M1_MANUAL_COVER_ENG_081611_Layout 1 11-08-17 10:40 AM Page 70 DESIGNED AND MANUFACTURED IN NORTH AMERICA t e l . ( + 1 ) 905-362-0958 M-F 9:00 am - 5:30 pm (ET) w w w. a n t h e m AV.
SAFETY PRECAUTIONS READ THIS SECTION CAREFULLY BEFORE PROCEEDING! CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE, AND OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD NOT BE PLACED ON THIS APPARATUS.
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat. 9.
WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. Avoid installing this unit where foreign objects may fall onto this unit and/or this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place: • Burning objects (i.e. candles), as they may cause fire, damage to this unit, and/or personal injury.
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
IMPORTANT INFORMATION FOR UK CUSTOMERS: DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. If, nonetheless, the mains plug is cut off, REMOVE THE FUSE and dispose of the PLUG immediately, to avoid possible shock hazard by inadvertent connection to the mains supply.
NOTES ON ENVIRONMENTAL PROTECTION At the end of its useful life, this product must not be disposed of with regular household waste but must be returned to a collection point for the recycling of electrical and electronic equipment. The symbol on the product, user’s manual and packaging, point this out. The materials can be reused in accordance with their markings.
1. INTRODUCTION Thank you for purchasing Anthem Statement M1 Power Amplifier. All Anthem products are engineered to recreate the passion of a live musical performance and emotional involvement experienced in the best movie theaters by utilizing the highest level of circuit design, superior parts and manufacturing techniques, innovative features, and intuitive ergonomics. We are confident that their inclusion in your system will significantly enhance your enjoyment of recordings for years to come.
1. INTRODUCTION (continued) 1.1 BEFORE MAKING CONNECTIONS Check that you have received everything on the packing list and report discrepancies to your dealer as soon as possible. Retain the packing materials and the invoice that you received from your authorized Anthem dealer at time of purchase – without it, service will not be provided under warranty.
1. INTRODUCTION (continued) • Failing to comply with any safety instruction, precaution, or warning in this manual is in violation of the intended use of the product. • Anthem and any related party assume no liability for the user’s failure to comply with requirements. 1.2 IN-USE NOTICES • Disconnect the power cord before connecting or disconnecting any components. • If the product was transported or stored in the cold, let it warm to room temperature before use. • Do not remove the top cover.
2. CONNECTIONS AND OPERATION 2.1 INPUT CONNECTIONS Balanced XLR connection offers the highest transmission quality, particularly over long cable lengths, because it rejects noise and hum pickup. If using the XLR input, set the input switch to the 0 dB position if your preamplifier’s XLR outputs are at normal line level, or to the -6 dB position if your preamplifier’s XLR outputs are at 2x line level. If your preamplifier does not have XLR outputs, use the RCA inputs.
2. CONNECTIONS AND OPERATION (continued) 2.3 ON MODES With the three-way switch located on the rear panel, you can set the way the amplifier is turned on and off. To use Trigger-On, connect a standard 3.5mm (.125”) mono mini plug cable between the amplifier and the preamplifier or control component. Once all other connections are made, connect the power cord to the amplifier and then the wall outlet. Manual-On: When in this position, the amplifier is turned on/off via the power button on the front panel.
2. CONNECTIONS AND OPERATION (continued) 2.
2. CONNECTIONS AND OPERATION (continued) 2.
3. LED INDICATION CODES Power LED: This is on when the amplifier is operating normally and off at all other times. Status LED: Normal brightness indicates operate mode. If the M1 detects a problem, the amplifier output will turn off for 12 seconds* and the LED will flash a number of times, pause for 2 seconds, and repeat the flash cycle to allow the user to count the number of flashes per cycle before the power button is pressed twice.
3. LED INDICATION CODES (continued) 4 flashes: Temperature exceeds limit. Make sure there is adequate ventilation. The amp will resume operation only once internal temperature drops within acceptable range (4 degrees Celsius less than fault). 6 flashes: Average input current exceeds limit. This fault is activated to avoid nuisance AC input interruption. This condition can occur if two or more speakers are connected in parallel. The amplifier should be connected to a dedicated circuit.
SPECIFICATIONS Power Output continuous, 20 Hz to 20 kHz, <0.1% THD+N 8 Ω .............................................................................................................................................................................................1000 W With 120V AC supply the amplifier’s maximum output into impedances 4 Ω and lower, as well as its maximum duration, vary depending on line voltage regulation. Frequency Response 20 Hz to 20 kHz open circuit .....................................
SPECIFICATIONS (continued) Voltage Gain.................................................................................................................................................................29 dB Input Sensitivity ...........................................................................................................100 mV for 1 W output, 3.2 V for 1000 W output (8 Ω) Input Impedance ..............................................................................................................
SPECIFICATIONS (continued) Where mains voltage is 120V, one dedicated 15A circuit per amplifier is recommended depending on speaker. A 20A circuit is adequate for two amplifiers playing music where speaker impedance is 8 Ω. This product operates from a single phase AC power source that supplies between 108V and 264V at a frequency of 50 or 60 Hz. DIMENSIONS Height with feet......................................................................................................................................
LIMITED WARRANTY CANADA & USA The warranty period on new Anthem products is: 5 years: Separate power amplifiers and integrated amplifiers 3 years: Audio/Video preamplifiers and receivers 2 years: Projectors, Blu-ray players 1 year: All remote controls 6 months: Projector lamps The warranty period begins on the date of purchase from Anthem or an Authorized Anthem Dealer.
LIMITED WARRANTY (continued) A Return Authorization (RA) number must be obtained from Anthem Technical Support before a product can be shipped to Anthem for any reason. Product shipped to Anthem without its RA Number clearly visible on the outside of the shipping carton will be refused and returned to the sender, freight collect.
NOTES
NOTES
