WiFi-800 Fog Machine User Manual English • Français • Deutsch • 中文 © 2014 Antari Lighting and Effects Ltd.
This is world’s 1st SmartPhone controlled fog machine:Antari WiFi800 .
User Manual Congratulations on the purchase of your new ANTARI WiFi-800 FOG MACHINE. Introduction Thank you for choosing the ANTARI WiFi-800 Fog Machine. You now own a state-of-the-art machine. Prior to use, we suggest that you carefully read all of the instructions. By following the suggestions found in this user manual, you can look forward to the reliable and satisfactory performance of your ANTARI Fog Machine for years to come.
Danger of Burns This device is for adult use only and must be installed out of the reach of children. Never leave the unit running unattended. Never aim the output nozzle directly at people. Fog machine output is very hot. Avoid coming within 60 cm of the output nozzle during operation. Locate the fog machine in a well-ventilated area. Never cover the unit’s vents. In order to guarantee adequate ventilation, allow a free air space of at least 20 cm around the sides and top of the unit.
1. One unit of Antari WiFi-800 Fog Machine 2. Power cord 3. User Manual If any equipment is missing contact your ANTARI dealer immediately. Before beginning your initial setup on ANTARI WiFi-800 Fog Machine, make sure that there is no evident damage caused by transportation. In the event that the unit’s housing or cable is damaged, do not plug it in and do not attempt to use it until after contacting your ANTARI dealer for assistance.
Connecting mobile devices with iOS / Android to WiFi-800 Step 1: On your mobile devices, select Settings > Wi-Fi > list of available Wi-Fi device will be shown. Step 2: Select WIFI800-0000XXXX (e.g. WIFI800-00001001). “0000XXXX” is based on the last four digits of the serial number, which is printed on the rear of the machine (near the power cord). It is also the default SSID and password. Step 3: A password query is displayed.
Controlling The Fog 800 application provides you two ways to control your WiFi-800 fog machine: Timer Mode – allows you to set the fog duration time. Slide the time bar (from 1 to 60 seconds); press ON to start emitting fog. The fog emission will stop once the timer counts down to zero. Continuous Mode – simply press the ON button to emit fog. The machine continuously emits fog; to stop press the OFF button.
Advanced Wi-Fi settings Wi-Fi settings are intended for users with advanced knowledge only. A web-based configuration panel allows you to customize your Wi-Fi settings. To start the configuration, first establish a Wi-Fi connection with the machine, then open a web browser, enter http://192.168.16.254 and when the login window appears enter the default user name admin and password admin. The configuration panel is displayed.
Wireless settings > Basic Network Mode Select one of the following that meets your clients 11b/g mixed mode 11b only 11g only Network Name(SSID) Broadcast Network Name(SSID) AP Isolation Frequency (Channel) 11b/g/n mixed mode default 11n only(2.4G) The name of your wireless network, create a name for your wireless network using up to 32 characters. Enable is default setting. If Disable is selected, the SSID of the machine will not be seen.
Wireless Settings > Security Select a SSID to start configuration Choose one of the following mode for data protection: Disable OPENWEP SSID choice Security Mode WPA-PSK WPA2-PSK WPA Algorithms Pass Phrase Key Renewal interval WPAPSKWPA2PSK (default) TKIP AES TKIPAES Setup password Enter the amount of time before the group key used for broadcast and multicast data is changed (3600 is default) Administration > Management Account Password Change login account name (default is admin) Change login p
Technical Specifications Model Power Supply WiFi-800 AC100-120V, AC 220-240V / 50HZ - 60HZ 800 W Power Consumption Output Volume 3000 Cubic Feet / Min Tank Capacity 0.8 Liter 60 Min. / 0.8 Liter Fluid Consumption 4.1 kg Weight Dimensions (LxWxH) 315 x 128 x 220 mm Optional Controllers Z-10 On/Off Controller, Z-40 Timer Controller, Z-50 Wireless Controller 1.7 min First Heat-up Time Optional Controllers for WiFi-800 Z-10: 10 meter wired remote controller with 1/4 inch jack plug.
