User manual

ManualsBrandsAntari ManualsFog MachineOnboard DMX

User Manual

Antari Z Series Fog Machine

Congratulations on the purchase of your new

ANTARI Z Series FOG MACHINE.

Introduction

Thank you for choosing an ANTARI Fog Machine. You now own a rugged and powerful tate-of-the-art

machine. Prior to use, we suggest that you carefully read all of the instructions. By following the

suggestions found in this user manual, you can look forward to the reliable and satisfactory performance of

your ANTARI Fog Machine for years to come.

Please follow these operation, safety and maintenance instructions to ensure a long

and safe life for your fog machine.

Cautions

Risk of electric shock. Disconnect the appliance from the electric supply before

removing the cover. Note: there are no user serviceable parts inside.

Danger of electric shock

♦ Keep this device dry.

♦ For inside use only. Not designed for outside use.

♦ For the 110V models, use 3-prong grounded electrical outlet only. Prior to use take care

to determine that the unit is installed at the rated voltage.

♦ Always unplug your ANTARI Fog Machine before filling its tank.

♦ Keep fog machine upright.

♦ Turn off or unplug when not in use.

♦ This machine is not water- or splash-proof. If moisture, water, or fog liquid gets inside the

housing, immediately unplug the unit and contact a service technician or your ANTARI

dealer before using it again.

♦ No user serviceable parts inside. Refer to your ANTARI dealer or other qualified service

personnel.

Danger of burns

♦ For adult use only. Fog machine must be installed out of the reach of children. Never

leave the unit running unattended.

♦ Never aim the output nozzle directly at people.

Summary of content (6 pages)

PAGE 1
User Manual Antari Z Series Fog Machine Congratulations on the purchase of your new ANTARI Z Series FOG MACHINE. Introduction Thank you for choosing an ANTARI Fog Machine. You now own a rugged and powerful tate-of-the-art machine. Prior to use, we suggest that you carefully read all of the instructions. By following the suggestions found in this user manual, you can look forward to the reliable and satisfactory performance of your ANTARI Fog Machine for years to come.
PAGE 2
♦ Fog machine output is very hot. Avoid coming within 60 cm of the output nozzle during operation. ♦ Locate the fog machine in a well-ventilated area. Never cover the unit’s vents. In order to guarantee adequate ventilation, allow a free air space of at least 20 cm around the sides and top of the unit. ♦ Never aim the output nozzle at open flames. ♦ If the supply cord is damaged, it must be replaced by manufacturer or its service agent or similarly qualified person in order to avoid a hazard.
PAGE 3
Operation ♦ Plug power cord into a grounded electrical outlet. If necessary, turn power switch on rear of unit to “ON” position. Warm-up is complete when green lamp lights up on remote unit. ♦ To emit fog, press the appropriate button on the remote for the desired length of time. ♦ The remote unit’s lamp will cycle on and off as the machine re-heats to the proper operating temperature. ♦ For further information on operating your ANTARI Fog Machine, see the section titled, “Remote Control Operation”.
PAGE 4
1. Via the Function key, you can adjust the desired settings. After pressing the Function key once, the display shows "Interval Set". Adjust the interval between each fog emission (within the range of 1 to 255 seconds) by means of the Up-/Down keys. By pressing the Function-key twice, the display shows "Duration Set". Adjust the duration of each fog emission (within the range of 1 to 20 seconds) by means of the Up/Down keys.
PAGE 5
Cleaning your fog machine regularly will help reduce costly parts replacement and repair charges. Maintenance Do not allow the fog liquid to become contaminated. Always replace the caps on the fog liquid container and the fog machine liquid tank immediately after filling. After every 40 hours of continuous operation, it is recommended to run a cleaning solution composed of 80% distilled water/20% white vinegar through the system to prevent the accumulation of particulate matter in the heating element.
PAGE 6
DMX Setting for Z-series fog machines with onboard DMX Channel A 250-255 6 - 249 0–5 0 - 5 = OFF 6 – 249 = Volume Control ( 5% - 95%) 250 – 255 = Maximum Volume Output ( 100%) The Z-1200, Z-1500 and Z-3000 fog machines all have onboard DMX control. Currently all three models use 1 channel to control volume output operation. Each channel has a value range of 0 to 225.