manual

Anthro Corporation Technology Furniture
®
10450 SW Manhasset Drive Tualatin, Oregon 97062
anthro.com
Step 4
Determine the height of your Shelf. These Instructions will
place your final Shelf height at either 29” or 35” from the floor
(depending on which height Bench you purchased).
The holes along the Leg Assemblies are spaced at 1”
increments. Adjusting either one hole up or down will modify
the final Shelf height by 1” respectively. Rotating the Glides
will also provide additional height adjustment.
NOTE: Your Shelf height can be adjusted at a later time if needed,
however, Assembly Steps 5 through 8 will need to be disassembled
and reassembled again.
Step 5
Position the Left Bench Arm onto the Left Leg Assembly.
Align the top two openings of the Arm with Hole 2 of the
Leg Assembly. Loosely install a Support Screw through the
top two holes of the Arm into the Leg.
Install the remaining six Support Screws into the Left Arm,
but do not fully tighten any of the Support Screws.
Repeat entire procedure for the Right Bench Arm on the
Right Leg Assembly.
Step 6 (requires a 3-Way Wrench)
Position a Bench Pan between the Arms, aligning the
two tabs on each Arm with the two holes in the lower
corners of a Pan. Insert a Pan Screw through the Pan
and Arm Tab- capturing it with a Keps Nut
(but do not
fully tighten). Repeat this procedure for the remaining
end of the Pan and for the second Pan.
Tighten all Pan and Support Screws.
NOTE: the 3-Way Wrench can be used to assist in tightening
the Keps Nuts.
Questions? 1-800-325-3841
(
1
/
4
-20 X .5”) Pan Screw
325-5003-00
Support Screw
325-5010-00
Insert Screw
(small pink patch on end)
325-5052-00
Glide Inserts placed
into the large holes
Leave these two holes open
(
5
/
16
-18 X 4”) Bench Cap Screw
325-5166-00
Curved Washer
225-2050-00 or 225-3522-00
29” or 35”
Left Leg Assembly
Right Leg Assembly
Side holes
Cross Tubes
Leave top two
Holes open
Hole 2
Left Leg Assembly
Right Leg Assembly
(
1
/
4
-20) Keps Nut
325-5130-03
(
5
/
16
-18 X 4”) Bench Cap Screw
325-5166-00
Curved Washer
225-2050-00 or 225-3522-00
Leave these two holes open
Lower holes
Arms
Second Pan shown installed
REMINDER: You may want to measure
your equipment to make sure it fits into
the selected Shelf location.
48” AnthroBench
Assembly Instructions
Left Bench Arm
Step 3
Position the Right Leg Assembly (from Step 2) with two
Cross Tubes as shown. Insert one Bench Cap Screw
with a Curved Washer through a side hole, carefully
threading the Screw into the Cross Tube.
Repeat entire procedure for the remaining three
side holes.
Step 2
Orient one Bench Leg Assembly with one Base Tube
Assembly (from Step 1). The Glide Inserts should be facing
down.
Insert one Bench Cap Screw through one Curved Washer,
then carefully insert through one of the lower holes on
the Base Tube, threading into the Right Leg Assembly.
Repeat this procedure for the remaining three lower holes
on the Right & Left Leg Assembly.
STOP: If you are upgrading to 5” Casters do so now.
Finally, thread one Bench Glide into each Glide Insert.
Left Leg
Assembly
Right Leg
Assembly
Thread one Glide
i n t o e a c h G l i de
Inser t AFTER the
Base Tubes have been
installed to the Legs.
NOTE: Loosen these
Support Screws (if
needed) to allow the
Base Tube to install
easier.
Glide Inserts
Step 1
Install two Bench Glide Inserts into each Bench Base Tube
and secure with one Insert Screw per Insert.
Pop two End Caps into the ends of both Base Tubes.