Z-10, Z-40, Z-50 Remote Controllers Performance Note All fog machines develop condensation around the output nozzle. Because this may result in some moisture accumulation on the surface below the output nozzle, consider this condensation when installing your unit. All fog machines may sputter small amounts of fog occasionally during operation and for a minute or so after being turned off. Maintenance Do not allow the fog liquid to become contaminated.
Note: Cleaning your fog machine regularly can help reduce replacement and repair costs. After a certain period time of usage, all fog machines tend to clog due to the thick consistency of fog liquid and the high temperature at which it vaporizes. However, a properly maintained fog machine should provide a longer and more reliable life-time. Storage 1. When the machine is not in use, store it in a cool and dry place. 2.
User Manual Congratulations on the purchase of your new ANTARI WiFi-800 FOG MACHINE. Introduction Thank you for choosing the ANTARI WiFi-800 Fog Machine. You now own a state-of-the-art machine. Prior to use, we suggest that you carefully read all of the instructions. By following the suggestions found in this user manual, you can look forward to the reliable and satisfactory performance of your ANTARI Fog Machine for years to come.
Danger of Burns This device is for adult use only and must be installed out of the reach of children. Never leave the unit running unattended. Never aim the output nozzle directly at people. Fog machine output is very hot. Avoid coming within 60 cm of the output nozzle during operation. Locate the fog machine in a well-ventilated area. Never cover the unit’s vents. In order to guarantee adequate ventilation, allow a free air space of at least 20 cm around the sides and top of the unit.
4. One unit of Antari WiFi-800 Fog Machine 5. Power cord 3. User Manual If any equipment is missing contact your ANTARI dealer immediately. Before beginning your initial setup on ANTARI WiFi-800 Fog Machine, make sure that there is no evident damage caused by transportation. In the event that the unit’s housing or cable is damaged, do not plug it in and do not attempt to use it until after contacting your ANTARI dealer for assistance.
Android. Connecting mobile devices with iOS / Android to WiFi-800 Connexion d'appareils mobiles iOS / Android avec WiFi-800 Step 1: On your mobile devices, select Settings > Wi-Fi > list of available Wi-Fi device will be shown. Pas 1: Sélectionnez Settings > Wi-Fi sur vos appareils mobiles. Step 2: Select WIFI800-0000XXXX (e.g. WIFI800-00001001). “0000XXXX” is based on the last four digits of the serial number, which is printed on the rear of the machine (near the power cord).
Step 3: A password query is displayed. The password is an 8-digit number, based on the last four digits of the serial number (e.g. 00001001). Enter the password to connect to the machine, and wait until the network name is checked. Pas 3: La demande de mot de passe s'affiche. Le mot de passe est un numéro à huit chiffres fondé sur les quatre chiffres derniers du numéro de série (p. ex. 00001001).
Timer Mode – allows you to set the fog duration time. Slide the time bar (from 1 to 60 seconds); press ON to start emitting fog. The fog emission will stop once the timer counts down to zero. Continuous Mode – simply press the ON button to emit fog. The machine continuously emits fog; to stop press the OFF button. Note: If the ON button is pressed and the machine cannot emit fog, please make sure the continuous cycle button is turn on.
Configurations Wi-Fi avancées devraient être utilisées seulement par des personnes avec la connaissance experte. A web-based configuration panel allows you to customize your Wi-Fi settings. To start the configuration, first establish a Wi-Fi connection with the machine, then open a web browser, enter http://192.168.16.254 and when the login window appears enter the default user name admin and password admin. The configuration panel is displayed.
Wireless settings > Basic Network Mode Select one of the following that meets your clients 11b/g mixed mode 11b only 11g only Network Name(SSID) Broadcast Network Name(SSID) AP Isolation Frequency (Channel) 11b/g/n mixed mode default 11n only(2.4G) The name of your wireless network, create a name for your wireless network using up to 32 characters. Enable is default setting. If Disable is selected, the SSID of the machine will not be seen.
