NINE HUNDRED TWO V3 USER’S MANUAL
Table of Contents Introduction 1.1 1.2 Case Specifications .............................................................................................3 Diagram ..............................................................................................................3 Hardware Installation Guide 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 2.10 2.11 Setting Up ..........................................................................................................4 Power Supply Installation ................
Congratulations on your purchase of the Nine Hundred Two V3! The best-selling Antec Nine Hundred offers gamers an unbeatable enclosure, one that delivers a combination of cooling, performance and convenience and stands head and shoulders above the competition. The Nine Hundred Two V3 builds on this design, adding a CPU cutout, internal bottommounted 2.5” SSD drive bay and front USB 3.0 port.
1.1 Case Specifications Case Type Mid Tower Color Black Dimensions 19.3” (H) x 8.7” (W) x 18.5” (D) 493 mm (H) x 218 mm (W) x 472 mm (D) Weight 25.4 lbs / 11.5 kg 1 x Top 200 mm TriCool™ Blue LED 3-speed Fan 2 x Front 120 mm Blue LED Fan with Front Control Knobs 1 x Rear 120 mm TriCool™ Blue LED 3-speed Fan 1 x Side 120 mm Fan Mount (Optional) 1 x Middle 120 mm Fan Mount (Optional) 10 Drive Bays: - Up to 9 x External 5.25” Drive Bays - Up to 6 x Internal 3.5” Drive Bays - 1 x External 3.
Hardware Installation Guide 2.1 Setting Up 1. Place the case upright on a flat, stable surface so that the rear panel (power supply and expansion slots) is facing you. 2. Remove the panel thumbscrews from the side panel and open it by sliding it towards you. Note: Place the panel thumbscrews carefully aside as they are NOT interchangeable with the HDD cage thumbscrews. 3. Remove the panel thumbscrews from the other side panel and open it by sliding it towards you. Place the screws carefully aside.
4. Lift up and remove the motherboard. 5. Screw in the brass standoffs to the threaded holes that line up with the motherboard. 6. Place the motherboard on the brass standoffs. Screw in the motherboard to the standoffs with the provided Phillips-head screws. 2.4 Flexi-Drive Bay System The Nine Hundred Two V3 comes with nine 5.25” external drive bays at the front of the case. There are three HDD cages pre-installed inside the bottom six 5.25” bays. Each HDD cage occupies three consecutive 5.
. There is a 120 mm fan pre-installed into each cage. Connect the 4-pin connector to the power supply. Note: There is a middle fan bracket pre-installed on one of the HDD cages. Remove it from the cage if you decide to mount your hard drives into this cage. 2.6 1. 2. 3. 4. 5. 6. 2.7 External 3.5” Device Installation Remove both side panels per the instructions in Setting Up. Remove the drive bay cover from the drive bay you wish to install an external 3.5” drive into. Install your external 3.
2.8 Internal 2.5” Device Installation At the bottom of your case, there are mounting holes designed to support one 2.5” SSD device. 1. Locate the plastic bag labeled “For 2.5 HDD” and remove the 4 silicone grommets. 2. Install the grommets into the four holes at the base of the case at the bottom of the drive bay area as shown. You should install them with the thick part of the grommets facing the inside of the case. 3.
2.10 Water Cooling Platform This case comes with a 5.25” metal plate pre-installed in the 3rd 5.25” drive bay. This plate is designed to allow you to easily mount components of a water-cooling kit such as a pump or reservoir. The plate can be mounted in any of the nine 5.25” drive bays for maximum flexibility. Note: The plate is not pre-drilled. You will need to drill the appropriate holes to be compatible with your water-cooling kit. 2.
3.3 AC’97/HD Audio Ports There is an Intel® standard 10-pin AC’97 connector and an Intel® 10-pin HDA (High Definition Audio) connector linked to the front panel of the case.
3.5 Rewiring Motherboard Header Connections There may come a time that you need to reconfigure the pin-out of a motherboard header connector. Examples could be for your USB header, audio input header, or some other front panel connector such as the Power Button connector. Before performing any work, please refer to your motherboard manual or your motherboard manufacturer's website to be sure of the pin-out needed for your connector.
Size: Rated Voltage: Operating Voltage: 4.2 200 x 30 mm three-speed fan 12V DC 10.8V ~ 13.2V Speed (RPM) Input Current Air Flow Static Pressure Acoustic Noise Input Power High 800 0.3A 3.8 m³ / min (134 CFM) 0.7mm-H2O (0.03 inchH2O) 30 dBA 3.6 W Medium 600 0.2A 3.1 m³ / min (108 CFM) 0.4mm-H2O (0.02 inchH2O) 27 dBA 2.0 W Low 400 0.1A 2.3 m³ / min (82 CFM) 0.2mm-H2O (0.01 inchH2O) 24 dBA 1.
Size: Rated Voltage: Operating Voltage: 120 x 25 mm TriCool™ fan 12V 10.2V - 13.8V Speed (RPM) Input Current Air Flow Static Pressure Acoustic Noise Input Power High 2000 0.24A (Max.) 2.2 m³ / min (79 CFM) 2.5mm-H2O (0.10 inch-H2O) 30 dBA 2.9 W Medium 1600 0.20A 1.6 m³ / min (56 CFM) 1.5mm-H2O (0.06 inch-H2O) 28 dBA 2.4 W Low 1200 0.13A 1.1 m³ / min (39 CFM) 0.9mm-H2O (0.04 inch-H2O) 25 dBA 1.6 W Note: The minimum voltage to start a 120 mm TriCool™ fan is 5V.
5. 6. the holes in the fan are secured to the mount. Use the long screws provided to secure the fan to the mount. Do not overtighten. Run the power (and control switch if using a TriCool™ fan) through the cable guide that runs along the side of the mount. Clip the assembly onto the back of an empty HDD cage. Connect the fan to the power supply. 4.4 Washable Air Filters 3. 4. Front Air Filters – There is a filter located behind the faceplate of each HDD cage faceplate.
Antec, Inc. 47900 Fremont Blvd. Fremont, CA 94538 USA tel: 510-770-1200 fax: 510-770-1288 Antec Europe B.V. Stuttgartstraat 12 3047 AS Rotterdam The Netherlands tel: +31 (0) 10 462-2060 fax: +31 (0) 10 437-1752 Customer Support: US & Canada 1-800-22ANTEC customersupport@antec.com Europe +31 (0) 10 462-2060 europe.techsupport@antec.com www.antec.com © Copyright 2011 Antec, Inc. All rights reserved. All trademarks are the property of their respective owners.
