ANTHEM INTEGRATED 1 OPERATIN G MA NU A L
We at Sonic Frontiers hope you will derive many years of listening pleasure with your new Anthem Integrated 1. This Operating Manual contains important information regarding the operation and care of the Integrated 1. Be sure to read this manual carefully and follow these instructions in order to keep your unit performing and sounding its best. Please contact Sonic Frontiers if you have any questions, a Customer Service Representative will be pleased to assist you.
A B D E C F G
CONTROL A FUNCTIONS SELECTOR S WIT CH This knob is rotated to select a Line Level Input (L) or the optional Phono Input (O). The Selector Switch is bypassed when the Tape/EPL (External Processor Loop) mode is selected by depressing the Tape/EPLSource button (D). B VOLUME CONT RO L This knob allows variable control over the Integrated 1 output level.
H I J K L M N O
CONNECTION FUNCTIONS NOTE: The Integrated 1 is shipped in the “integrated amplifier” configuration. For use as a separate “preamplifier” and/or “power amplifier”, refer to Figure 1 and points J and M for instructions. H D E TACHABL E AC PO WER CO RD SOCKET Plug the Detachable Power Cord into this socket (see Figure 2). The Integrated 1 is factory set for the correct operating voltage for the area in which it is sold (see shipping box for voltage setting).
O OPTIONAL PHONO INPUT AND G RO UND CONNECT IO N This input is designed to replace the AUX 2 line level input when the optional phono input module is installed. This extra amplification stage provides additional gain when dealing with sensitive signals from moving magnet phono cartridges. Connections are made from a turntable; left channel to left channel and right channel to right channel.
1 2 AT 7 (V3 ) FIRST STAGE AMPLIF ICATION TUBE EL84 (LV4,5 ,6,7 & V4,5,6,7) POW ER TUBES The first stage of amplification in the amplifier section of the Integrated 1 is achieved through the use of this dual triode, amplifying both channels, one per triode section. The 12AT7 may be replaced with the ECC81, E81CC, ECC801S, 6201, CV4024or M8162 tube. These tubes provide the last stage of amplification, set up in push/pull pairs (4 tubes per channel, two per phase).
IN SE RTION OF THE T UB ES 1. Using the screwdriver supplied, remove the cover of the Integrated 1. For your convenience, only two of the screws are installed at the factory. 2. When handling the tubes, it is recommended that the cotton gloves provided be worn to prevent skin oils from depositing on the glass surface and possibly causing the tube to become prematurely “gassy”, thereby shortening the tube’s useful operating life. 3.
or the Integrated 1. To record from a source, place the Tape/EPL-Source button (D) in the SOURCE position, select the source material you wish to record via the Selector Switch (A), and commence recording. To play back a tape recording, place the Tape EPL/ Source button in the TAPE position. Muting the Integrated 1 is achieved by placing the Mute/Operate button (G) in the MUTE position (button depressed); the output signal is then cut off.
BREAK-IN T IME PACKING MAT E R I A L S As with all audio electronic products, the ultimate sonic character of the Integrated 1 will not be realized until and unless the unit receives a minimum of approximately 70 hours of signal break-in time (i.e. the Integrated 1 is on and outputting a signal). Please retain all of the packing material and shipping boxes for your Integrated 1. They are custom designed to prevent shipping damage from occurring. Sonic Frontiers, Inc.
4. Sonic Frontiers, Inc. shall not be responsible in any way for consequential or indirect damages or liabilities resulting from the use and operation of the product covered herein or resulting from any breach of this warranty or any implied warranty relating to said product. During this period, Sonic Frontiers, Inc. will repair or replace any defective components free of charge. A Return Authorization Number (RA Number) is required before any product is returned to our factory for any reason.
T E C H N I C A L S P E C I F I C AT I O N S (AC line set at 117V 60Hz) P R E A M P L I F I E R S P E C I F I C AT I O N S Line Level Inputs to Pre Outputs INPUTS (6): CD, Tuner, Aux 1, Aux 2/Phono, Tape INPUT IMPEDANC E: 750k ohms (line level inputs) and Power O UTPU T IMPEDANCE: 7k ohms (minimum required load: O UTPU TS (3): Tape, Preamplifier and Main Power 100k ohms) Amplifier (0,4,8 ohm) FR EQ UENCY RESPONSE: -0.5dB 30Hz to 20kHz, CONTROLS ( 3): Input Select, Balance, Volume -3.
D E S I G N E D A N D M A N U F A C T U R E D B Y 2790 BR IG HTON ROA D, OAK VI LL E , O NTA RI O, C A NAD A S o n i c F r o n ti e r s E - M A I L : c a n b e r e a c h e d 9 : 0 0 S F I @ s o n i c f r o n t i e r s . c o m a m t o S O N I C L6H 5T4 6 : 00 W W W : p m F R O N T I E R S I N C O R P O R A T E D T EL : (9 05) 82 9- 38 38 ( E. S. T. ) o r 24 h o u r s FA X: ( 905 ) 8 29 -3 033 a d a y by fa c s i m il e h t t p / / w w w . s o n i c f r o n t i e r s .