Wireless Settings > Security Select a SSID to start configuration Choose one of the following mode for data protection: Disable OPENWEP SSID choice Security Mode WPA-PSK WPA2-PSK WPA Algorithms Pass Phrase Key Renewal interval WPAPSKWPA2PSK (default) TKIP AES TKIPAES Setup password Enter the amount of time before the group key used for broadcast and multicast data is changed (3600 is default) Administration > Management Account Password Change login account name (default is admin) Change login p
Technical Specifications Model Power Supply WiFi-800 AC100-120V, AC 220-240V / 50HZ - 60HZ 800 W Power Consumption Output Volume 3000 Cubic Feet / Min Tank Capacity 0.8 Liter 60 Min. / 0.8 Liter Fluid Consumption 4.1 kg Weight Dimensions (LxWxH) 315 x 128 x 220 mm Optional Controllers Z-10 On/Off Controller, Z-40 Timer Controller, Z-50 Wireless Controller 1.7 min First Heat-up Time Optional Controllers for WiFi-800 Z-10: 10 meter wired remote controller with 1/4 inch jack plug.
Z-10, Z-40, Z-50 Remote Controls Performance Note All fog machines develop condensation around the output nozzle. Because this may result in some moisture accumulation on the surface below the output nozzle, consider this condensation when installing your unit. All fog machines may sputter small amounts of fog occasionally during operation and for a minute or so after being turned off. Maintenance Do not allow the fog liquid to become contaminated.
Note: Cleaning your fog machine regularly can help reduce replacement and repair costs. After a certain period time of usage, all fog machines tend to clog due to the thick consistency of fog liquid and the high temperature at which it vaporizes. However, a properly maintained fog machine should provide a longer and more reliable life-time. Storage 1. When the machine is not in use, store it in a cool and dry place. 2.
Bedienungsanleitung Herzlichen Glückwunsch zum Kauf Ihrer neuen Nebelmaschine ANTARI WiFi-800. Einfü hrung Vielen Dank, dass Sie sich für die Antari-Nebelmaschine WiFi-800 entschieden haben. Sie sind nun im Besitz einer robusten und leistungsstarken Nebelmaschine. Vor Benutzung der Maschine bitte unbedingt diese Bedienungsanleitung sorgfältig lesen.
Brandgefahr Nur für Erwachsene. Die Maschine muss außerhalb der Reichweite von Kindern installiert werden. Betreiben Sie das Gerät niemals unbeaufsichtigt. Richten Sie die Austrittsdüse niemals direkt auf Personen. Der Ausstoß der Maschine ist sehr heiß . Halten Sie während des Betriebs einen Sicherheitsabstand von ca. 60 cm zur Austrittsdüse ein. Betreiben Sie das Gerät in gut belüfteten Räumen, bis der Tank leer ist. Bedecken Sie niemals den Luftaustritt der Maschine.
Auspacken und Prü fen der Maschine Ö ffnen Sie den Versandkarton und stellen Sie sicher, dass alle Teile, die für den Betrieb des Systems notwendig sind, in einem einwandfreien Zustand eingetroffen sind. Der Versandkarton sollte die folgenden Posten beinhalten: 1. 2. 4. Eine Nebelmaschine WiFi-800 Netzkabel Bedienungsanleitung Wenn Ausrü stungsteile fehlen sollten, nehmen Sie bitte sofort mit Ihrem Antari-Händler Kontakt auf.
App herunterladen Laden Sie die App Antari Fog 800 im App Store herunter. Die App dient zur Steuerung der WiFi-800 in Verbindung mit Ihrem mobilen Gerät mit iOS- oder Android-Betriebssystem. Mobile Geräte mit der WiFi-800 verbinden Schritt 1: Wählen Sie auf Ihrem mobilen Gerät: Einstellungen (Settings) > WLAN. Die Liste der verfügbaren WLAN-Geräte wird angezeigt. Schritt 2: Wählen Sie WIFI800-XXXXXXXX (z. B. WIFI800-00001001).
