W-515 & W-530 Fog Machine User Manual Please read and save these instructions. Antari Lighting and Effects Ltd.
User Manual W-515 & W-530 Fog Machine Congratulations on the purchase of your new ANTARI W-Series FOG MACHINE. Introduction Thank you for choosing an ANTARI W-Series Fog Machine. You now own a rugged and powerful state-of-the-art machine. Prior to use, we suggest that you carefully read all of the instructions. By following the suggestions found in this user manual, you can look forward to the reliable and satisfactory performance of your ANTARI Fog Machine for years to come.
children. Never leave the unit running unattended. Never aim the output nozzle directly at people. Fog machine output is very hot. Avoid coming within 50 cm of the output nozzle during operation. Locate the fog machine in a well-ventilated area. Never cover the unit's vents. In order to guarantee adequate ventilation, allow a free air space of at least 20 cm around the sides and top of the unit. Never aim the output nozzle at open flames.
Before beginning your initial setup on ANTARI W-515 & W-530 Fog Machine, make sure that there is no evident damage caused by transportation. In the event that the unit's housing or cable is damaged, do not plug it in and do not attempt to use it until after contacting your ANTARI dealer for assistance. Setup Remove all packing materials from shipping box. Check that all foam and plastic padding is removed, especially in the nozzle area. Place fog machine on a flat surface and remove fog liquid tank cap.
output volume of Timer mode (the range is between 1% and 100%) by UP / DOWN buttons. User can trigger Timer mode when LCD shows “Ready To Fog” and press Timer button and when machine is working under Timer mode, pressing Timer button again can end Timer mode. Note: There is a Non-Stop Burst function between Timer Out 1% and Timer Out 100%. Choosing this function can make machine generate continuous fog output under Timer mode. 4.
- When the wireless function is on, LCD displays " Ready To Fog W” (W means Wireless) - When the fluid sensor is on, LCD displays “Ready To Fog S” ( W means Sensor ) - When the above two features both are on, LCD displays “Ready To Fog WS” - When the above two features both are off, LCD displays “Ready To Fog” Instructions of Radio Wireless Remote * Transmitter: - Use DC 12V battery - Working Distance: 50 meters in open area (Wireless distance may vary depending on the interference) - All transmitters are
3. The included transmitter has been registered before shipment. User can use it directly without any setting. The initial setting is pressing button A can trigger the machine and pressing button B can stop it. 4. If user wants to use other transmitters (except the included one) to control machine, the setting must be completed within 15 seconds after switching on machine.15 seconds after switching on machine, it will leave “transmitter setting mode” automatically.
Note * If you experience low output, pump noise or no output at all, unplug immediately. Check fluid level, the external fuse, and power from the wall. If all of the above appears to be O.K., plug the unit again. If fog does not come out after pressing the remote button for 30 seconds, check the hose attached to the tank to make sure there is fluid going through the hose. If you are unable to determine the cause of the problem, do not continue pressing the remote, as this may damage the unit.
W-530 External View 07 02 05 04 01-Nozzle 02-Handle 03 03-Body 04-Tank & tank’s cap 05-PU tube & filter 01 06-Tube adaptor 07-Safety ring 08-Control outlet socket (3 Pin XLR for DMX) 09 09-Control inlet socker (3 Pin XLR for DMX) 06 17 08 10-Control outlet socket (5 Pin XLR for DMX) 11 11-Control inlet socket WIRELESS RECEIVER DMX 10 (5 Pin XLR for DMX) 12-Rocker switch / Power OUT IN 16 WARNING! ATTENTION! • AVANT LE REMPLACEMENT DU FUSIBLE DÉBRANCHER L'APPAREIL.
Performance Note All fog machines develop condensation around the output nozzle. Because this may result in some moisture accumulation on the surface below the output nozzle, consider this condensation when installing your unit. All fog machines may sputter small amounts of fog occasionally during operation and for a minute or so after being turned off. All fog machines have a recycling period after long bursts when the machine will shut itself down for a short period in order to heat up again.
Warranty Warranty shall be valid only if the product is purchased from Antari's authorized distributors or dealers. For warranty service, send the product only to an authorized distributor or dealer. All warranties are void if the product has been modified in any manner; if the product has been repaired or serviced by unauthorized personnel; or the product is damaged due to improper use or maintenance as set forth in the instruction manual.
For current product information visit Antari at : www.antari.com , www.antari.com.tw For information requests please contact us at : sales@antari.
