LNX-800AG 8-Port Industrial Gigabit Unmanaged Ethernet Switches - w/8*10/100/1000Tx User Manual
FCC Warning This equipment has been tested and found to comply with the limits for a Class-A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. It may cause harmful interference to radio communications if the equipment is not installed and used in accordance with the instructions.
Table of Contents Introduction ................................................................ 1 Features ................................................................... 1 Package Contents .................................................... 2 Hardware Description ............................................... 3 Physical Dimension .................................................. 3 Front Panel .............................................................. 4 Top View ..................................
Introduction Antaira’s LNX-800AG is a smart 8-Port Industrial Gigabit Unmanaged Ethernet Switch supporting 8-Port 10/100/1000Tx that can automatically sense transmission speeds of 10/100/1000 Mbps. The RJ-45 interface can also be auto-detected, so MDI or MDI-X is automatically selected and a crossover cable is not required. All Ethernet ports have memory buffers that support the store-and-forward mechanism. This assures that data is properly transmitted.
Case/Installation IP-30 Protection Installation in Pollution Degree 2 Environment DIN Rail and Wall Mount Design Provides EFT Protection 3,000 VDC for Power Line Supports 6,000 VDC Ethernet ESD Protection Package Contents Please refer to the package contents list below.
Hardware Description The Industrial switch’s hardware spec, port, cabling information, and wiring installation will be described below.
Front Panel The front panel of the Industrial switch is shown below: Front Panel of the Industrial Switch Top View The top view of the Industrial switch has one terminal block connector of two DC power inputs and relay circuit contact.
LED Indicators The diagnostic LEDs located on the front panel of the Industrial switch provide real-time information of the system and optional status. The following table provides the description of the LED status.
All ports on this Industrial switch support an automatic MDI/MDI-X operation, and users can use straight-through cables (see figure below) for all network connections to PCs or servers, or to other switches or hubs. With straight-through cable, pins 1, 2, 3, and 6, at one end of the cable, are connected straight through to pins 1, 2, 3 and 6 at the other end of the cable. The table below shows the 10BASE-T/100BASE-TX/1000BASE-TX MDI and MDI-X port pin outs.
The following figure shows the 10/100/1000 Ethernet RJ-45 pin outs. Cabling Use unshielded twisted-pair (UTP) or shielded twisted-pair (STP) cable for RJ-45 connections: 100Ω Category 3, 4 or 5 cable for 10Mbps connections, 100Ω Category 5 cable for 100Mbps, or 100Ω Category 5e/above cable for 1000Mbps connections. The cable between the switch and the link partner (switch, hub, workstation, etc.) must be less than 100 meters (328 ft.) long.
2. Tighten the wire-clamp screws to prevent the wires from loosening. Note The wire gauge for the terminal block should be in the range between 12~ 24 AWG. If only using one power source, jumper Pin 1 to Pin 5 and Pin 2 to Pin 6 to eliminate power fault alarm. Wiring the Fault Alarm Contact The fault alarm contact is in the middle of the terminal block connector as the picture shows below.
Mounting Installation DIN-Rail Mounting The DIN-Rail is screwed on the Industrial switch from the factory. If the DIN-Rail is not screwed on the Industrial switch, please see the following pictures to screw the DIN-Rail on the switch. Follow the steps below to hang the Industrial switch. 1. Use the screws to screw the DIN-Rail bracket on the rear side of the Industrial switch. 2. To remove the DIN-Rail bracket, reverse the step 1.
3. After the DIN-Rail bracket is screwed on the rear side of the switch, insert the top of DIN-Rail on to the track. 4. Then, lightly pull down the bracket on to the rail. 5. Check if the bracket is mounted tight on the rail. 6. To remove the Industrial switch from the rail, reverse steps above.
Wall Mounting Follow the steps below to mount the Industrial switch using the wall mount bracket. 1. Remove the DIN-Rail bracket from the Industrial switch; loosen the screws to remove the DIN-Rail. 2. Place the wall mount bracket on the top and bottom of the Industrial switch. 3. Use the screws to screw the wall mount bracket on the Industrial switch. 4. Use the hook holes at the corners of the wall mount bracket to hang the Industrial switch on the wall. 5.
Hardware Installation This section is to explain how to install the LNX-500AG – 5-Port Industrial Gigabit Unmanaged Ethernet Switch. Installation Steps 1. Unpack the Industrial switch packing. 2. Check if the DIN-Rail bracket is screwed on the Industrial switch. If the DIN-Rail is not screwed on the Industrial switch, please refer to the DIN-Rail Mounting section for DIN-Rail installation.
Network Application This segment provides an example of an Industrial switch application.
Troubleshooting Verify the right power cord/adapter, never use power supply/adapter with noncompliant DC output voltage, or it will burn the equipment. Select the proper UTP/STP cable to construct the network with using the right cable. Use unshielded twisted-pair (UTP) or shield twisted-pair (STP) cable for RJ-45 connections: 100Ω Category 5e/above cable for 10M/100Mbps. Also be sure that the length of any twisted-pair connection does not exceed 100 meters (328 feet).
Technical Specification The LNX-800AG - 8-Port Industrial Gigabit Unmanaged Ethernet Switch technical specifications are shown below. IEEE 802.3 10Base-T Ethernet Standard IEEE 802.3u 100Base-TX Fast Ethernet IEEE 802.3ab 1000Base-Tx Gigabit Ethernet IEEE802.
Installation Operating Temp. DIN Rail Mounting, Wall Mounting Standard Operating Temperature: -10oC to 70oC Extend Operating Temperature: -40oC to 75oC Operating Humidity 5% to 95% (Non-Condensing) Storage Temperature -40oC to 85oC Case Dimension IP-30, 30mm (W) x 95mm (D) x 140mm (H) FCC Class A EMI CE EN61000-4-2/3/4/5/6/8 CE EN61000-6-2 CE EN61000-6-4 Safety UL/cUL Class 1 Div.