Schritt 3: Die Passwortabfrage erscheint. Das Passwort ist die achtstellige Kennung, die sich aus den letzten vier Ziffern der Seriennummer ergibt (z. B. 00001001). Geben Sie das Passwort ein, um eine Verbindung zur Maschine aufzubauen. Warten Sie, bis der Netzwerkname ein Häkchen bekommt.
Timer-Betrieb: Bestimmen Sie eine Zeit für die Nebeldauer zwischen 1 und 60 Sekunden. Verstellen Sie dazu die Leiste und drücken Sie ON, um den Nebelausstoß auszulösen. Wenn der Timer auf 0 Sekunden zurückgezählt hat, wird der Nebelausstoß wieder eingestellt. Dauernebel: Drücken Sie einfach auf ON, um den Nebelausstoß auszulösen. Die Maschine produziert nun fortwährend Nebel. Drücken Sie die Taste OFF, um den Nebelausstoß wieder einzustellen.
Die Webschnittstelle wird angezeigt. Wireless-Einstellungen > Basic Network Mode Network Name(SSID) Auswahl: 11b/g mixed mode 11b only 11g only 11b/g/n mixed mode Vorgabewert 11n only (2.4G) Netzwerkname, Sie können einen beliebigen Namen definierten (32 Zeichen stehen zur Verfügung).
Broadcast Network Name(SSID) AP Isolation Frequency (Channel) Enable (aktiviert) ist die Voreinstellung. Wenn Disable (deaktiviert) gewählt wird, wird das SSID der Maschine nicht angezeigt. Der Benutzer muss dann das SSID kennen, um eine Drahtlosverbindung herzustellen. Verhindert, dass Geräte, die mit AP verbunden sind, direct miteinander kommunizieren. Die Voreinstellung ist Disable (deaktiviert). Wahl der Ü bertragungsfrequenz.
für Ü bertragung und Multicast von Daten geändert wird (3600 ist der Vorgabewert) Administration > Management Account Password Ä ndern des Login-Accountnamen (Vorgabewert ist admin) Ä ndern des Login-Passworts (Vorgabewert ist admin) 36
Technische Daten Modell WiFi-800 Spannungsversorgung AC 100-120 V, AC 220-240 V, 50 Hz/60 Hz Gesamtanschlusswert 800 W Ausstoß volumen 85 m³/Min. Tankinhalt 0,8 Liter Fluidverbrauch 60 Min. / 0,8 Liter Gewicht 4,1 kg Maß e (LxBxH) Fernbedienungen (Zubehö r) 315 x 128 x 220 mm Z-10 On/Off Controller, Z-40 Timer Controller, Z-50 Wireless Controller Aufwärmzeit 17 Min.
Reinigung und Wartung Achten Sie darauf, dass die Nebelflüssigkeit nicht verunreinigt wird. Setzen Sie sofort nach Befüllen des Tanks den Deckel des Tanks sowie des Kanister wieder auf. Reinigen Sie Ihr Nebelgerät regelmäß ig, um hohe Kosten für Ersatzteile und Reparaturen zu vermeiden. Nach 40 Betriebsstunden wird empfohlen, das Heizelement mit destilliertem Wasser zu reinigen. 1. Füllen Sie destilliertes Wasser in den sauberen Tank und stecken Sie den Flüssigkeitsschlauch in den Tank. 2.
Antari WiFi800 煙霧機 感謝您選用 Antari 煙霧機產品,現在您已經擁有高科技的專業煙霧機, 在開始使用之前,我 們建議您先仔細閱讀本說明書,遵循使用手冊中的說明, 這會有助於您在使用 Antari 煙霧機 時得心應手,達到最滿意的煙霧效果,對於機器的使用壽命也更為延長。 ! 特別注意: 請在連結電源之前,先填裝好煙霧油,器使用完畢及搬運前,請先確認清空煙霧油桶.
