Antaira Technologies - Industrial Ethernet Switches LNX-1604G-SFP Series User Manual V1.1 LNX-1604G-SFP Series 16-Port Industrial Gigabit Unmanaged Ethernet Switches with 12*10/100/1000Tx + 4*100/1000 SFP Slots Version 1.
Antaira Technologies - Industrial Ethernet Switches LNX-1604G-SFP Series User Manual V1.1 © Copyright 2018 Antaira Technologies, LLC. All Rights Reserved This document contains information, which is protected by copyright. Reproduction, adaptation or translation without prior permission is prohibited, except as allowed under the copyright laws. Trademark Information Antaira is a registered trademark of Antaira Technologies, LLC, Microsoft Windows and the Windows logo are the trademarks of Microsoft Corp.
Antaira Technologies - Industrial Ethernet Switches LNX-1604G-SFP Series User Manual V1.1 FCC Notice This equipment has been tested and found to comply with the limits for a Class-A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy.
Antaira Technologies - Industrial Ethernet Switches LNX-1604G-SFP Series User Manual V1.1 Table of Contents 1.Overview ....................................................................... 1 1.1 Key Features ...................................................... 1 1.2 Package Contents .............................................. 2 1.3 Safety Precaution ............................................... 2 2. Hardware Description ................................................. 3 2.1 Physical Dimensions ..
Antaira Technologies - Industrial Ethernet Switches LNX-1604G-SFP Series User Manual V1.1 1. Overview Antaira Technologies’ LNX-1604G-SFP series is a 16-port industrial grade gigabit Ethernet unmanaged switch. This rugged switch is enclosed in a metal IP30 rated design with a full gigabit high port count which allows for a more versatile implementation. The LNX-1604G-SFP series is equipped with 12*10/100/1000 RJ45 Ethernet ports and 4*100/1000 dual rate SFP slots.
Antaira Technologies - Industrial Ethernet Switches LNX-1604G-SFP Series User Manual V1.1 1.2 Package Contents 1 - LNX-1604G-SFP (-T): 16-port industrial gigabit unmanaged Ethernet switch with 12*10/100/1000Tx + 4*100/1000 SFP slots 2 - Wall mounting brackets and screws 1 - DC cable –18 AWG & DC jack 5.5x2.1mm 1.3 Safety Precaution Attention: If the DC voltage is supplied by an external circuit, please use a protection device on the power supply input.
Antaira Technologies - Industrial Ethernet Switches LNX-1604G-SFP Series User Manual V1.1 2. Hardware Description 2.1 Physical Dimensions Figure 2.1, below, shows the physical dimensions of Antaira Technologies’ LNX-1604G-SFP series: 16-port industrial gigabit unmanaged Ethernet switch with 12*10/100/1000Tx RJ45 + 4*100/1000Fx SFP slots. (W x D x H) is 59mm x 99mm x 142mm Figure 2.
Antaira Technologies - Industrial Ethernet Switches LNX-1604G-SFP Series User Manual V1.1 2.2 Front Panel The front panel of the LNX-1604G-SFP series: 16-port Industrial Gigabit unmanaged Ethernet switch with 12*10/100/1000Tx, and 4*100/1000 SFP Slot. See Figure 2.2.
Antaira Technologies - Industrial Ethernet Switches LNX-1604G-SFP Series User Manual V1.1 2.4 LED Indicators There are LED light indicators located on the front panel of the industrial Ethernet switch that display the power status and network status. Each LED indicator has a different color and has its own specific meaning, see below in Table 2.1.
Antaira Technologies - Industrial Ethernet Switches LNX-1604G-SFP Series User Manual V1.1 2.5 Ethernet Ports RJ-45 Ports (Auto MDI/MDIX): The RJ-45 ports are auto-sensing for 10/100/1000Base-Tx devices connections. Auto MDI/MDIX means that the switch can connect to another switch or workstation without changing the straightthrough or crossover cabling. See the figures shown below for straight-through and crossover cabling schematics. RJ-45 Pin Assignments (Table 2.
