industrial Ethernet Switches LNX-1202G-10G-SFP User Manual V1.1 Approvals IEC61000-4-2 (ESD), IEC61000-4-3 (RS), IEC61000-4-4 (EFT), EMS IEC61000-4-5 (Surge), IEC61000-4-6 (CS), IEC-61000-4-8 (Magnetic Field) IEC60068-2-32 (Free fall) Stability Testing IEC60068-2-27 (Shock) IEC60068-2-6 (Vibration) Green RoHS Compliant Safety Certificate FCC, CE Warranty 5 Years Table 7.