避免燃燒的安全使用方式: 機器內部並無一般使用者可變動之結構,請勿任意打開上蓋及作任何更改的動作,否則可 能造成起火的危險! 機器僅限成人使用,安裝煙霧機之地點應避免兒童可處及之出,請於外出離去時確實關閉 電源。 請勿將機器噴嘴對著人體及動物直射。 煙霧機所產生的煙霧溫度較高,機器運作時,請遠離噴嘴 50CM 以上。 請將煙霧機放置於通風良好的地方,請勿遮蓋機器散熱部分,為確保適度通風,機器的上 方及周圍請預留 20CM 空間。 請勿將機器噴嘴對準火焰。 當機器運作時,噴嘴輸出部分之溫度高達攝氏 200 度,請將任何物品放置離機器 50CM。 清潔、從事維護及收納機器時,請先確認機器已經完全冷卻。 避免爆炸的安全使用方式: 請勿將任何可燃性液體( 例如油脂, 瓦斯, 香水),放置於煙霧油槽中,並請使用前詳細閱讀 說明書。 請使用代理商所推薦的 Antari 高品質 FLR / FLG 水性煙霧油,任意使用其他煙霧油產品, 可能導致堵管現象甚至造成內部零件腐蝕。 請確認煙霧油槽中有足夠的煙霧油,以免造成煙霧機幫浦空轉過
若您的 Antari 機器有任何不當運轉情況時,請即刻停止使用,倒出煙霧油,機器冷卻後, 仔細包好本產品(建議以原包裝) 送至代理商或經銷商處維修。 請記得在運送或郵寄本產品前,確定完全傾倒出所有在油桶中的煙霧油。 煙霧油不能飲用,誤飲時,如有任何不適請立即就醫,若不甚接觸眼睛,請即刻以水清洗。 建議: 在使用本機器之前,詳細的閱讀一次印刷在機器上蓋板及後背板的警語標示. 拆除包裝及檢視機器 請打開包裝確認機器運作的所有設備齊全,請參考配置圖,確認您所購買的機型應包括之項 目,倘若有缺少任何項目,請即刻聯絡 Antari 經銷商。 機器出廠時應包含以下物件: 1. 機器 一部 2. 電源線一條 3.
術標籤。 步驟 4:打開機器開關,進行加溫,此時手把按鈕上的 LED 狀態指示燈會“閃紅燈”。溫機 的時間需要約 2 分鐘。一旦機器達到工作溫度,狀態指示燈將亮起“紅色常 亮”。表是機器為準備完成。 步驟 5:開始噴煙動作,按下手把上的按鈕釋放按鈕來停止。 步驟 6:關閉機器時,把電源開關置於 OFF 位置。 程式下載 登入 App Store 下載 Antari Fog 800 應用程式, 這個程式可經由你的 iPhone 或 iPad 來 操控 WiFi-800 將 iPhone/ iPad 連結到 Wifi 800 步驟 1. 進入到你的 iPhone/ iPad 的設定選單 > 選取 Wi-Fi > 系統會列出所有可用的 Wi-Fi 裝置 步驟 2.
SSID 的系統預設值和密碼 步驟 3.
定時模式 - 可以設定煙霧持續輸出時間, 滑動時間桿, ( 從 1 到 60 秒 ) 按壓 ON 開始輸 出煙霧. 時間開始倒數, 煙霧將停止於結束倒數直到 0.
Wi-Fi 進階設定 透過網頁設定介面,使您可以自定義 Wi-Fi 模組的相關設置。開始設置前請確認已和機器完成 連結,然後打開一個網頁瀏覽器,輸入 http://192.168.16.
無線設定 > 基本設定 無線訊號 無線訊號 ON 或 OFF On 為系統預設值 Off WiFi WiFi 訊號 ON 或 OFF On 為系統預設值 Off 網路模式 選擇下列一個客戶端相容的模式 11b/g mixed mode 11b only 11g only 11b/g/n mixed mode(系統預設值) 47
11n only(2.4G) 網路名稱 設定一個無線網路名稱以便使用, 最高可以使用到 32 個字元. 廣播網域名稱 (SSID) 此功能預設值是開啟的, 如果停用此功能,則無法搜尋到該網路.使用 者需要知道該網路名稱才能連結.
