Assembly Instructions User guide

ManualsBrandsAnthro ManualsFurnitureElevate II Adjusta

ASSEMBLY INSTRUCTIONS

Anthro Corporation

| 10450 SW Manhasset Dr. | Tualatin, OR 97062

Toll-free: 800.325.3841 | Fax: 800.325.0045 | email: sales@anthro.com | anthro.com

Outside the U.S. | Tel: 503.691.2556 | Fax: 503.691.2409

Elevate II Adjusta

Rev C, January 2014

NOTE: The CPU SideRack - Inboard is not included.

Part # Product

MVJA48zz-xx ELT 2 Adjusta Basic 48w

MVJB48zz-xx ELT 2 Adjusta Plus 48w

MVJA60zz-xx ELT 2 Adjusta Basic 60w

MVJB60zz-xx ELT 2 Adjusta Plus 60w

Certiﬁcation: Elevate II Adjusta is certiﬁed by ETL to UL962 standard for Commercial and Household furnishings.

Summary of content (8 pages)

PAGE 1
AS S E M B LY I NST R U C T I O NS Elevate II Adjusta Part # Product MVJA48zz-xx ELT 2 Adjusta Basic 48w MVJB48zz-xx ELT 2 Adjusta Plus 48w MVJA60zz-xx ELT 2 Adjusta Basic 60w MVJB60zz-xx ELT 2 Adjusta Plus 60w NOTE: The CPU SideRack - Inboard is not included. Anthro Corporation® | 10450 SW Manhasset Dr. | Tualatin, OR 97062 Toll-free: 800.325.3841 | Fax: 800.325.0045 | email: sales@anthro.com | anthro.com Outside the U.S. | Tel: 503.691.2556 | Fax: 503.691.
PAGE 2
IM P O RTA N T S AF E T Y I NST R U C T I O NS When using an electrical furnishing, basic precautions should always be followed, including the following. Read all instructions before using Elevate II Adjusta. DANGER To reduce the risk of electric shock, always unplug this furnishing from the electrical outlet before cleaning. WA RN IN G To reduce the risk of burns, fire, electric shock, or injury to persons: 1. Unplug from outlet before putting on or taking of parts. 2.
PAGE 3
01 03 04 07 02 06 08 05 15 13 14 12 W E L CO ME PA R T S L I ST Thank you for purchasing Anthro's Elevate II Adjusta electric lift table! Before beginning assembly of your Elevate II Adjusta, please review the parts list to verify that your shipment is complete. If you have any questions or if we can help you in any way, please contact us at 800.325.3841.
PAGE 4
STEP 1 - AT TA C H G U S S E T S TO TO P Lay the top surface upside down on a cushioned, non-marring surface. Locate the front edge of the table. On Plus tables, the front of the table has a sloping waterfall edge. On the Basic tables, the back edge of the table has the seam where the edgebanding meets. Align the Leg Gussets with the holes on the top so the upright flange faces the outside of the table and the tapering end points to the front of the table.
PAGE 5
STEP 3 - INS TA L L T H E C R O S S PA N Align the Cross Pan with the Leg Assemblies so the pair of flanges on the pan line up with the pre-drilled holes on the table. Attach the back of the pan to the top with four 1" MDF Screws (325-5580-00) and attach the front of the pan to the top with three 1" MDF Screws. Attach the pan to each leg housing with two M6x14 flat-head fasteners using the Anthro driver. Tighten all fasteners.
PAGE 6
STEP 6A - AS S E M B L E A D J U S TA M EC HA NI SM Brake/Paddle Assembly Brake Cable Your Adjusta mechanism comes unassembled and is boxed separately inside the package. Locate the small bag of hardware included with the Adjusta Mechanism. It includes (1) Post, (1) Cotter Pin, (2) Hex Nuts, (2) Wood Screws, and (2) Cable Mounts. Crossbar Brake Shaft Begin to assemble the mechanism by first locating the Crossbar and Brake/ Paddle assembly and position them as shown at right.
PAGE 7
STEP 8 - AT TA C H A D J U S TA M E CHA NI SM TO K EYB O A R D SU R FA C E Slide the Keyboard Surface under the mechanism arms. Align the three holes on each end of the Keyboard surface with the three holes on each mechanism arm. Secure the arms to the Keyboard Surface with six 1" Button-head Screws. Position the Paddle on the Keyboard Surface so the four holes on the Paddle align with the four holes on the Keyboard Surface and the brake cable runs under the Adjusta Bar.
PAGE 8
SA FET Y CH E C K Plug in the table and home the legs. To home the legs, move the table to its lowest position, release the DOWN button, then press and hold the DOWN button for 5 seconds. The table will bump a few times, then rest. Raise the table to its highest position. Watch all the cords and cables as the table moves to verify that cords aren't wrapped around anything and that nothing interferes with the movement of the table.