High Efficiency Vaporizing System and Highly Durable Heaters Ensure 25% Increased Output. Modular Design for Easy, Cost Effective Maintenance. Standardized Interface Allows Interchangeable Control Modules on All Models. Illuminated Fluid Tank for Easy Monitoring for the Level of Fog Fluid. Electronic Low Fluid Monitoring Protects Pump from Running Dry Heavy-Duty, Quiet Pump for Continuous, Silent Operation.
Table of Contents Introduction 1 Important Safeguards 2 Unpacking & Inspection 4 Setup 4 Operation 5 Control Module Operation 6 ANTARI X-20 DMX Module Settings 8 Maintenance Performance Notes 10 11
Congratulations on the purchase of your new ANTARI X Fogger Introduction Thank you for choosing an ANTARI X Fogger. You now own a rugged and powerful state-of-the-art machine. Prior to use, we suggest that you carefully read all of the instructions. By following the suggestions found in this user manual, you can look forward to the reliable and satisfactory performance of your ANTARI Fog Machine for years to come.
Important Safeguards Danger of Electric Shock ! ! ! ! ! ! ! ! Keep this device dry. For inside use only. Not designed for outside use. For the 110V models, use 3-prong grounded electrical outlet only. Prior to use take care to determine that the unit is installed at the rated voltage. Always unplug your ANTARI Fog Machine before filling its tank. Keep fog machine upright. Unplug the machine when not in use. This machine is not water- or splash-proof.
! ! ! ! Never aim the output nozzle at open flames. If the supply cord is damaged, it must be replaced by manufacturer or its service agent or similarly qualified personnel in order to avoid a hazard. The output nozzle becomes very hot during operation (300 0C). Keep flammable materials at least 50 cm away from the nozzle. Always allow your ANTARI X Fogger to cool down before attempting to clean or service it.
Unpacking & Inspection Open the shipping carton and verify that all equipment necessary to operate the system has arrived intact. Before beginning initial setup of your ANTARI Fog Machine, make sure that there is no evident damage caused by transportation. In the event that the unit's housing or cable is damaged, do not plug it in and do not attempt to use it until after contacting your ANTARI dealer for assistance. Setup Remove all packing materials from shipping box.
Operation ! Plug power cord into a grounded electrical outlet. T urn power switch on rear of unit to " ON" position. ! ! ! Warm-up is complete when the display on control module.shows " Ready to Fog" To emit fog, press the appropriate button on the control module for the desired length of time. The control unit's display will cycle " Warming up" and " Ready to Fog " as the machine re-heats to the proper operating temperature.
going through the hose. If you are unable to determine the cause of the problem, do not simply continue pushing the control module button, as this may damage the unit. Return the machine to your ANTARI dealer immediately. Control Module Operation FUNCITON ! TIMER VOLUME MANUAL ESC ENTER ON / OFF X-10: 10 meter wired multi-function remote control module with 5-pin XLR connector for ANTARI X Series models X-310, X-510, X-515, X-530.
percentage (within the range of 1% to nonstop burst) by means of Up / Down keys. To adjust timer setting, go into Timer option. Cycle through Interval (within the range of 1 to 900 seconds), Duration (within the range of 1 to 200 seconds), and Volume (within the range of 1% to nonstop burst) by means of Up / Down keys. Use Enter (Volume) Key to select each option and make changes as desired. To turn off the heater and fan, go into Heat & Fan option. Use Enter (Volume) Key to confirm the selection.
! X-30: All the X-10 features plus wireless capability. Wireless operation is possible up to a distance of 50 meters. The address can be set from 0 to 8, which means total 9 different units can be controlled separately or in any combination desired. Press function to cycle to RF mode to select desired address number. Make sure the address setting on the X-30 matchs the address setting on the transmitter. There are two buttons on the transmitter. One is to release fog, the other is to stop the operation.
If Channel has a value from 0 to 5, the unit is OFF. Between the values 6 to 249 the volume of fog output is regulated.With 6 being the minimum volume of fog produced and 249 approaching the maximum. The volume output rises as the DMX value is increased. If Channel has a value from 250 TO 255, the machine will operate at maximum output. Note: In the example above, if the machine were assigned the DMX address of 124, Channel would correspond to DMX address 124.
Maintenance Do not allow the fog liquid to become contaminated. Always replace the caps on the fog liquid container and the fog machine liquid tank immediately after filling. After every 40 hours of continuous operation, it is recommended to run a cleaning solution composed of 80% distilled water and 20% white vinegar through the system to prevent the accumulation of particulate matter in the heating element. The recommended cleaning regimen is as follows: 1.Empty all fog fluid from machine.
Performance Notes ! ! ! ! All fog machines develop condensation around the output nozzle. Because this may result in some moisture accumulation on the surface below the output nozzle, consider this condensation when installing your unit. All fog machines may sputter small amounts of fog occasionally during operation and for a minute or so after being turned off. All fog machines have a recycling period after long bursts when the machine will shut itself down for a short period in order to heat up again.
LIMITED WARRANTY Atari Lighting and Effect Ltd. warrants to the original purchaser that the ANTARI X Fogger will be free from original defects in workmanship and material for a period of six months from the date of purchase. During the warranty period, machines will be repaired or replaced at the option of ANTARI or its designated dealer.