Antaira Technologies - Industrial Ethernet Switches LNX-1604G-SFP Series User Manual V1.1 The following figures show the cabling schematics for straight-through and crossover cables. Figure 2.4 Straight-Through Cables Schematic Figure 2.5 Crossover Cables Schematic The following figures show the 10,100, and 1000 Ethernet RJ‐45 pin outs. Figure 2.6 RJ45 Ethernet Port Pin Outs 2.
Antaira Technologies - Industrial Ethernet Switches LNX-1604G-SFP Series User Manual V1.1 The small form-factor pluggable (SFP) is a compact optical transceiver used in optical communications for both telecommunication and data communication applications. To connect the transceiver and LC cable, please follow the steps below: First, insert the SFP transceiver module into the SFP slot as shown below in Figure 2.7. Notice that the triangle mark is at the bottom of the SFP slot. Figure 2.
Antaira Technologies - Industrial Ethernet Switches LNX-1604G-SFP Series User Manual V1.1 2.7 Wiring the Power Inputs Please follow the below steps to insert the power wire. 1. Insert the positive and negative wires into the PWR1 (V1+, V1-) and PWR2 (V2+, V2-) contacts on the terminal block connector as shown below in Figure 2.12. Figure 2.12 - Power Terminal Block 2. Tighten the wire-clamp screws to prevent the wires from loosening, as shown below in Figure 2.13. Figure 2.
Antaira Technologies - Industrial Ethernet Switches LNX-1604G-SFP Series User Manual V1.1 3. Mounting Installation 3.1 DIN-Rail Mounting The DIN-Rail is pre-installed on the industrial Ethernet switch from the factory. If the DIN-Rail is not on the industrial Ethernet switch, please refer to Figure 3.1 to learn how to install the DIN-Rail on the switch. Figure 3.1 The Rear Side of the Switch and DIN-Rail Bracket Follow the steps below to learn how to hang the industrial Ethernet switch. 1.
Antaira Technologies - Industrial Ethernet Switches LNX-1604G-SFP Series User Manual V1.1 3.2 Wall Mounting Follow the steps below to mount the industrial Ethernet switch using the wall mounting bracket as shown below in Figure 3.4. 1. Remove the DIN-Rail bracket from the industrial Ethernet switch by loosening the screws. 2. Place the wall mounting brackets on the top and bottom of the industrial Ethernet switch. 3.
Antaira Technologies - Industrial Ethernet Switches LNX-1604G-SFP Series User Manual V1.1 4. Hardware Installation 4.1 Installation Steps This section will explain how to install Antaira Technologies’ LNX-1604G-SFP (T): 16-port industrial gigabit unmanaged Ethernet switch with 12*10/100/1000Tx ports, and 4*100/1000 SFP slots. Installation Steps 1. Unpack the industrial Ethernet switch from the original packing box. 2. Check if the DIN-Rail bracket is screwed on the industrial Ethernet switch.
Antaira Technologies - Industrial Ethernet Switches LNX-1604G-SFP Series User Manual V1.1 5. Network Applications Figure 5.
Antaira Technologies - Industrial Ethernet Switches LNX-1604G-SFP Series User Manual V1.1 6. Trouble Shooting Always verify the right power cord or adapter is being used. Never use a power supply or adapter with a non-compliant DC output voltage or it will burn the equipment. Select the proper UTP or STP cable in order to construct the network. Use an unshielded twisted-pair (UTP) or shield twisted-pair (STP) cable for RJ-45 connections: 100Ω Category 5e for 10/100/1000Mbps.
Antaira Technologies - Industrial Ethernet Switches LNX-1604G-SFP Series User Manual V1.1 7. Technical Specifications Table 7.1 has the technical specifications for Antaira Technologies’ LNX-1604G-SFP series: 16port industrial gigabit unmanaged Ethernet switch with 12*10/100/1000Tx, and 4*100/1000 SFP slots. Standards IEEE 802.3 10Base-T 10Mbit/s Ethernet IEEE 802.3u 100Base-Tx, 100Base-Fx, Fast Ethernet IEEE 802.3ab 1000Base-Tx Gigabit Ethernet IEEE 802.
Antaira Technologies - Industrial Ethernet Switches LNX-1604G-SFP Series User Manual V1.