Installation Manual

P1 P2 Fault
3
4
1
2
7
8
5
6
Practical Operation
Q I G
Quick Installation Guide
LNP-800AGH-T
LNP-800AGH-T
Version 1.2
Quick Installation Guide
Features
The LNP-800AGH-T is unmanaged PoE Ethernet switch with P.S.E. Function. The
LNP-800AGH-T supports Power over Ethernet, a system to transmit electrical
power, along with data, to remote devices over standard twisted-pair cable in an
Ethernet network. The LNP-800AGH-T switch has 8X10/100/1000Base-T(X) P.S.E
(Power Sourcing Equipment) ports. P.S.E. is a device (switch or hub for instance)
that will provide power in a PoE setup. The wide operating temperature range from
o o
-40 C to 70 C can satisfy most operating environments. Therefore, the switch is one
of the most reliable choices for PoE Ethernet application.
Introduction
Specifications
Switch Model
Physical Ports
Technology
Ethernet Standards
LED Indicators
Green: Power LED x2Power indicator
10/100/1000Base-T(X) P.S. E.
Port in RJ45 Auto MDI/MDIX
LNP-800AGH-T
8
IEEE 802.3 for 10Base-T,
IEEE 802.3u for 100Base-TX
IEEE 802.3ab for 1000Base-T
IEEE 802.3x for Flow con trol
IEEE 802.3at PoE specification (up to 30 Watts per port for P.S.E.)
MAC Table
2048 MAC addresses
Environmental
o o
-40 to 85 C (-40 to 185 F)Storage Temperature
Operating Temperature
5% to 95% Non-condensingOperating H umidity
Regulatory approvals
FCC Part 15, CISPR (EN55022) class AEMI
EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge),
EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
EMS
IEC60068-2-27Shock
IEC60068-2-32
IEC60068-2-6Vibration
Free Fal l
Warranty
5 years
o o
-40 to 70 C (-40 to 158 F)
Amber: Indicate PWR1 or PWR2 failure
Fault i ndicator
Fault contact
Relay
Relay output to carry capacity of 1A at 24 VDC
Power
Redundant Input power
Power consumption(Typ.)
8 Watts (Power de vice not in cluded)
Overload current protection
Reverse polarity protection
Present
Not Present
Physical Characteristic
Enclosure
IP-30
Dimension (W x D x H)
Weight (g)
390 g
26.1(W)x94.9(D)x144.3(H) mm (1.03x3.74x5.68inch.)
10/100/1000Base-T( X)
port indicator
RJ45
Green for port Link/Act.
Green for PoE power injected.
The LNP-800AGH-T can be used in connecting several PoE P.D. Ethernet devices like
IP-Cameras or other Ethernet devices. In addition, there are two different power
inputs at terminal block to avoid interruption caused by power down. When the
primary DC power input fails, the backup power input will take over immediately to
guarantee a non-stop operation.
Industrial Unmanaged Gigabit PoE Switch
PRINTED ON RECYCLED PAPER
EN60950-1, UL Class 1 Division 2Safety
GI GAB IT
I N D U S T R I A L
SW IT C H
Provide 8x10/100/1000Base-T(X) PoE (P.S.E.) ports
Support P.S.E. based on IEEE 802.3at standard up to 30 Watts per port
Support auto-negotiation and auto-MDI/MDI-X
Support store and forward transmission
Support flow control
Rigid IP-30 housing design
DIN-Rail and wall mounting enabled
Power Connection Guide
Frame Ground
PWR- 1PWR- 2
V2- V2 + V1- V1 +
G
1A@24V DC 50-57V
Power
Supply
50-57 VDC
V+
V-
Warning
Device
GND+24V
V+
V-
DIP Switch Select for
Power Alarm Relay Output
Power
Supply
50-57 VDC
Power
Supply
DIP-2
OFF
OFF
ON
DIP-1
Power failure relay alarm disabled
PWR-1 failure, alarm enabledrelay
PWR-2 failure, alarm enabledrelay
DIP Switch Function
OFF
ON
OFF
Description
DIP-Switch
Power-1 failed warning : (ON) enable, (OFF) disableDIP-Switc h 1
Power-2 failed warning : (ON) enable, (OFF) disable
DIP-Switc h 2
Front Panel
Power LED
Power Fault LED
A
Gigabit LAN Port
Green: PoE power injected
Green: Link/Act
Po E
ON
PWR-1 or PWR-2 failure,
relay alarm enabled
ON
Dual DC input 48-57VDC on 6-pin terminal block