OPENWEP WPA-PSK WPA2-PSK WPAPSKWPA2PSK(系統預設值) WPA 加密模式 TKIP AES TKIPAES 密碼設定 設定密碼 金鑰更新時間 設定資料傳輸值金鑰更新時間(預設值為 3600) 系統設置 > 管理 帳戶名 修改用戶名稱 ( 預設值 admin ) 密碼 更改登錄密碼 ( 預設值 admin ) 49
備註: (4-手把燈):慢閃表示加熱,恆亮表示加熱完成,快閃表示機器過熱此時請檢修後再行使用 (12- LED):(一)WiFi800 與手機連上線時紅燈將會亮起,若無亮起請檢查手機是否有 WiFi 連線符號。 50
(二)噴煙啟動時會亮橘色燈。 亮紅燈但機器無法噴煙:請檢查上面設定第 8、9 點是否設定正確 WiFi800 控制器 (選配) Z - 10 On/Off 控制器:10M 長電線含 6.3mm 耳機 插頭控制器,綠色燈閃亮時顯示控制器 正在接收電源,當煙霧機到達運轉溫度時,控制器上的綠燈會持續亮,停止閃動,顯示可以按 紅色按鈕讓煙霧機開始噴煙,當綠燈開使閃動表示煙霧機處於重新暖機狀態,重新熱機循環約 45-60 秒,並在綠燈亮時機器可以開始運轉 Z - 40 定時控制器:10M 長電線及 6.3mm 耳機插頭控制器,使用時,只要按下紅色電源 Power 按鈕,即可啟動遙控功能,其兩個旋鈕可自由調整噴霧時間與間隔的設定,若按黃色定時按鈕 便可啟動定時功能調整噴煙時間間隔 (介於 10 秒至 250 秒) 只要按 Intervl 及調整噴煙時間 長短按 Duration (介於 10 秒到 120 秒之間) 即可,當按住此控制鈕時,綠色 Fog 按鈕會超 越其他功能,並且達到 100%的輸出量。 Z – 50 無線遙控:具 6.
其他注意事項 1. 煙霧機在使用一段時間後,噴嘴附近會有一些灰色沉澱物質,是因為液體經過熱交換而產 生的自然現象,只要將它擦乾淨即可,如發現噴嘴附近有黑色濃稠的沉澱物時,請檢視所 用的煙霧油,是否為成分不良品,並請停止使用,以維護機器使用壽命。 2. 所有的煙霧機可能因為使用不同煙霧油之濃度及長期加熱高溫蒸發造成阻塞,使用好品質 的煙霧油,定期的清潔保養,可使機器保持良好運轉。擦拭機器時請使用乾布,機器不用 時需放置於陰涼、通風處。 3.
1. 拔掉機器插座,冷機時鬆開機器前方之噴嘴,清理噴嘴中殘餘碎屑,直到確認管中未被阻 塞。 2. 倒出機器中的煙霧油,在油桶中加入蒸餾水,插上插頭暖機。 3. 在通風良好處,讓機器運轉一段時間。 4. 清潔完畢用乾布完全擦拭乾淨機器後再注入煙霧油。在機器不使用需收起來之前請先清潔 機器並確定將油桶清空,並拆下控制器與電源線收好,整套機器與配件請存放於乾燥陰涼 處,每月固定溫機一次,可保護機器較不受潮。 WiFi-800 數據規格 型號 WiFi-800 適用電源供應 AC100-120V, AC 220-240V / 50HZ - 60HZ 瓦數 800W 輸出功率 (立方英呎/ 每分鐘) 3,000cu.ft/min 煙霧油桶容量 (公升) 0.8 Liter 耗油量 ( 每分鐘/ 公升) 60 Min./ 0.8 Liter 重量 4.1 Kg 尺寸 (mm) 選擇性配備 L315 W128 H220 Z-10 ON/OFF 控制器、Z-40 定時控制器、Z-50 無 線控制器 溫機時間 1.
This is world’s 1st SmartPhone controlled fog machine:Antari WiFi800 .
C08WF8002 56